ChevyParts
My Garage
My Account
Cart
OEM 2000 Chevrolet Camaro Brake Calipers
Caliper- Select Vehicle by Model
- Select Vehicle by VIN
Select Vehicle by Model
orMake
Model
Year
Select Vehicle by VIN
For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).
5 Brake Calipers found
Product Specifications- Other Name: Caliper Assembly, Front Brake (Service); Brake Caliper; Caliper, Wheel Brake Cylinder/Caliper
- Position: Front Passenger Side
- Replaces: 18026159
- Item Weight: 6.30 Pounds
- Item Dimensions: 7.9 x 9.0 x 6.5 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 18042492
- Warranty: This genuine part is guaranteed by GM's factory warranty.
2000 Chevrolet Camaro Caliper, Front Driver Side Part Number: 18042491
Product Specifications- Other Name: Caliper Assembly, Front Brake (Service); Brake Caliper; Caliper, Wheel Brake Cylinder/Caliper
- Position: Front Driver Side
- Replaces: 18026158
- Item Weight: 6.10 Pounds
- Item Dimensions: 8.0 x 9.1 x 6.4 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 18042491
- Warranty: This genuine part is guaranteed by GM's factory warranty.
2000 Chevrolet Camaro Caliper, Rear Driver Side Part Number: 12455127
Product Specifications- Other Name: Housing Assembly, Rear Brake Caliper; Caliper Kit, Wheel Brake Cylinder/Caliper; Brake Caliper
- Position: Rear Driver Side
- Item Weight: 0.60 Pounds
- Item Dimensions: 7.8 x 7.8 x 6.8 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 12455127
- Warranty: This genuine part is guaranteed by GM's factory warranty.
- Product Specifications
- Other Name: Caliper Kit, Rear Brake; Brake Caliper; Caliper Kit, Wheel Brake Cylinder/Caliper
- Position: Rear Passenger Side
- Item Weight: 3.00 Pounds
- Item Dimensions: 7.1 x 7.8 x 6.6 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 12455128
- Warranty: This genuine part is guaranteed by GM's factory warranty.
2000 Chevrolet Camaro Overhaul Kit, Front Part Number: 18026160
Product Specifications- Other Name: Caliper Kit, Front Brake; Brake Caliper Repair Kit; Disc Brake Hardware Kit; Caliper Kit, Wheel Brake Cylinder/Caliper
- Position: Front
- Item Weight: 0.40 Pounds
- Item Dimensions: 6.6 x 5.6 x 0.7 inches
- Condition: New
- Fitment Type: Direct Replacement
- Require Quantity: 4
- SKU: 18026160
- Warranty: This genuine part is guaranteed by GM's factory warranty.
2000 Chevrolet Camaro Brake Calipers
With a comprehensive array of OEM 2000 Chevrolet Camaro Brake Calipers, from fuel pumps to door handles, our website is a one-stop-shop for your needs. All our genuine 2000 Chevrolet Camaro Brake Calipers are backed by the manufacturer's warranty and are offered at competitive prices in the market. Rest assured, you can shop with complete confidence.
2000 Chevrolet Camaro Brake Calipers Parts and Q&A
- Q: How to service and repair rear brake calipers on 2000 Chevrolet Camaro?A: Start repairs of the back brake caliper using all included replacement parts and applying brake fluid to rubber parts for better assembly. When removing hydraulic parts the brake system needs total or partial bleeding and brake pads must be changed together in axle pairs. Set up your workspace on a no-mineral-oil clean bench and work with dry torque values for unlubricated screws when following these instructions. Protect your fingers from the Piston by not putting them into the path while you use compressed air to prevent severe bodily harm. Begin by taking the brake caliper off the vehicle then push compressed air through the brake hose inlet fitting port to move the Piston to the brake cylinder. After disassembly start with removing the Piston boot and seal then switch to taking off the little screw cap and bleed screw of the caliper. Look for damaged details in both the brake caliper hole and Piston seal groove before deciding to replace the housing. Examine the surfaces where the Brake Caliper Bracket attaches for damage caused by corrosion or wear and install a new bracket when required. Use filtered and oil-free compressed air to dry brake caliper housing and mounting bracket surfaces after removing the Brake Pad residues. Also clean all parts except repair kit contents with denatured alcohol before air-drying them. Clear all tubes inside the brake caliper housing and bleeder valve. You should install and hand-tighten the brake caliper bleed screw at 12 nm until you are ready to install the bleed screw cap. Apply brake fluid to both the new Piston seal and the brake caliper bore seal groove before placing the seal past the groove edge without spinning it. Add brake fluid to both brake caliper assembly parts and seal them together ensuring the boot fits sufficiently into its designated areas. Apply lubrication and Piston installation steps one more time before putting the brake caliper onto its original position on the vehicle.
Related 2000 Chevrolet Camaro Parts
2000 Chevrolet Camaro ABS Sensor
2000 Chevrolet Camaro Brake Caliper Bracket
2000 Chevrolet Camaro Brake Caliper Repair Kit
2000 Chevrolet Camaro Brake Disc
2000 Chevrolet Camaro Brake Dust Shields
2000 Chevrolet Camaro Brake Proportioning Valve
2000 Chevrolet Camaro Hydraulic Hose
2000 Chevrolet Camaro Parking Brake Cable
2000 Chevrolet Camaro Wheel Bearing
2000 Chevrolet Camaro Wheel Hub
2000 Chevrolet Camaro Wheel Hub Bolt
2000 Chevrolet Camaro Wheel Speed Sensor