GM 89025062
Washer Pump

You can start replacing the windshield washer pump after opening the hood and letting washer solvent drain from its container. Take off the right fender cover first then disconnect the washer pump electric connection and tubing. Use a small flat-blade tool to unplug the washer pump from the solvent container before taking out the seal with the same tool from the container. Directly apply the new seal to the washer solvent container before fastening the washer pump onto place. Connect the washer pump electrical parts and hose while putting back the right front fender liner. Refill the washer solvent container with washer cleaning liquid and complete the process by closing the hood.

Begin the Windshield Washer Pump service by draining the washer solvent tank and taking out the wheelhouse extension on the right front side. Open the washer pump compartment to disconnect both hose and electrical wires then take out the pump from the solvent tank. Install the washer pump into the washer solvent container and restore power to the pump while attaching the washer hose. Then put back the wheelhouse extension. Complete the washing system by pouring fluid into the container.

Start re-replacement by emptying the washer solvent tank. Unblock the fascia extension from the right side and disconnect the wash hose plus electronics at the washer pump base. As a next step take the washer pump out of the washer solvent container. Begin by placing the new washer pump into the washer solvent storage area before connecting the electrical and washer hose connections to it. Reattach the right front fascia part and complete the washer solvent tank.

You should take off the front tender liner before replacing the windshield washer pump. Take the washer pump out of the washer solvent container. First detach both the electrical harness and hose from the washer pump before sliding the top unit away from the side to remove the entire pump. Extract the washer pump seal from the container with its washer fluid. Start the procedure by placing the new washer pump seal into the washer solvent container then insert the washer pump from the top first into the side before ending with the inlet. Insert the electrical part and hose back into the washer pump while placing the front fender liner back in its proper position.

Start your changes by opening the hood to drain washer solvent from the solvent container. Detach both the electrical cable and the hose from the front washer pump. Use a thin screwdriver to take out the front washer pump from its holding space in the washer solvent container. Set the front washer pump into place directly on the washer solvent container and push firmly until it clicks. Attach the front washer hose to the front washer pump followed by plugging in its electrical connector. Add washer solvent to the storage tank then lock the enclosure.

You need to empty the washer solvent reservoir before starting the windshield pump replacement. Start by taking out the right front wheelhouse piece before separating the washer line hose and electronic link from the washer pump. Pull the washer pump out of its storage position in the washer solvent container. Put the washer pump back in its solvent container and connect both the electrical connector and washer hose to the pump. Install the right front wheelhouse extension afterward then top off the washer solvent container.

Draining washer solvent from the tank is the first step to access the windshield washer pump when replacing it with the front fender liner removed. Take the washer pump electrical wire out from its port and remove its working hose. Insert a small flat-blade tool to take out the washer pump from the washer solvent container and then extract the seal from the container using the same tool. Insert the seal into the washer solvent container before placing the washer pump in position ensuring complete seating. Plug in the washer pump wires and hose before you put back the front fender panel and fill the washer solvent tank with washer solvent.

You need to take away the washer solvent container before removing the washer pumps from their reservoir. Reinsert the washer pumps into their proper positions in the reservoir after installing them there.

The Windshield Washer Pump needs replacement through a stepwise process that starts by taking out the washer solvent container followed by undoing the washer pumps from their reservoir. Put the washer pumps into the reservoir and fit the washer solvent container back in place.

You must disconnect both connectors from the Washer Pump and the solvent sensor before removing the washer tube from it. First you must remove the A/C Accumulator before taking out the two nuts and screw with washer solvent container. Take both components of the washer solvent container including the Washer Pump and grommet. Also remove the solvent level sensor switch and its grommet. Set the grommet and solvent level sensor switch into the washer solvent container then push the Washer Pump all the way into the container seal. After installing the Washer Pump and grommet into the washer solvent container use two nuts and screw to fasten it before tightening each nut to 6 n.m (53 lb in). Install the A/C Accumulator and link electrical wires to the Washer Pump and solvent level sensor switch. Connect the washer hose to its pump and fill the washer solvent equipment with new solvent.

Start your work on the Windshield Washer Pump by taking out the front fender liner. Take off the washer pump from the washer solvent container by first pulling the top from the side and then pulling the pump out completely. Afterwards disconnect the electrical connector and the hose from the washer pump. You need to take out the washer pump grommet from the washer solvent container. Insert the washer pump grommet into the washer solvent container before pushing the washer pump wholly into the container from the inlet end and snapping the top into place on the container side. Reattach the electrical wires and hose to the washer pump before putting back the front fender panel.

First remove the washer solvent container before taking out the washer pumps from their reservoir. Return the washer pumps into the reservoir space while also restoring the washer solvent tank.

Begin by taking off both the coolant recovery reservoir and the washer solvent container. Unplug the washer hose connections and take washer pumps out from the solvent tank. Start by putting the washer pumps in the solvent container then join the washer piping. You should install washer solvent container first and then coolant recovery reservoir in that order.

The Windshield Washer Pump needs replacement through a stepwise process that starts by taking out the washer solvent container followed by undoing the washer pumps from their reservoir. Put the washer pumps into the reservoir and fit the washer solvent container back in place.

Before removing the pump, you need to disconnect the wire connector and hose from the washer pump; then lift the pump from the solvent container. To install, place the washer pump into the washing solvent container, making sure it is all the way in and its cover has pushed into the side. Then, attach the connectors to the pump, add the washer solvent, turn on the system and see if it is working as expected.

Start by taking out the washer solvent from its container to replace the Windshield Washer Pump. Take the washer pump out of its position by first detaching the electrical connection from it. Disconnect the washer hose from its location on the washer pump next. Start the installation by fitting the washer hose to the washer pump before reinserting the washer pump into the washer solvent container. Plug the electrical connector into the washer pump and then replace washer solvent into the machine tank.

Begin the windshield Washer Pump service by taking off the two nuts that secure the washer solvent reservoir and the hose retention clamp from the frame rail stud. Pull out the washer solvent reservoir from its wheelhouse location and detach both electrical plug and washer hose at the Washer Pump it serves. Separate the washer solvent reservoir and empty washer solvent from its storage tank. Take out the Washer Pump assembly and its contents from the reservoir through its fluid level sensor. Swerve the fluid level sensor into the washer solvent reservoir before adding the Washer Pump and seal into their proper positions. Fit the electrical circuit and washer hose to the pump to connect them to the fluid level sensor. Put the washer solvent reservoir onto studs at both frame rail and wheelhouse positions and thread the hose retention clamp onto the frame rail stud. Secure the washer solvent reservoir using its attaching nuts until they reach 7.5 n.m (66 lb in) torque. Add washer solvent into the fluid container at the end of the process.

You need to take out the washer solvent from both the washer solvent container and the left front fender before working on the Windshield Washer Pump. Pull apart the washer pump connections to both the electrical wire plug and hose. A flat-bladed tool helps detach the washer pump from its wash solvent container and extract the seal from the same container. After positioning the seal into the washer solvent container you must press it in until it touches bottom. Next put the washer pump into the container and press until it is also seated. Reassemble the washer system by joining the hose to the pump and reconnecting electrical power before putting back the left fender and filling washer solvent into the container.

Start the process by opening and supporting the hood then taking out both components supporting the fender plus the bolt that secures the washer solvent container. From within the washer solvent container lift it higher to gain washer pump access and disconnect both electrical connector and washer hose from the washer pump. Put a washer pump cap on to stop solvent leakage. Lower the washer solvent container from the vehicle and empty it into a suitable container before you take apart the washer pump and washer solvent container cap. Insert the new washer pump unit into the washer solvent container and twist on the cover to retain it. Secure the electrical and washer hose lines to the new washer pump. Align the washer solvent container into its chassis mounting holes and fasten it with the bolt while turning for 10 N.m (89 lb in) torque. Replace the upper fender support while filling washer solvent into the container and finishing up with hood closure.

To fix the windshield washer pump begin by lifting the hood and securing it. Then you will need to remove both the upper fender support and bolt from the washer solvent container. Empty the washer solvent container to see its washer hose and electrical connection. Disconnect the hose and electrical lead from the pump then snap a cap onto the pump to hold the fluid inside. Take the washer solvent container off the car then empty its contents into a suitable receptacle before taking out the washer pump and cap from the washer tank. Simply put the new washer pump inside the washer solvent container then attach the cap. Apply the electrical connector and washing hose to the new washer pump. Fit the washer solvent container into chassis mounting holes and screw it with a bolt to a torque setting of 10 N.m (89 lb. in.). Replace and secure the upper fender support while adding washer solvent to its container then shutting the hood.

Open and safety-secure the hood before you take out the washer solvent bolt from its holder. Unscrew the washer solvent container until the washer hose and electrical connector are visible. Then disconnect both components from the washer pump and put a cap on the pump side to stop washer solvent escape. Take out the washer solvent container and drain the liquid into a proper container before separating the washer pump from it and its cap. Place the new washer pump within the washer solvent container and fasten it using the cap. Connect the washer hose and electrical connector from the brake switch to the washer pump. Insert the washer solvent container into chassis location points and fasten it with a bolt tightened to 10 N.m (89 lb in). Install the upper fender support then put washer solution into the container and shut the hood.

To work on the Windshield Washer Pump you need to take out both washer solvent from its container and from the left front fender liner first. Remove the electrical plug and washer outlet tube from their connectors. Apply your flat-bladed tool to take out the washer pump from the washer solvent container then use it again to discard the seal. Push the seal firmly into the washer solvent container before placing the washer pump inside and making sure it sits tightly. Reinsert the washer hose and electrical pump connectors before putting back the left front fender panel and loading washer solvent into the reservoir.

First drain washer solvent from the reservoir container before removing the front fender liner. Take off the washer pump connections from power and water supply. Insert a small flat tool to discharge the washer pump from its solvent holder then utilize the instrument to extract the seal from the solvent container. Set the new seal into the washer solvent container using force until it fits correctly then put the new washer pump into the container following the same pressing method. Plug back the washer pump electrical wire and hose then put back the front fender lining before placing washer solvent inside the washer solvent container.

Start your windshield washer pump replacement by removing the front fender liner. Detach the washer pump electrical connection plus the hose. After that pull the top part out from the side and gently remove the washer pump. Pull out the washer seal from its compartment in the washer solvent hose. Start the process by inserting the washer pump seal into the washer solvent container then push the washer pump until it seats entirely at its holder. Close the system by connecting power and hose components back to the washer pump then replace the front fender panel.

To replace the Windshield Washer Pump start by unplugging its electrical connection and removing the washer hose. Take the top part of the washer pump out through the washer solvent container and uninstall the pump from the container before removing its grommet. Insert the washer pump grommet into the washer solvent container opening while fitting the pump back into the container until the top lodges against its side. Reassemble the washer hose and electrical connection to the washer motor.

The procedure to fix the Washer Pump starts with removing the front fender panel. Unplug the electrical connection and hose from the washer pump before you pull out the washer pump from its solvent holder at the top by removing it from the side first. Take out the washer grommet from the washer solvent container. First stick the washer pump grommet into the washer solvent holder before pushing the washer pump inlet into the container until full and plugging the top into the side. Secure the electrical system and hose linkage to the washer pump before putting back the front fender liner.

The Windshield Washer Pump needs replacement through a stepwise process that starts by taking out the washer solvent container followed by undoing the washer pumps from their reservoir. Put the washer pumps into the reservoir and fit the washer solvent container back in place.

You need to take away the washer solvent container before removing the washer pumps from their reservoir. Reinsert the washer pumps into their proper positions in the reservoir after installing them there.

The Windshield Washer Pump needs replacement through a stepwise process that starts by taking out the washer solvent container followed by undoing the washer pumps from their reservoir. Put the washer pumps into the reservoir and fit the washer solvent container back in place.

The Windshield Washer Pump needs replacement through a stepwise process that starts by taking out the washer solvent container followed by undoing the washer pumps from their reservoir. Put the washer pumps into the reservoir and fit the washer solvent container back in place.

Taking out the battery tray and battery before handling the interior wheel compartment begins the windshield washer pump replacement process. Unplug the electrical connector from the washer pump and washer solvent level sensor before removing the washer hose from the pump. Take out the washer solvent container by removing its upper and lower bolts. Place the washer solvent container back into the vehicle and fasten the lower bolts by tightening them to 9 n.m whereas the upper bolt requires the same torque setting. Differentiate power to the washer pump and the washer solvent sensor before connecting new washer hose delivery. Put the battery tray and battery inside alongside the inner wheel housing.

You need to take away the washer solvent container before removing the washer pumps from their reservoir. Reinsert the washer pumps into their proper positions in the reservoir after installing them there.

You need to take away the washer solvent container before removing the washer pumps from their reservoir. Reinsert the washer pumps into their proper positions in the reservoir after installing them there.

Before working on the windshield Washer Pump you must take out the master cylinder and put it aside without separating the brake lines. With the washer solvent bolt out you can handle the container up to reach the washer hose and electrical connector. Pull off the washer hose and electrical connection from the Washer Pump before taking out the washer solvent container. Detach the Washer Pump component from its storage in the washer solvent reservoir. After replacing both parts into the washer solvent container reattach the electrical connector and washer hose to the Washer Pump followed by fitting the tank into the chassis location. Secure the washer solvent container using the bolt until it reaches torque settings of 10 n.m (89 lb in). Replace the master cylinder afterwards.

You must empty the washer solvent from its container before starting the replacement work. You should disconnect both electrical and hose connections from the washer pump at the rear of the vehicle, and unbutton it from its socket. Apply a small flat tool to detach the rear washer pump from the washer solvent container followed by removing the seal from the washer solvent container with the same tool. Insert the seal into the washer solvent container and push until it reaches full position followed by putting the rear washer pump in place. Apply similar pushing force until the pump is set. Attach the rear washer pump hose and electricity connection. Finally pour washer solvent into the washer solvent container.

The Windshield Washer Pump needs replacement through a stepwise process that starts by taking out the washer solvent container followed by undoing the washer pumps from their reservoir. Put the washer pumps into the reservoir and fit the washer solvent container back in place.

You should first open the hood and support it, then take out the washer solvent container. Pull outward on the top of the pump to take it off the container, then use 2 flat-bladed tools to gently lift the sides and carefully free the pump from the grommet. Take out the Washer Pump from the container and get rid of both the pump and the grommet. To put the Washer Pump in place, drop the grommet into the washer solvent container and put some washer solvent on the pump's intake spout for smooth installation. Press the pump into the grommet, make sure the top of the pump is fastened to the washer container, put back the washer solvent container, and close the hood.

Start servicing and repairing the Windshield Washer Pump by removing washer solvent from its container. You must disconnect both electrical links and fluid lines from the washer pumps. Take out the solvent container and screw and remove the washer pumps and grommets from it. Before proceeding start by placing washer pumps and grommets onto the solvent container. Fasten the solvent container onto the vehicle by screwing and tightening it to 3 N.m (27 lb in). Replug the electrical wires and hose lines to the washer pumps before filling the washer solvent into the storage tank.

The Windshield Washer Pump needs replacement through a stepwise process that starts by taking out the washer solvent container followed by undoing the washer pumps from their reservoir. Put the washer pumps into the reservoir and fit the washer solvent container back in place.

Open the hood to reach the washing system's components. Support the hood to avoid accidents. Disconnect the upper fender support and washer solvent container bolt. You can pull up the washer solvent container to reach the washer hose and electrical connector. Disconnect them at the washer pump and place a cap on the opening to contain the solvent. Take the washer solvent container out of the car. Put the solvent into a safe container. Then separate the washer pump from the container and its cap. Insert the new washer pump into the washer solvent container then lock it with the container cap. Position the washer solvent container into chassis holes then attach its bolt and washer hose to the new washer pump while connecting the electrical connector. Tighten the bolt to 10 Nm (89 lb in). Put back the upper fender support while filling the washer solvent container and shutting the hood.

You need to take away the washer solvent container before removing the washer pumps from their reservoir. Reinsert the washer pumps into their proper positions in the reservoir after installing them there.

The Windshield Washer Pump needs replacement through a stepwise process that starts by taking out the washer solvent container followed by undoing the washer pumps from their reservoir. Put the washer pumps into the reservoir and fit the washer solvent container back in place.

Start by opening and securing the hood before taking off the upper support and bolt from the washer solvent holder. When you lift the washer solvent container you can reach the washer hose and electrical connector. Disconnect them both from the washer pump and place a cap on the pump to save the solvent. Take out the washer solvent container from the vehicle and put its contents into a suitable container. Afterwards remove the washer pump from both the container and its cap. Set the new washer pump into the washer solvent container then screw on its cap. Hook the electrical connector and washer hose to the new washer pump then locate the washer solvent container into chassis clips and bolt it down with 10 N.m (89 lb in). Replace the upper fender support and begin this step by adding washer solvent into the containing container.

Connect the rear hose to the rear washer pump and then connect the rear washer pump electrical connector.

Install the washer pump back into the washer solvent container.

Disconnect the washer hose from the pump.

Position the front washer pump into the washer solvent container, pressing in until fully seated.

Connect the rear hose to the rear washer pump and then connect the rear washer pump electrical connector.

Install the washer pump onto the container.

Gently pry the washer pump from the container and remove it along with the washer pump grommet.

Reconnect the electrical connector and the washer hose to the washer pump.

Remove the electrical connectors from the washer pump and the solvent level sensor switch, followed by the washer hose from the washer pump.

Remove the right front fascia extension.

Place the washer pumps and grommets onto the solvent container.

Connect the washer pump hose and the electrical connector.

First, remove the washer solvent container.

Place the washer pump back into the washer solvent container, ensuring it is pushed down completely and the top is secured against the side of the container.

The electrical connectors and hoses from the washer pumps.

Remove the screw securing the solvent container to the vehicle and take out the washer pumps along with the grommets from the solvent container.

Remove the washer pump from the washer solvent container.

Position the washer pump seal in the washer solvent container, pressing it in until fully seated.

Connect the electrical connector and washer hose to the washer pump, then connect the electrical connector to the fluid level sensor.

Reinstall the washer solvent container.

Remove the washer pump seal from the container.

Reinstall the washer solvent container onto the vehicle.

Remove the bolt from the washer solvent container and lift it enough to access the washer hose and electrical connector.

Reinstall the washer solvent container onto the vehicle.

Ensure that the washer pump is pushed completely into the container seal.

Reinstall the washer solvent container.

Connect the hose to the washer pump.

Remove it from the vehicle and drain the washer solvent into a suitable container.

Reinstall the inner wheel housing and the battery along with the battery tray.

Reconnect the front washer pump hose and the electrical connector.

Disconnect the washer hose from the pump and carefully pull the pump from the retainer to remove it from the solvent container.

Place a new washer pump grommet into the washer container and lubricate it with clean washer solvent.

Reinstall the washer solvent container onto the vehicle.

First, remove the washer solvent container.

Use a small flat-bladed tool to remove the washer pump from the washer solvent container.

Position the seal in the washer solvent container, pressing it in until fully seated.

Reinstall the washer solvent container.

Remove the washer pump(s) from the reservoir.

Reconnect the washer hose(s).

Install the washer solvent container.

Place the washer pumps back into the reservoir.

Take out the washer pump(s) from the reservoir.

The electrical connectors and hoses.

Disconnect the washer hose and electrical connector from the washer pump.