GM 19244683
Washer Pump, Rear

First lift and stabilize the hood before draining the washer solvent vessel. Disconnect all electrical links and fluid lines from the washer pumps and pull out the screw locking the solvent bottle to the vehicle and the bottle itself. Take away the washing pump parts and grommets from the solvent storage compartment. Follow the fastener precaution directions when you put washer pumps and grommets onto the solvent container during installation. Secure the solvent container back onto the vehicle by screwing it in place then tightening to 3 N.m (27 lb in). Attach washer pump and electrical units to their proper spots before adding new washer fluid to the reservoir and closing the hood.

You need to take away the washer solvent container before removing the washer pumps from their reservoir. Reinsert the washer pumps into their proper positions in the reservoir after installing them there.

Begin by detaching the washer solvent container from the vehicle and then removing the washer pumps from inside. When replacing the windshield washer pump(s), put the damaged pump(s) back into the washer solvent tank and mount the tank back inside the vehicle.

Begin by detaching the washer solvent container from the vehicle and then removing the washer pumps from inside. When replacing the windshield washer pump(s), put the damaged pump(s) back into the washer solvent tank and mount the tank back inside the vehicle.

Taking out the battery tray and battery before handling the interior wheel compartment begins the windshield washer pump replacement process. Unplug the electrical connector from the washer pump and washer solvent level sensor before removing the washer hose from the pump. Take out the washer solvent container by removing its upper and lower bolts. Place the washer solvent container back into the vehicle and fasten the lower bolts by tightening them to 9 n.m whereas the upper bolt requires the same torque setting. Differentiate power to the washer pump and the washer solvent sensor before connecting new washer hose delivery. Put the battery tray and battery inside alongside the inner wheel housing.

You have to first eliminate the washer solvent container before taking out the washer pump(s) from the tank reservoir. You can install the washer pump system by returning the pump to the reservoir and putting the washer solvent container back.

Begin by taking off the washer solvent container followed by unhooking the washers and extracting the pump from this container. Install new washer pumps into the solvent container and reconnect hoses before putting in the washer tank.

For servicing or repairing the Windshield Washer Pump, take out the washer solvent container, then let go of the washer hose(s) and bring out the washer pump(s). First, put the washer pump(s) into the solvent container, then connect the washer hose(s) and finally install the solvent container.

The Windshield Washer Pump needs replacement through a stepwise process that starts by taking out the washer solvent container followed by undoing the washer pumps from their reservoir. Put the washer pumps into the reservoir and fit the washer solvent container back in place.

You need to take off the washer solvent container before working on the Windshield Washer Pump. Take all washer pumps out from the reservoir. After placing washer pumps into their storage tank you can restore the washer solvent container.

Place the washer pumps back into the reservoir.

Connect the washer hose to the pump.

Fill the washer solvent container with washer solvent and close the hood.

Fill the washer solvent container with washer solvent and close the hood.

Fill the washer solvent container with washer solvent and close the hood.

Open the hood and drain the washer solvent from the washer solvent container.

Remove the washer solvent container.

Reinstall the washer solvent container.

Remove the washer solvent container.

Refill the washer solvent in the solvent container and close the hood.

Connect the washer hose(s).

Place the washer pumps back into the reservoir.

Place the washer pumps and grommets onto the solvent container, ensuring to adhere to the Fastener Notice in Service Precautions.

Attach the pump to the retainer on the solvent container.

Place the washer pumps back into the reservoir.

Take out the washer pumps from the reservoir.

Disconnect the electrical connector from the washer pump and the washer solvent level sensor.

Install the pump into the sealing grommet and secure it to the retainer on the solvent container.

First, remove the washer solvent container.

Remove the washer pump from the washer solvent container.

Disconnect the rear washer pump electrical connector and the rear washer pump hose.

Reconnect the washer hose to the pump.

First, remove the washer solvent container.

Reconnect the hose and the electrical connector to the washer pump.

Take the pump out of the sealing grommet.

Reconnect the front washer pump hose and the electrical connector.

Position the seal in the washer solvent container, pressing it in until fully seated.

First, remove the washer solvent container.

Remove the screw and the solvent container from the vehicle.

The Fastener Notice in Service Precautions.

Place the washer pumps back into the reservoir.

Take out the washer pumps from the reservoir.