How to replace the rear brake calipers on 2007 Chevrolet Express 2500?

Before beginning replacement of the rear brake caliper inspect the brake master cylinder reservoir for its fluid level. Drain fluid from the reservoir if its level exceeds the midway point between maximum and minimum marks. Lift your vehicle safely. Take the tire and wheel system out to work on the brakes. Press the caliper pistons back with a c-clamp placed over the top of the housing while squeezing the clamped end against the back of the outboard pads. Tighten the c-clamp until the pistons fully move towards the rear. Use compressed air to clean the brake hose and protect fluid from leaking out when you install a rubber seal. Untighten and remove the brake hose to caliper bolt while abandoning the two copper brake hose gaskets. First remove the brake caliper guide pin bolts before taking the brake caliper off the vehicle. Inspect the caliper assembly. Install brake pads by putting a c-clamp to hold brake pistons in position at the bottom of the caliper bores while protecting them with old pads, metal plate, or wood. Hold up the inner side of the caliper boot with a small flat tool to let air escape below the piston level. Position the brake caliper on its mounting bracket and apply brake cleaner to threads of guide pin bolts before installing threadlocker gm p/n 12345493 onto the bolts for installation. Secure the guide pin bolts into their positions at 34 n.m (25 lb ft) for the 15 series and 72 n.m (53 lb ft) for the 25/35 series. Insert 2 new copper brake hose gaskets into the brake fitting and then connect the brake hose by tightening its bolt to 40 n.m (30 lb ft). Squeeze the brake to remove air from the lines then attach the tire assembly with wheel. Drop the vehicle below ground level and refill the master brake reservoir through its top opening.

OEM 2007 Chevrolet Express 2500 Brake Calipers

Caliper

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

6 Brake Calipers found

View related parts
2007 Chevrolet Express 2500 Caliper
Part Number: 19331021
$170.23 MSRP: $328.77
You Save: $158.54 (49%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper, Wheel Brake Cylinder/Caliper; Brake Caliper
- Position: Rear
- Replaces: 18040101, 25848000
- Item Weight: 11.90 Pounds
- Item Dimensions: 7.2 x 4.1 x 12.6 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 19331021
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2007 Chevrolet Express 2500 Submodels:
- Base, LS, LT | 6 Cyl 4.3 L GAS, 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L CNG, 8 Cyl 6.0 L GAS, 8 Cyl 6.6 L DIESEL
View related parts
2007 Chevrolet Express 2500 Caliper
Part Number: 19331022
$171.88 MSRP: $331.97
You Save: $160.09 (49%)
ADD TO CART
Product Specifications
- Other Name: Caliper, Wheel Brake Cylinder/Caliper; Brake Caliper
- Position: Rear
- Replaces: 25848001, 18040100
- Item Weight: 11.80 Pounds
- Item Dimensions: 13.0 x 7.1 x 4.1 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 19331022
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2007 Chevrolet Express 2500 Submodels:
- Base, LS, LT | 6 Cyl 4.3 L GAS, 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L CNG, 8 Cyl 6.0 L GAS, 8 Cyl 6.6 L DIESEL
View related parts
2007 Chevrolet Express 2500 Caliper, Front Driver Side
Part Number: 84394384
$107.66 MSRP: $208.96
You Save: $101.30 (49%)
ADD TO CART
Product Specifications
- Other Name: Caliper Assembly-Front Brake (W/O Brake Pads & Bracket; Caliper, Wheel Brake Cylinder/Caliper
- Position: Front Driver Side
- Replaced by: 87859910
- Item Weight: 15.50 Pounds
- Item Dimensions: 8.4 x 5.3 x 14.4 inches
- Condition: New
- SKU: 84394384
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2007 Chevrolet Express 2500 Submodels:
- Base, LS, LT | 4 Cyl 2.8 L DIESEL, 6 Cyl 4.3 L FLEX, 6 Cyl 4.3 L GAS, 8 Cyl 4.8 L FLEX, 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L CNG, 8 Cyl 6.0 L FLEX, 8 Cyl 6.0 L GAS, 8 Cyl 6.6 L DIESEL
View related parts
2007 Chevrolet Express 2500 Caliper, Passenger Side
Part Number: 84803425
$135.01 MSRP: $251.95
You Save: $116.94 (47%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper Assembly-Front Brake (W/O Brake Pads & Bracket); Caliper, Wheel Brake Cylinder/Caliper
- Position: Passenger Side
- Replaced by: 87859911
- Condition: New
- SKU: 84803425
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following 2007 Chevrolet Express 2500 Submodels:
- Base, LS, LT | 4 Cyl 2.8 L DIESEL, 6 Cyl 4.3 L FLEX, 6 Cyl 4.3 L GAS, 8 Cyl 4.8 L FLEX, 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L CNG, 8 Cyl 6.0 L FLEX, 8 Cyl 6.0 L GAS, 8 Cyl 6.6 L DIESEL
View related parts
2007 Chevrolet Express 2500 Caliper, Rear Driver Side
Part Number: 84755503
$97.97 MSRP: $191.81
You Save: $93.84 (49%)
ADD TO CART
Product Specifications
- Other Name: Caliper Assembly-Rear Brake (W/O Brake Pads & Bracket); Brake Caliper; Caliper, Wheel Brake Cylinder/Caliper; Axle, Rear Axle
- Position: Rear Driver Side
- Replaces: 15751175, 84394396, 84046262
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 84755503
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2007 Chevrolet Express 2500 Submodels:
- Base, LS, LT | 4 Cyl 2.8 L DIESEL, 6 Cyl 4.3 L FLEX, 6 Cyl 4.3 L GAS, 8 Cyl 4.8 L FLEX, 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L CNG, 8 Cyl 6.0 L FLEX, 8 Cyl 6.0 L GAS, 8 Cyl 6.6 L DIESEL
View related parts
2007 Chevrolet Express 2500 Caliper, Rear Passenger Side
Part Number: 84046263
$97.97 MSRP: $191.82
You Save: $93.85 (49%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper Assembly-Rear Brake (W/O Brake Pads & Bracket; Brake Caliper
- Position: Rear Passenger Side
- Replaced by: 84755504
- Item Weight: 11.40 Pounds
- Item Dimensions: 8.2 x 5.3 x 12.4 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 84046263
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2007 Chevrolet Express 2500 Submodels:
- Base, LS, LT | 4 Cyl 2.8 L DIESEL, 6 Cyl 4.3 L GAS, 8 Cyl 4.8 L FLEX, 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L CNG, 8 Cyl 6.0 L FLEX, 8 Cyl 6.0 L GAS, 8 Cyl 6.6 L DIESEL

2007 Chevrolet Express 2500 Brake Calipers

With a comprehensive array of OEM 2007 Chevrolet Express 2500 Brake Calipers, from fuel pumps to door handles, our website is a one-stop-shop for your needs. All our genuine 2007 Chevrolet Express 2500 Brake Calipers are backed by the manufacturer's warranty and are offered at competitive prices in the market. Rest assured, you can shop with complete confidence.

2007 Chevrolet Express 2500 Parts Questions & Experts Answers

Q: How to replace the rear brake calipers on 2007 Chevrolet Express 2500?
A: Before beginning replacement of the rear brake caliper inspect the brake master cylinder reservoir for its fluid level. Drain fluid from the reservoir if its level exceeds the midway point between maximum and minimum marks. Lift your vehicle safely. Take the tire and wheel system out to work on the brakes. Press the caliper pistons back with a c-clamp placed over the top of the housing while squeezing the clamped end against the back of the outboard pads. Tighten the c-clamp until the pistons fully move towards the rear. Use compressed air to clean the brake hose and protect fluid from leaking out when you install a rubber seal. Untighten and remove the brake hose to caliper bolt while abandoning the two copper brake hose gaskets. First remove the brake caliper guide pin bolts before taking the brake caliper off the vehicle. Inspect the caliper assembly. Install brake pads by putting a c-clamp to hold brake pistons in position at the bottom of the caliper bores while protecting them with old pads, metal plate, or wood. Hold up the inner side of the caliper boot with a small flat tool to let air escape below the piston level. Position the brake caliper on its mounting bracket and apply brake cleaner to threads of guide pin bolts before installing threadlocker gm p/n 12345493 onto the bolts for installation. Secure the guide pin bolts into their positions at 34 n.m (25 lb ft) for the 15 series and 72 n.m (53 lb ft) for the 25/35 series. Insert 2 new copper brake hose gaskets into the brake fitting and then connect the brake hose by tightening its bolt to 40 n.m (30 lb ft). Squeeze the brake to remove air from the lines then attach the tire assembly with wheel. Drop the vehicle below ground level and refill the master brake reservoir through its top opening.