Make sure this part fits

GM 12494806
Wiper Blade Refill, Driver Side

2001-2007 GM

Customer Questions & Expert Answers (14)
GM 12494806 Wiper Blade Refill, Driver Side
  • Part Description
    Wiper, Windshield Wiper Blade
  • Position
    Driver Side
  • Manufacturer
    General Motors
  • Manufacturer's Notes
    This part is discontinued.
Make sure this part fits
  • Vehicle Fitment

    Year Make Model Trim Engine
    2002-2007 Buick RendezvousCX, CX Plus, CXL, CXL Plus, Ultra6 Cyl 3.4 L GAS, 6 Cyl 3.5 L GAS, 6 Cyl 3.6 L GAS
    2001-2005 Pontiac AztekBase, GT, Rally6 Cyl 3.4 L GAS
    Warning: California's Proposition 65
  • Customer Questions & Expert Answers

    Q:
    Is this 12494806 designed for my car? Posted by ChevyPartsGiant Specialist
    A:
    Please Select Your Vehicle model to see if part number 12494806 is suitable before ordering.
    Posted by ChevyPartsGiant Specialist
    Q:
    How do you remove the rear wiper blade element for the 2006 Buick Rendezvous? Posted by Customer
    A:
    First, remove the rear wiper blade from the rear wiper arm, then take out the rubber wiper element from the element vertebra, followed by removing the element vertebra and end cap from the rear wiper blade.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Wiper Blade
    Q:
    What is the procedure for securing the rear wiper arm for the 2007 Buick Rendezvous? Posted by Customer
    A:
    Install the rear wiper arm onto the rear wiper motor spindle, then secure it by installing the rear wiper arm nut, tightening it to 25 N.m (18 lb ft).
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Wiper Arm
    Q:
    What is the first step in the installation process for the 2005 Buick Rendezvous? Posted by Customer
    A:
    Attach the wiper blade onto the wiper arm.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Wiper Arm
    Q:
    How do you secure the rear wiper arm for the 2004 Buick Rendezvous? Posted by Customer
    A:
    Secure it with the rear wiper arm nut, tightening it to 25 N.m (18 lb ft).
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Wiper Arm
    Q:
    How do you remove the wiper blade for the 2007 Buick Rendezvous? Posted by Customer
    A:
    Push in the button of the wiper blade clip to remove the wiper blade from the inside radius of the wiper arm, then bring the wiper arm out through the opening in the wiper blade.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Wiper Blade
    Q:
    What should be done after removing the wiper arm for the 2003 Buick Rendezvous? Posted by Customer
    A:
    Remove the wiper blade from the wiper arm and clean the knurls of the wiper transmission drive shaft with a wire brush.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Wiper Arm
    Q:
    What is the final step in the process for the 2002 Buick Rendezvous? Posted by Customer
    A:
    Attach the rear wiper blade back onto the rear wiper arm.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Wiper Blade
    Q:
    What should you ensure during the installation of the wiper blade element for the 2007 Buick Rendezvous? Posted by Customer
    A:
    Ensure the wiper blade claws remain in the rubber claw channel of the wiper blade element and do not contact the metal spline of the wiper blade element.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Wiper Blade
    Q:
    How do you prepare the wiper transmission pivot shaft for installation for the 2006 Buick Rendezvous? Posted by Customer
    A:
    Clean the knurls of the wiper transmission pivot shaft with a soft wire brush.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Wiper Arm
    Q:
    What should be done for the passenger side wiper arm for the 2007 Buick Rendezvous? Posted by Customer
    A:
    Do the same for the passenger side wiper arm blade tip against the driver side target mark.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Wiper Arm
    Q:
    How do you position the wiper arms during installation for the 2002 Buick Rendezvous? Posted by Customer
    A:
    Hold the measuring device at 90 degrees (perpendicular) to the wiper blade tip and measure the distance from the wiper blade tip to the solid edge of the windshield blackout, positioning the wiper arms at 147 mm (5.79 in) above the glass blackout for the LH side and 123 mm (4.84 in) below the glass blackout for the RH side.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Wiper Arm
    Q:
    What is the first step for installation of the new wiper blade for the 2005 Buick Rendezvous? Posted by Customer
    A:
    Insert the hook of the wiper arm through the opening in the wiper blade.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Wiper Blade
    Q:
    What is the final step after checking the wiper blade element for the 2004 Buick Rendezvous? Posted by Customer
    A:
    Reinstall the wiper blades onto the wiper arms.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Wiper Blade
    If you have any questions about this product, please don't hesitate to ask us. We will be happy to help you!

OEM GM Wiper Blade Refill, Driver Side 12494806 Designed for Proper Fit and Performance

Original OEM GM parts deliver superior quality and meet all performance standards needed for optimal automotive operation. The authentic part identified by 12494806 Wiper Blade Refill, Driver Side is available in the market under the name GM Windshield Wiper, Wiper Arm, Wiper Blade. This genuine product has a full warranty coverage from the manufacturer available at all authorized GM dealers throughout the United States. This part 12494806 Wiper Blade Refill, Driver Side fits certain Buick Rendezvous models, as well as Pontiac Aztek models.
The original GM component designated by manufacturer part number 12494806 maintains top performance when functioning as the Wiper, Windshield Wiper Blade unit at its Driver Side. The component 12494806 is constructed from durable material and its dimensions span 27.2 x 1.1 x 0.6 inches while weighing 0.60 Pounds. The Direct Replacement component is ready in New condition to ensure full compatibility with your vehicle system. This component receives the designation of Wiper Blade Insert. The part 12494806 has available replacement options. GM manufacturer provides a warranty that ensures reliable operation of this product. The Shipping Policy and Return Policy pages outline complete details regarding shipping procedures and return processes.
If you want to save money in the long run on maintenance and repairs, you should choose OEM products because they're of the top level of durability. Are you on the quest of finding GM parts, our site is worth a visit. We stock an endless selection of high-quality GM components including things like ignition coils all the way through to fan shrouds and all at prices that can not be matched. You have nothing to worry about because all our OEM parts are covered with a manufacturer warranty, which guarantees superior quality and value.