How to replace the LH Blend Door Actuator on 2001 Buick Century?

To replace the left air temperature actuator, you must remove the left instrument panel insulator and the knee bolster. Lift the actuator off after you pull off the left temperature actuator's electrical connectors and remove the mounting screws. For installation, place the new left air temperature actuator with slots of the electric actuator driver to align with the flats on the shaft, while putting the slot for the locating hole align with the locating pin on the HVAC module case. Push the actuator driver onto the shaft until it is seated with the mounting holes touching the mounting bolts of the HVAC Module case. Slide the actuator driver onto the shaft until it is fully seated, with the mounting holes flush against the mounting bolts on the HVAC module case. Screw in the mounting screws and secure with 1.5 N.m (13 lb in). Replace the knee bolster and the left insulator of the instrument panel. Reconnect the electrical connector to the actuator. Finally, re-calibrate the actuator.

OEM 2001 Buick Century Blend Door Actuator

Air Blend Door Actuator

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

3 Blend Door Actuators found

View related parts
2001 Buick Century Door Actuator
Part Number: 89018365
$194.60 MSRP: $349.06
You Save: $154.46 (45%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Actuator, Air Conditioner Control; HVAC Heater Blend Door Actuator; HVAC Blend Door Actuator; Temperature Door Actuator; Switch; Controller; Actuator; Actuator, A/C Vacuum Control; Actuator, A/C Control
- Replaces: 16163982
- Item Weight: 0.80 Pounds
- Item Dimensions: 6.2 x 4.2 x 4.2 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 89018365
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2001 Buick Century Submodels:
- Custom, Limited, Special Edition | 6 Cyl 3.1 L GAS
View related parts
2001 Buick Century Door Actuator
Part Number: 52487750
Product Specifications
- Other Name: Actuator Assembly, Mode Valve; HVAC Heater Blend Door Actuator; Controller; Actuator; Actuator, A/C Control
- Replaces: 52482059
- Item Weight: 0.70 Pounds
- Item Dimensions: 5.7 x 5.5 x 3.6 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 52487750
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2001 Buick Century Submodels:
- Custom, Limited, Special Edition | 6 Cyl 3.1 L GAS
View related parts
2001 Buick Century Door Actuator
Part Number: 52487593
Product Specifications
- Other Name: Actuator, Air Conditioner Control; HVAC Heater Blend Door Actuator; Controller; Actuator; Actuator, A/C Control
- Replaces: 52472510
- Item Weight: 0.50 Pounds
- Item Dimensions: 6.3 x 4.2 x 4.2 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 52487593
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2001 Buick Century Submodels:
- Custom, Limited, Special Edition | 6 Cyl 3.1 L GAS

2001 Buick Century Blend Door Actuator

With a comprehensive array of OEM 2001 Buick Century Blend Door Actuator, from fuel pumps to door handles, our website is a one-stop-shop for your needs. All our genuine 2001 Buick Century Blend Door Actuator are backed by the manufacturer's warranty and are offered at competitive prices in the market. Rest assured, you can shop with complete confidence.

2001 Buick Century Blend Door Actuator Parts Questions & Experts Answers

Q: How to replace the LH Blend Door Actuator on 2001 Buick Century?
A: To replace the left air temperature actuator, you must remove the left instrument panel insulator and the knee bolster. Lift the actuator off after you pull off the left temperature actuator's electrical connectors and remove the mounting screws. For installation, place the new left air temperature actuator with slots of the electric actuator driver to align with the flats on the shaft, while putting the slot for the locating hole align with the locating pin on the HVAC module case. Push the actuator driver onto the shaft until it is seated with the mounting holes touching the mounting bolts of the HVAC Module case. Slide the actuator driver onto the shaft until it is fully seated, with the mounting holes flush against the mounting bolts on the HVAC module case. Screw in the mounting screws and secure with 1.5 N.m (13 lb in). Replace the knee bolster and the left insulator of the instrument panel. Reconnect the electrical connector to the actuator. Finally, re-calibrate the actuator.