How to replace the front brake calipers on Chevrolet Express 2500?

When replacing the front brake caliper you need to check the fluid level in the brake master cylinder reservoir first. The fluid needs level adjustment only when it sits between the maximum and minimum marks of the reservoir tank. Start by raising the vehicle then supporting it before taking off the wheel with the tire assembly. Use a large c-clamp to compress the brake caliper pistons while pushing the clamp down against the caliper housing, keeping pressure on until the pistons are fully compressed. Before you replace the brake hose end seal with a rubber plug, you need to remove all dirt and contamination from this area. Separate the brake hose from the caliper by removing the caliper bolt and discarding both copper brake hose gaskets that have attached to either the caliper housing or hose end. To start the procedure remove the 2 brake caliper mounting bolts but be sure to keep the brake pedal from being depressed when the brake components are out because this can cause damage to your system. Extract the brake caliper from its mounting bracket. During assembly mount the new brake caliper onto its bracket then brush the mounting bolt threads with brake parts cleaner before applying threadlocker gm p/n 12345493 (Canadian P/N 10953488) and torquing the 2 bolts at 108 n.m (80 lb ft). First remove the rubber cap from the brake hose fitting and install two new copper brake hose gaskets before securing the brake hose to caliper bolt on the brake caliper at 44 n.m (32 lb ft). After hydraulic brake bleed completion reinstall the tire/wheel assembly then lower the vehicle before adding clean brake fluid to reach proper reservoir level.

How to Service and Repair Rear Brake Calipers (25/35 Series) on Chevrolet Express 2500?

Begin services on the rear brake caliper (25/35 Series) by extracting the component from the vehicle but protecting the pistons with a thin piece of wood while using compressed air to remove the Piston from the brake hose inlet fitting port. First drain the two pistons with their boot equipment and seals before you extract the brake caliper bleed screw and its cap. The brake caliper bores and Piston seal grooves need examination for excessive scoring or corrosion and you must replace the brake caliper housing if necessary. Check the brake caliper mounting bracket for wear because replacement is needed at this point. First dry and cleanse brake pad guiding surfaces and all non-kit parts by applying denatured alcohol followed by blowing with filtered non-lubricated compressed air through all passages in the brake caliper housing and bleeder valve. During assembly of the brake caliper tighten the bleed screw to 12 nm (106 inch lbs.) torque.after tightening the bleed screw to 12 nm torque set point the technician installs the bleed screw cap. Apply brake fluid to the brake caliper bore seal groove after fitting the new Piston seal while making sure the seal stays untwisted before its installation. Apply brake fluid to both the brake caliper bore and Piston before inserting the boot over the Piston. Place the fold section facing the brake caliper housing Piston bore opening. After seating the boot in its groove slide the Piston into the bore. First situate the Piston at the bottom while verifying that the boot sits correctly in both grooves and then continue with the next Piston. Set the brake caliper into its original position on the vehicle.

OEM Chevrolet Express 2500 Brake Calipers

Caliper

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

20 Brake Calipers found

View related parts
Chevrolet Express 2500 Caliper Part Number: 19331021
$170.23 MSRP: $328.77
You Save: $158.54 (49%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper, Wheel Brake Cylinder/Caliper; Brake Caliper
- Position: Rear
- Replaces: 18040101, 25848000
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2003-2008 Chevrolet Express 2500 | Base, LS, LT | 6 Cyl 4.3 L GAS, 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L CNG, 8 Cyl 6.0 L GAS, 8 Cyl 6.6 L DIESEL
View related parts
Chevrolet Express 2500 Caliper Part Number: 19331022
$171.88 MSRP: $331.97
You Save: $160.09 (49%)
ADD TO CART
Product Specifications
- Other Name: Caliper, Wheel Brake Cylinder/Caliper; Brake Caliper
- Position: Rear
- Replaces: 25848001, 18040100
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2003-2008 Chevrolet Express 2500 | Base, LS, LT | 6 Cyl 4.3 L GAS, 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L CNG, 8 Cyl 6.0 L GAS, 8 Cyl 6.6 L DIESEL
View related parts
Chevrolet Express 2500 Caliper, Driver Side Part Number: 85605661
$92.37 MSRP: $164.94
You Save: $72.57 (44%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper Assembly-Rear Brake (W/O Brake Pads & Bracket); Caliper, Wheel Brake Cylinder/Caliper
- Position: Driver Side
- Replaces: 84786067
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2021-2024 Chevrolet Express 2500 | Base, LS, LT | 4 Cyl 2.8 L DIESEL, 6 Cyl 4.3 L FLEX, 6 Cyl 4.3 L GAS, 8 Cyl 6.6 L GAS
View related parts
Chevrolet Express 2500 Caliper, Driver Side Part Number: 87834254
$192.26 MSRP: $376.42
You Save: $184.16 (49%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper Assembly-Front Brake (W/O Brake Pads & Bracket); Caliper, Wheel Brake Cylinder/Caliper
- Position: Driver Side
- Replaces: 84902784
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2021-2024 Chevrolet Express 2500 | Base, LS, LT | 4 Cyl 2.8 L DIESEL, 6 Cyl 4.3 L FLEX, 6 Cyl 4.3 L GAS, 8 Cyl 6.6 L GAS
View related parts
Chevrolet Express 2500 Caliper, Driver Side Part Number: 18040100
$171.88 MSRP: $331.97
You Save: $160.09 (49%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper, Wheel Brake Cylinder/Caliper; Brake Caliper
- Position: Driver Side
- Replaced by: 19331022
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2003-2005 Chevrolet Express 2500 | Base, LS | 6 Cyl 4.3 L GAS, 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L CNG, 8 Cyl 6.0 L GAS
View related parts
Chevrolet Express 2500 Caliper, Rear Driver Side Part Number: 84755503
$99.94 MSRP: $195.65
You Save: $95.71 (49%)
ADD TO CART
Product Specifications
- Other Name: Caliper Assembly-Rear Brake (W/O Brake Pads & Bracket); Brake Caliper; Caliper, Wheel Brake Cylinder/Caliper; Axle, Rear Axle
- Position: Rear Driver Side
- Replaces: 15751175, 84394396, 84046262
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2003-2020 Chevrolet Express 2500 | Base, LS, LT | 4 Cyl 2.8 L DIESEL, 6 Cyl 4.3 L FLEX, 6 Cyl 4.3 L GAS, 8 Cyl 4.8 L FLEX, 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L CNG, 8 Cyl 6.0 L FLEX, 8 Cyl 6.0 L GAS, 8 Cyl 6.6 L DIESEL
View related parts
Chevrolet Express 2500 Caliper, Passenger Side Part Number: 87834253
$192.26 MSRP: $376.42
You Save: $184.16 (49%)
ADD TO CART
Product Specifications
- Other Name: Caliper Assembly-Front Brake (W/O Brake Pads & Bracket); Caliper, Wheel Brake Cylinder/Caliper
- Position: Passenger Side
- Replaces: 84902786
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2021-2024 Chevrolet Express 2500 | Base, LS, LT | 4 Cyl 2.8 L DIESEL, 6 Cyl 4.3 L FLEX, 6 Cyl 4.3 L GAS, 8 Cyl 6.6 L GAS
View related parts
Chevrolet Express 2500 Caliper, Rear Passenger Side Part Number: 84755504
$99.94 MSRP: $195.66
You Save: $95.72 (49%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper Assembly-Rear Brake (W/O Brake Pads & Bracket); Brake Caliper; Caliper, Wheel Brake Cylinder/Caliper
- Position: Rear Passenger Side
- Replaces: 15751176, 84394397, 84046263
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2003-2020 Chevrolet Express 2500 | Base, LS, LT | 4 Cyl 2.8 L DIESEL, 6 Cyl 4.3 L FLEX, 6 Cyl 4.3 L GAS, 8 Cyl 4.8 L FLEX, 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L CNG, 8 Cyl 6.0 L FLEX, 8 Cyl 6.0 L GAS, 8 Cyl 6.6 L DIESEL
View related parts
Chevrolet Express 2500 Caliper, Passenger Side Part Number: 85605662
$94.20 MSRP: $168.22
You Save: $74.02 (44%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper Assembly-Rear Brake (W/O Brake Pads & Bracket); Caliper, Wheel Brake Cylinder/Caliper
- Position: Passenger Side
- Replaces: 84786068
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2021-2024 Chevrolet Express 2500 | Base, LS, LT | 4 Cyl 2.8 L DIESEL, 6 Cyl 4.3 L FLEX, 6 Cyl 4.3 L GAS, 8 Cyl 6.6 L GAS
View related parts
Chevrolet Express 2500 Caliper, Rear Passenger Side Part Number: 84046263
$99.94 MSRP: $195.66
You Save: $95.72 (49%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper Assembly-Rear Brake (W/O Brake Pads & Bracket; Brake Caliper
- Position: Rear Passenger Side
- Replaced by: 84755504
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2003-2017 Chevrolet Express 2500 | Base, LS, LT | 4 Cyl 2.8 L DIESEL, 6 Cyl 4.3 L GAS, 8 Cyl 4.8 L FLEX, 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L CNG, 8 Cyl 6.0 L FLEX, 8 Cyl 6.0 L GAS, 8 Cyl 6.6 L DIESEL
View related parts
Chevrolet Express 2500 Caliper, Passenger Side Part Number: 85569602
$96.77 MSRP: $187.82
You Save: $91.05 (49%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper Assembly-Front Brake (W/O Brake Pads & Bracket); Caliper, Wheel Brake Cylinder/Caliper
- Position: Passenger Side
- Replaces: 15904195, 23290150, 84828461, 89059121, 23276880, 22842351
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2009-2014 Chevrolet Express 2500 | Base, LS, LT | 8 Cyl 4.8 L FLEX, 8 Cyl 4.8 L GAS, 8 Cyl 6.0 L CNG, 8 Cyl 6.0 L FLEX, 8 Cyl 6.0 L GAS, 8 Cyl 6.6 L DIESEL
View related parts
Chevrolet Express 2500 Caliper, Driver Side Part Number: 85569601
$72.50 MSRP: $140.30
You Save: $67.80 (49%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper Assembly-Front Brake (W/O Brake Pads & Bracket); Caliper, Wheel Brake Cylinder/Caliper
- Position: Driver Side
- Replaces: 15904194, 23276878, 22842352, 84828460, 89059117, 23290149
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2009-2014 Chevrolet Express 2500 | Base, LS, LT | 8 Cyl 4.8 L FLEX, 8 Cyl 4.8 L GAS, 8 Cyl 6.0 L CNG, 8 Cyl 6.0 L FLEX, 8 Cyl 6.0 L GAS, 8 Cyl 6.6 L DIESEL
View related parts
Chevrolet Express 2500 Caliper, Passenger Side Part Number: 84803425
$137.69 MSRP: $256.99
You Save: $119.30 (47%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper Assembly-Front Brake (W/O Brake Pads & Bracket); Caliper, Wheel Brake Cylinder/Caliper
- Position: Passenger Side
- Replaced by: 87859911
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2003-2020 Chevrolet Express 2500 | Base, LS, LT | 4 Cyl 2.8 L DIESEL, 6 Cyl 4.3 L FLEX, 6 Cyl 4.3 L GAS, 8 Cyl 4.8 L FLEX, 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L CNG, 8 Cyl 6.0 L FLEX, 8 Cyl 6.0 L GAS, 8 Cyl 6.6 L DIESEL
View related parts
Chevrolet Express 2500 Caliper, Front Driver Side Part Number: 84394384
$109.82 MSRP: $213.14
You Save: $103.32 (49%)
ADD TO CART
Product Specifications
- Other Name: Caliper Assembly-Front Brake (W/O Brake Pads & Bracket; Caliper, Wheel Brake Cylinder/Caliper
- Position: Front Driver Side
- Replaced by: 87859910
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2003-2020 Chevrolet Express 2500 | Base, LS, LT | 4 Cyl 2.8 L DIESEL, 6 Cyl 4.3 L FLEX, 6 Cyl 4.3 L GAS, 8 Cyl 4.8 L FLEX, 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L CNG, 8 Cyl 6.0 L FLEX, 8 Cyl 6.0 L GAS, 8 Cyl 6.6 L DIESEL
View related parts
Chevrolet Express 2500 Caliper Part Number: 15751173
Product Specifications
- Other Name: Housing, Wheel Brake Cylinder/Caliper; Brake Caliper; Caliper, Wheel Brake Cylinder/Caliper
- Position: Rear Driver Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2003-2005 Chevrolet Express 2500 | Base, LS | 6 Cyl 4.3 L GAS, 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L CNG, 8 Cyl 6.0 L GAS
View related parts
Chevrolet Express 2500 Caliper Part Number: 15751174
Product Specifications
- Other Name: Housing, Wheel Brake Cylinder/Caliper; Brake Caliper; Caliper, Wheel Brake Cylinder/Caliper
- Position: Rear Passenger Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2003-2005 Chevrolet Express 2500 | Base, LS | 6 Cyl 4.3 L GAS, 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L CNG, 8 Cyl 6.0 L GAS
View related parts
Chevrolet Express 2500 Caliper, Front Part Number: 18014745
Product Specifications
- Other Name: Caliper, Front Brake; Brake Caliper; Caliper, Wheel Brake Cylinder/Caliper
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1996-2002 Chevrolet Express 2500 | Base, LS | 6 Cyl 4.3 L GAS, 8 Cyl 5.0 L GAS, 8 Cyl 5.7 L BI-FUEL, 8 Cyl 5.7 L CNG, 8 Cyl 5.7 L GAS, 8 Cyl 6.5 L DIESEL
View related parts
Chevrolet Express 2500 Caliper, Front Part Number: 18014744
Product Specifications
- Other Name: Caliper, Front Brake; Brake Caliper; Caliper, Wheel Brake Cylinder/Caliper
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1996-2002 Chevrolet Express 2500 | Base, LS | 6 Cyl 4.3 L GAS, 8 Cyl 5.0 L GAS, 8 Cyl 5.7 L BI-FUEL, 8 Cyl 5.7 L CNG, 8 Cyl 5.7 L GAS, 8 Cyl 6.5 L DIESEL
View related parts
Chevrolet Express 2500 Caliper, Front Driver Side Part Number: 18014747
Product Specifications
- Other Name: Caliper Kit, Front Brake; Brake Caliper; Caliper, Wheel Brake Cylinder/Caliper
- Position: Front Driver Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1996-2002 Chevrolet Express 2500 | Base, LS | 6 Cyl 4.3 L GAS, 8 Cyl 5.0 L GAS, 8 Cyl 5.7 L BI-FUEL, 8 Cyl 5.7 L CNG, 8 Cyl 5.7 L GAS, 8 Cyl 6.5 L DIESEL
View related parts
Chevrolet Express 2500 Caliper, Front Passenger Side Part Number: 18014748
Product Specifications
- Other Name: Caliper Kit, Front Brake; Brake Caliper; Caliper, Wheel Brake Cylinder/Caliper
- Position: Front Passenger Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1996-2002 Chevrolet Express 2500 | Base, LS | 6 Cyl 4.3 L GAS, 8 Cyl 5.0 L GAS, 8 Cyl 5.7 L BI-FUEL, 8 Cyl 5.7 L CNG, 8 Cyl 5.7 L GAS, 8 Cyl 6.5 L DIESEL

Chevrolet Express 2500 Brake Calipers

Want to cut long-term maintenance and repair costs? Choose OEM Brake Calipers. Those parts deliver top durability you can trust. On our site, you'll find a huge catalog of genuine Chevrolet Express 2500 parts. Prices are unbeatable, so you can keep more in your pocket. Every OEM Chevrolet Express 2500 Brake Calipers includes a manufacturer's warranty. You can also get an easy return policy that keeps buying risk free. Fast delivery, get your car on the road quickly. It's simple to search, compare, and order. Stop guessing about quality or fit. Order today and save with parts that last.

Chevrolet Express 2500 Brake Calipers Parts and Q&A

Caliper
19331021
Q: How to replace the front brake calipers on Chevrolet Express 2500?
A:
When replacing the front brake caliper you need to check the fluid level in the brake master cylinder reservoir first. The fluid needs level adjustment only when it sits between the maximum and minimum marks of the reservoir tank. Start by raising the vehicle then supporting it before taking off the wheel with the tire assembly. Use a large c-clamp to compress the brake caliper pistons while pushing the clamp down against the caliper housing, keeping pressure on until the pistons are fully compressed. Before you replace the brake hose end seal with a rubber plug, you need to remove all dirt and contamination from this area. Separate the brake hose from the caliper by removing the caliper bolt and discarding both copper brake hose gaskets that have attached to either the caliper housing or hose end. To start the procedure remove the 2 brake caliper mounting bolts but be sure to keep the brake pedal from being depressed when the brake components are out because this can cause damage to your system. Extract the brake caliper from its mounting bracket. During assembly mount the new brake caliper onto its bracket then brush the mounting bolt threads with brake parts cleaner before applying threadlocker gm p/n 12345493 (Canadian P/N 10953488) and torquing the 2 bolts at 108 n.m (80 lb ft). First remove the rubber cap from the brake hose fitting and install two new copper brake hose gaskets before securing the brake hose to caliper bolt on the brake caliper at 44 n.m (32 lb ft). After hydraulic brake bleed completion reinstall the tire/wheel assembly then lower the vehicle before adding clean brake fluid to reach proper reservoir level.
Caliper, Driver Side
18040100
Q: How to Service and Repair Rear Brake Calipers (25/35 Series) on Chevrolet Express 2500?
A:
Begin services on the rear brake caliper (25/35 Series) by extracting the component from the vehicle but protecting the pistons with a thin piece of wood while using compressed air to remove the Piston from the brake hose inlet fitting port. First drain the two pistons with their boot equipment and seals before you extract the brake caliper bleed screw and its cap. The brake caliper bores and Piston seal grooves need examination for excessive scoring or corrosion and you must replace the brake caliper housing if necessary. Check the brake caliper mounting bracket for wear because replacement is needed at this point. First dry and cleanse brake pad guiding surfaces and all non-kit parts by applying denatured alcohol followed by blowing with filtered non-lubricated compressed air through all passages in the brake caliper housing and bleeder valve. During assembly of the brake caliper tighten the bleed screw to 12 nm (106 inch lbs.) torque.after tightening the bleed screw to 12 nm torque set point the technician installs the bleed screw cap. Apply brake fluid to the brake caliper bore seal groove after fitting the new Piston seal while making sure the seal stays untwisted before its installation. Apply brake fluid to both the brake caliper bore and Piston before inserting the boot over the Piston. Place the fold section facing the brake caliper housing Piston bore opening. After seating the boot in its groove slide the Piston into the bore. First situate the Piston at the bottom while verifying that the boot sits correctly in both grooves and then continue with the next Piston. Set the brake caliper into its original position on the vehicle.