Other Name: Arm, Windshield Wiper Transmission; Front Arm
Position: Driver Side
Replaces: 25879117
Fits the following Chevrolet Models:
Avalanche | 2008-2013 | Black Diamond LS, Black Diamond LT, Black Diamond LTZ, LS, LT, LTZ | 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L GAS
Suburban 1500 | 2008-2014 | LS, LT, LTZ | 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L GAS
Suburban 2500 | 2008-2013 | LS, LT | 8 Cyl 6.0 L FLEX, 8 Cyl 6.0 L GAS
Tahoe | 2008-2014 | Hybrid, LS, LT, LTZ | 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L FULL HYBRID EV-FLEX (FHEV), 8 Cyl 6.0 L FULL HYBRID EV-GAS (FHEV), 8 Cyl 6.2 L FLEX, 8 Cyl 6.2 L GAS
Other Name: Arm-Windshield Wiper; Front Arm; Arm, Windshield Wiper Arm
Position: Passenger Side
Replaces: 22873207, 25788778
Fits the following Chevrolet Models:
Equinox | 2010-2017 | L, LS, LT, LTZ, Premier | 4 Cyl 2.4 L FLEX, 4 Cyl 2.4 L GAS, 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS
Q: How to Properly Service and Repair a Wiper Arm on Chevrolet Colorado?
A: Start your task by opening the hood to remove Wiper Arm nut caps before throwing them away. Use your hands to remove the Wiper Arm nut from the arm itself. When Wiper Arm does not loosen from shaft by rocking use j 39637 (Wiper Arm Puller) to take it off. Remove the Wiper Blade from the Wiper Arm and wipe the shaft knurls with a soft brush. Fit the Wiper Blade to the new Wiper Arm then pull the Wiper Blade off the windshield and put on the Wiper Arm to the Wiper Arm support shaft. Position the Wiper Blade tip directly on the round dot inside the windshield blackout area while placing driver side blade tip at driver side alignment dot and passenger side blade tip at passenger side alignment dot. Secure the Wiper Blade with your hands and fasten the Wiper Arm nut by pressing it to 33-38 nm (24-28 lb ft). Put the fresh Wiper Arm nut covers in place and shut the hood.
Q: How to service and repair the wiper arm on Chevrolet Malibu?
A: Before working on the Wiper Arm you need to mark where the blade rests on the windshield before lifting the hood and disconnecting the washer hose. Pull off the outer cover to reach the Wiper Arm nut. Disconnect the nut from its place. When Wiper Arm rocking fails to break the Drive Shaft bond, a battery terminal puller should be used to remove it. Shake the Wiper Arm to disconnect it from the Drive Shaft and brush off the Drive Shaft knurls using a wire brush. Line up the Wiper Arm over the position mark then install it onto the Drive Shaft. Place the Drive Shaft nut then fasten it to 25 n.m (18 lb ft) torque. Finally attach the washer hose cover and Drive Shaft nut. Lower the hood first then remove the windshield marker before testing the wiper operation.
Q: How to replace the rear wiper arm on Chevrolet S10?
A: Using tools and basic components, replace your back wiper arm by setting it into park position first. Uninstall the washer hose from vehicle port and then take off the cap and nut from the wiper arm. Remove the wiper arm from the motor shaft. Set the new wiper arm on top of the wiper motor shaft in the park position when it naturally stops against the park ramp. Set the wiper arm in place then fasten the nut with torque 23 N.m (17 lb ft). Replace the washer hose into its original connection point before putting back the wiper arm cap.