What tools are required to replace the drive pinion bearings on 8.6 and 9.5 inch axles on 2003 Cadillac Escalade?

The tools necessary in order to replace the drive pinion bearings on 8.6 and 9.5 inch axles; oh, and like all vehicles, those that are twenty feet long cost about the same to buy as an ordinary aircraft carrier-http://blogs.obscura.com/lostlabchallenge/home.b on line bakeka.february 2007. J7818 (Inner Bearing Race Installer), j8092 (Universal Driver Handle - 3/4 inch - 10), j8611 (Rear Pinion Bearing Race Installer), j8614-01 (Flange and Pulley Holding Tool), j22306 (Rear Pinion Cup Bearing Installer), j22912-01 (Split Plate Bearing Puller), j24433 (Pinion Cone and Side Bearing Installer), j36614 (Inner Pinion Bearing Installer), j45870 (Pinion Bearing Cup Installer), and j45871 (Pinion Bearing Remover). Start by lifting the vehicle and then removing the right part of theifferential assembly combining with the drive pinion from the axle. For 8.6 inch axle, take 32.151 around Pinion Bearing and the 32.150-1 in reversed position around the 32.151 to apply the pressure and press the bearing off. For the 9.5 inch and 11.5 inch axles, the use of the j22912-01 to press the bearing off. Take off the shim, and both the outer and inner Pinion Bearing cups from the axle housing using a hammer and brass drift. For the installation, the j8611-01 for the outer Pinion Bearing cup should be used on the 8.6 inch axle or one can employ j7818 for the 9.5 inch axle with j8092. For the inner pin ion bearing cup, use the bearing id: j45870 for the 8.6 in axle or the bearing id: j22306 for the 9.5 in axle with the bearing code: j8092. Measure the selective shim thickness and place it between the inner Pinion Bearing and the shoulder on the gear. Install inner Pinion Bearing using the j24433 or j36614 and press it on until cone seats on the pinion shim. Install a new collapsible spacer, lubricate the pinion bearings with axle lubricant, and install the outer Pinion Bearing into the axle housing. Replace yet another new pinion oil seal using the j22388 follow by replacing the pinion into the axle housing. Apply sealant gp, p/n: 12346004 (Canadian P/N: 10953480, or equivalent) to splines of the pinion yoke, and install the pinion yoke, aligning the marks done in removal. Tap in the pinion yoke onto the pinion shaft with a soft-headed hammer until a few threads are visible through the yoke place the washer and the new pinion nut. Tighten with the j8614-01 holding the pinion yoke to take up the pinion end play even though rotating the pinion while tightening to seat bearings. Check the rotating torque of the pinion by using an inch-pound torque wrench and it remains within 1.0 - 2.3 nm (10 - 20 inch lbs.) for used bearings or when used with new bearings-maintain a range of 1.7 - 3.4 nm (15 - 30 inch lbs.). If the torque is below the specification, keep on tightening the pinion nut tightening in small steps until you reach the right torque. After the specified torque is achieved, rotate the pinion a few times to guarantee the seating of the bearings, and check the torque again for any adjustments. Finally, installing the Differential assembly, lubricant the axle, and lowering the vehicle.

OEM 2003 Cadillac Escalade Pinion Bearing

Transmission Pinion Bearing

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

12 Pinion Bearings found

View related parts
2003 Cadillac Escalade Side Bearings
Part Number: 88943839
$48.83 MSRP: $144.56
You Save: $95.73 (67%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bearing, Differential Side Gear; Differential Bearing
- Replaces: 26091723
- Item Weight: 1.80 Pounds
- Item Dimensions: 4.7 x 4.7 x 1.6 inches
- Condition: New
- Fitment Type: Direct Replacement
- Require Quantity: 2
- SKU: 88943839
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2003 Cadillac Escalade Submodels:
- Base | 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L GAS
View related parts
2003 Cadillac Escalade Pinion Bearings
Part Number: 454021
$161.60 MSRP: $292.48
You Save: $130.88 (45%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bearing Assembly, Differential Drive Pinion Gear; Differential Pinion Bearing; Rear Pinion Bearing; Inner Pinion Bearing; Differential Drive Pinion; Rear Wheel Bearing.
- Item Weight: 3.50 Pounds
- Item Dimensions: 4.7 x 4.8 x 2.0 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 454021
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2003 Cadillac Escalade Submodels:
- Base | 8 Cyl 5.3 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 6.0 L GAS
View related parts
2003 Cadillac Escalade Side Bearings
Part Number: 11505123
$56.18 MSRP: $166.26
You Save: $110.08 (67%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bearing, Differential Side Gear; Differential Pinion Bearing; Differential Bearing; Bearing
- Item Weight: 1.60 Pounds
- Item Dimensions: 4.9 x 1.4 x 5.1 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 11505123
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2003 Cadillac Escalade Submodels:
- Base, Luxury, Platinum, Premium | 8 Cyl 5.3 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 6.0 L GAS, 8 Cyl 6.2 L FLEX, 8 Cyl 6.2 L GAS
View related parts
2003 Cadillac Escalade Pinion Bearings, Inner
Part Number: 457108
$55.00 MSRP: $154.36
You Save: $99.36 (65%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bearing, Differential Drive Pinion Gear Inner; Differential Pinion Bearing; Rear Pinion Bearing; Front Pinion Bearing; Inner Pinion Bearing; Differential Drive Pinion Bearings.
- Position: Inner
- Item Weight: 2.20 Pounds
- Item Dimensions: 4.9 x 1.5 x 5.0 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 457108
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2003 Cadillac Escalade Submodels:
- Base, Luxury, Platinum, Premium | 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L GAS, 8 Cyl 6.2 L FLEX, 8 Cyl 6.2 L GAS
View related parts
2003 Cadillac Escalade Wheel Bearing
Part Number: 9436881
$76.25 MSRP: $145.36
You Save: $69.11 (48%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Bearing, Differential; Differential Pinion Bearing; Differential Bearing; Axle Bearings; Shaft; Inner; Side; Differential Gear; Front Wheel; Rear Wheel; Nut.
- Item Weight: 1.70 Pounds
- Item Dimensions: 5.1 x 1.5 x 5.0 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 9436881
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2003 Cadillac Escalade Submodels:
- Base | 8 Cyl 5.3 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 6.0 L GAS
View related parts
2003 Cadillac Escalade Side Bearings
Part Number: 25824250
$72.20 MSRP: $140.14
You Save: $67.94 (49%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bearing, Differential Side Gear; Differential Pinion Bearing; Differential Bearing
- Replaces: 09418390, 9418390
- Item Weight: 1.20 Pounds
- Item Dimensions: 4.3 x 4.3 x 2.1 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 25824250
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2003 Cadillac Escalade Submodels:
- Base, Hybrid, Hybrid Platinum, Luxury, Platinum, Premium | 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L FULL HYBRID EV-FLEX (FHEV), 8 Cyl 6.0 L FULL HYBRID EV-GAS (FHEV), 8 Cyl 6.0 L GAS, 8 Cyl 6.2 L FLEX, 8 Cyl 6.2 L GAS
View related parts
2003 Cadillac Escalade Pinion Bearings
Part Number: 23243839
$71.22 MSRP: $139.44
You Save: $68.22 (49%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bearing, Differential Pinion; Differential Pinion Bearing; Rear Pinion Bearing; Front/Inner/Outer Pinion; Diff/Drive Axle; Pinion/Clutch/Rear Wheel
- Position: Front
- Replaces: 09418357, 26053758, 9418357, 15286375, 20997052, 22786621, 9418356, 09418356, 12479221
- Item Weight: 1.30 Pounds
- Item Dimensions: 4.2 x 4.2 x 2.1 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 23243839
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2003 Cadillac Escalade Submodels:
- Base, Luxury, Platinum, Premium, Premium Luxury, Premium Luxury Platinum, Sport, Sport Platinum, V | 5.3L V8, 6 Cyl 3.0 L DIESEL, 6.0L V8, 8 Cyl 5.3 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 6.0 L GAS, 8 Cyl 6.2 L FLEX, 8 Cyl 6.2 L GAS
View related parts
2003 Cadillac Escalade Pinion Bearings
Part Number: 9413427
$60.64 MSRP: $109.76
You Save: $49.12 (45%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bearing, Differential Drive Pinion Gear Outer; Differential Pinion Bearing; Rear, Front, Outer Pinion Bearings; Differential Drive, Steering Knuckle King, Pinion Shaft, Front Axle Bearings.
- Item Weight: 1.20 Pounds
- Item Dimensions: 3.1 x 3.2 x 3.1 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 9413427
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2003 Cadillac Escalade Submodels:
- Base, Hybrid, Hybrid Platinum, Luxury, Platinum, Premium, Premium Luxury | 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L FULL HYBRID EV-FLEX (FHEV), 8 Cyl 6.0 L FULL HYBRID EV-GAS (FHEV), 8 Cyl 6.0 L GAS, 8 Cyl 6.2 L FLEX, 8 Cyl 6.2 L GAS
View related parts
2003 Cadillac Escalade Pinion Bearings
Part Number: 9413168
$93.86 MSRP: $167.61
You Save: $73.75 (44%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bearing Assembly-Roller; Differential Pinion Bearing; Rear Pinion Bearing; Front Pinion Bearing; Drive Pinion Bearing Assembly.
- Item Weight: 2.30 Pounds
- Item Dimensions: 5.2 x 4.2 x 2.0 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 9413168
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2003 Cadillac Escalade Submodels:
- Base | 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L GAS
View related parts
2003 Cadillac Escalade Pinion Bearings, Outer
Part Number: 15534483
$53.12 MSRP: $94.85
You Save: $41.73 (44%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bearing Assembly, Differential Drive Pinion Gear Outer; Differential Pinion Bearing; Front Pinion Bearing; Bearing, Differential Pinion; Bearing, Pinion Shaft Front
- Position: Outer
- Replaces: 09440836, 9440836
- Item Weight: 1.70 Pounds
- Item Dimensions: 9.0 x 3.6 x 3.5 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 15534483
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2003 Cadillac Escalade Submodels:
- Base | 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L GAS
View related parts
2003 Cadillac Escalade Pinion Bearings
Part Number: 9414917
$70.11 MSRP: $133.08
You Save: $62.97 (48%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bearing, Differential Drive Pinion Gear Inner; Differential Pinion Bearing; Differential Bearing; Rear Pinion Bearing; Drive Pinion Rear; Axle Pinion Shaft; Ring And Pinion; Pinion Shaft Front.
- Position: Inner
- Item Weight: 2.40 Pounds
- Item Dimensions: 4.4 x 5.1 x 2.4 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 9414917
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2003 Cadillac Escalade Submodels:
- Base | 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L GAS
View related parts
2003 Cadillac Escalade Pinion Bearings
Part Number: 9417781
$43.00 MSRP: $103.28
You Save: $60.28 (59%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bearing, Front Differential Drive Pinion Gear Outer; Differential Pinion Bearing; Rear, Front, Outer Pinion Bearing; Differential Drive Pinion Front, Drive Pinion, Pinion Shaft Front, Front Axle
- Position: Front Outer
- Item Weight: 1.40 Pounds
- Item Dimensions: 3.4 x 3.6 x 1.4 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 9417781
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2003 Cadillac Escalade Submodels:
- Base, Luxury, Platinum, Premium | 8 Cyl 5.3 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 6.0 L GAS, 8 Cyl 6.2 L FLEX, 8 Cyl 6.2 L GAS

2003 Cadillac Escalade Pinion Bearing

With a comprehensive array of OEM 2003 Cadillac Escalade Pinion Bearing, from fuel pumps to door handles, our website is a one-stop-shop for your needs. All our genuine 2003 Cadillac Escalade Pinion Bearing are backed by the manufacturer's warranty and are offered at competitive prices in the market. Rest assured, you can shop with complete confidence.

2003 Cadillac Escalade Pinion Bearing Parts Questions & Experts Answers

Q: What tools are required to replace the drive pinion bearings on 8.6 and 9.5 inch axles on 2003 Cadillac Escalade?
A: The tools necessary in order to replace the drive pinion bearings on 8.6 and 9.5 inch axles; oh, and like all vehicles, those that are twenty feet long cost about the same to buy as an ordinary aircraft carrier-http://blogs.obscura.com/lostlabchallenge/home.b on line bakeka.february 2007. J7818 (Inner Bearing Race Installer), j8092 (Universal Driver Handle - 3/4 inch - 10), j8611 (Rear Pinion Bearing Race Installer), j8614-01 (Flange and Pulley Holding Tool), j22306 (Rear Pinion Cup Bearing Installer), j22912-01 (Split Plate Bearing Puller), j24433 (Pinion Cone and Side Bearing Installer), j36614 (Inner Pinion Bearing Installer), j45870 (Pinion Bearing Cup Installer), and j45871 (Pinion Bearing Remover). Start by lifting the vehicle and then removing the right part of theifferential assembly combining with the drive pinion from the axle. For 8.6 inch axle, take 32.151 around Pinion Bearing and the 32.150-1 in reversed position around the 32.151 to apply the pressure and press the bearing off. For the 9.5 inch and 11.5 inch axles, the use of the j22912-01 to press the bearing off. Take off the shim, and both the outer and inner Pinion Bearing cups from the axle housing using a hammer and brass drift. For the installation, the j8611-01 for the outer Pinion Bearing cup should be used on the 8.6 inch axle or one can employ j7818 for the 9.5 inch axle with j8092. For the inner pin ion bearing cup, use the bearing id: j45870 for the 8.6 in axle or the bearing id: j22306 for the 9.5 in axle with the bearing code: j8092. Measure the selective shim thickness and place it between the inner Pinion Bearing and the shoulder on the gear. Install inner Pinion Bearing using the j24433 or j36614 and press it on until cone seats on the pinion shim. Install a new collapsible spacer, lubricate the pinion bearings with axle lubricant, and install the outer Pinion Bearing into the axle housing. Replace yet another new pinion oil seal using the j22388 follow by replacing the pinion into the axle housing. Apply sealant gp, p/n: 12346004 (Canadian P/N: 10953480, or equivalent) to splines of the pinion yoke, and install the pinion yoke, aligning the marks done in removal. Tap in the pinion yoke onto the pinion shaft with a soft-headed hammer until a few threads are visible through the yoke place the washer and the new pinion nut. Tighten with the j8614-01 holding the pinion yoke to take up the pinion end play even though rotating the pinion while tightening to seat bearings. Check the rotating torque of the pinion by using an inch-pound torque wrench and it remains within 1.0 - 2.3 nm (10 - 20 inch lbs.) for used bearings or when used with new bearings-maintain a range of 1.7 - 3.4 nm (15 - 30 inch lbs.). If the torque is below the specification, keep on tightening the pinion nut tightening in small steps until you reach the right torque. After the specified torque is achieved, rotate the pinion a few times to guarantee the seating of the bearings, and check the torque again for any adjustments. Finally, installing the Differential assembly, lubricant the axle, and lowering the vehicle.