Make sure this part fits

GM 12612349
Oil Tube

2008-2012 GM

Customer Questions & Expert Answers (13)
GM 12612349 Oil Tube
GM 12612349 Oil Tube
  • Part Description
    Tube, Engine Oil Level; Oil Dipstick Tube
  • Manufacturer
    General Motors
  • Manufacturer's Notes
    This part is discontinued.
Make sure this part fits
  • Vehicle Fitment

    Year Make Model Trim Engine
    2010-2012 Buick EnclaveBase, CX, CXL6 Cyl 3.6 L GAS
    2010-2011 Buick LaCrosseCX, CXL, CXS6 Cyl 3.6 L GAS
    2008-2011 Cadillac CTSBase, Luxury, Performance, Premium6 Cyl 3.6 L GAS
    2008-2009 Cadillac SRXBase6 Cyl 3.6 L GAS
    2008-2011 Cadillac STSBase, Platinum6 Cyl 3.6 L GAS
    2010-2011 Chevrolet CamaroLS, LT6 Cyl 3.6 L GAS
    2010-2012 Chevrolet TraverseLS, LT, LTZ6 Cyl 3.6 L GAS
    2010-2012 GMC AcadiaDenali, SL, SLE, SLT6 Cyl 3.6 L GAS
    2010 Saturn OutlookXE, XR6 Cyl 3.6 L GAS
    Warning: California's Proposition 65
  • Customer Questions & Expert Answers

    Q:
    Is this 12612349 designed for my car? Posted by ChevyPartsGiant Specialist
    A:
    Please Select Your Vehicle model to see if part number 12612349 is suitable before ordering.
    Posted by ChevyPartsGiant Specialist
    Q:
    How to replace the Engine Oil Dipstick Tube on Cadillac SRX? Posted by Customer
    A:
    First turn on the ignition off and pull out the oil level indicator from its position on the oil level indicator tube before beginning the replacement process. Before the next step starts remove the oil level indicator tube bolt then raise the vehicle. Follow this procedure by removing the Knock Sensor alongside the heat shield clip from the oil level indicator tube. After lowering the vehicle observe the position of the secondary (small square) heat shield. The oil level indicator tube must be pulled up through the exhaust manifold to remove it. When replacing only the oil level indicator tube seal the technician needs to discard the previous seal. The installation requires positioning the secondary heat shield precisely as it was positioned during removal on the oil level indicator tube. Use the tube to raise the vehicle and afterward reinstall the Knock Sensor on completion of installation of the oil level indicator and tube. As the final step lower the vehicle after attaching the heat shield clip onto the oil level indicator tube.
    Posted by ChevyPartsGiant Specialist
    Q:
    How to replace the Dipstick Tube on Chevrolet Traverse? Posted by Customer
    A:
    Start the replacement process for the oil level indicator tube by taking away the fuel injector sight shield. Start by removing the oil level indicator from its tube through the indicator tube before loosening the bolt surrounding it. Use care to lift the oil level indicator tube from the Exhaust Manifold through its entire length. The procedure requires discarding the old seal only when replacing the oil level indicator tube seal. The installation requires putting a new seal on the oil level indicator tube before you place it in position. Follow up this step by installing the oil level indicator tube bolt until torque reaches 10 nm (89 lb in). Complete the installation by putting back the fuel injector sight shield followed by re-installing the oil level indicator inside its tube.
    Posted by ChevyPartsGiant Specialist
    Q:
    What is the final step in the replacement process for the 2010 Buick LaCrosse? Posted by Customer
    A:
    Install the oil level indicator tube bracket bolt and tighten it to 10 Nm (89 lb in).
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Dipstick Tube
    Q:
    What should be done with the heat shield clip for the 2009 Cadillac CTS? Posted by Customer
    A:
    Take off the heat shield clip from the oil level indicator tube before lowering the vehicle.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Dipstick Tube
    Q:
    What should be done after removing the fuel injector sight shield for the 2010 Cadillac CTS? Posted by Customer
    A:
    Take out the oil level indicator tube bracket bolt and slide the oil level indicator and tube out from the lower crankcase hole.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Dipstick Tube
    Q:
    What should be done last in the process for the 2008 Cadillac SRX? Posted by Customer
    A:
    Attach the heat shield clip to the oil level indicator tube as noted during removal and lower the vehicle.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Dipstick Tube
    Q:
    What should be done after installing the oil level indicator and tube for the 2009 Cadillac STS? Posted by Customer
    A:
    Raise the vehicle again and reinstall the knock sensor.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Dipstick Tube
    Q:
    What is the installation process for the oil level indicator tube for the 2010 Cadillac STS? Posted by Customer
    A:
    Place the oil level indicator and tube back in position, followed by the engine splash shield.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Dipstick Tube
    Q:
    What is the next step after removing the tube bolt for the LP1, LY7 for the 2008 Cadillac STS? Posted by Customer
    A:
    Raise the vehicle, remove the knock sensor, and the heat shield clip from the tube, then lower the vehicle.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Dipstick Tube
    Q:
    What should be done after removing the engine splash shield for the 2009 Cadillac STS? Posted by Customer
    A:
    Lower the vehicle and extract the oil level indicator tube up through the exhaust manifold.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Dipstick Tube
    Q:
    What is the next step after removing the oil level indicator for the 2010 Chevrolet Camaro? Posted by Customer
    A:
    Remove the oil level indicator tube bolt.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Dipstick Tube
    Q:
    What is the next step after removing the oil level indicator tube bolt for the 2009 Cadillac CTS? Posted by Customer
    A:
    Remove the engine splash shield and lower the vehicle.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Dipstick Tube
    If you have any questions about this product, please don't hesitate to ask us. We will be happy to help you!

OEM GM Oil Tube 12612349 Designed for Proper Fit and Performance

Original OEM GM parts deliver superior quality and meet all performance standards needed for optimal automotive operation. The authentic part identified by 12612349 Oil Tube is available in the market under the name GM Dipstick Tube. This genuine product has a full warranty coverage from the manufacturer available at all authorized GM dealers throughout the United States. This part 12612349 Oil Tube fits certain Chevrolet Camaro, Traverse models, as well as GMC Acadia. Additionally, it is compatible with Cadillac CTS, SRX, STS and Buick Enclave, LaCrosse models.
The original GM component designated by manufacturer part number 12612349 maintains top performance when functioning as the Tube, Engine Oil Level; Oil Dipstick Tube unit. The component 12612349 is constructed from durable material and its dimensions span 19.5 x 2.2 x 1.8 inches while weighing 0.50 Pounds. The Direct Replacement component is ready in New condition to ensure full compatibility with your vehicle system. This component receives the designation of Guide Tube; Tube. The part 12612349 has available replacement options. GM manufacturer provides a warranty that ensures reliable operation of this product. The Shipping Policy and Return Policy pages outline complete details regarding shipping procedures and return processes.
If you want to save money in the long run on maintenance and repairs, you should choose OEM products because they're of the top level of durability. Are you on the quest of finding GM parts, our site is worth a visit. We stock an endless selection of high-quality GM components including things like ignition coils all the way through to fan shrouds and all at prices that can not be matched. You have nothing to worry about because all our OEM parts are covered with a manufacturer warranty, which guarantees superior quality and value.