How to replace a two-piece drive shaft on 2009 Chevrolet Silverado 1500?

Vehicle elevation and support constitute the first step for two-piece propeller shaft replacement. A permanent mark on all driveline components from propeller shafts through drive axles and pinion flanges and output shafts will assist future proper reassembly order. First detach both bolts from the rear propeller shaft along with the universal joint strap. A flat-bladed tool must be used to remove the duo-boot clamp which contains the front propeller Slip Yoke and center bearing boot. When removing the yoke ears do not strike them forcefully to prevent damaging the injection joints. Extract the rear propeller shaft from its position both in the center bearing and in the rear axle. You should note and tag the following components when using vehicles equipped with slip yokes: transmission or Transfer Case along with propeller shaft Slip Yoke and universal bearing cap and propeller shaft. Mark each surface on the transmission or Transfer Case and output shaft flange as well as universal joint bearing cap and propeller shaft when the yoke is attached to the output shaft. Unfasten both center bearing support nuts and the center bearing support itself. Before removing propeller shaft bolts and the shaft from the transmission or Transfer Case, use a jack stand to support the propeller shaft when it has the yoke connected to the output shaft. To install this shaft you must first line up reference marks which exist on the transmission or Transfer Case together with the Slip Yoke and universal bearing cap and propeller shaft followed by propeller shaft installation. First tighten all propeller shaft bolts by hand until complete installation of center bearing support bolts and their required torque specifications. After installing the transmission or Transfer Case propeller shaft along with its bolts and straps you must place the center support bearing on the frame. Tighten all center bearing support nuts to 40 nm (30 lb ft). The next step involves securing the front propeller shaft bolts with 25 nm torque before adding new boot clamps with new Slip Yoke to the front shaft. Master splines should receive alignment prior to installing the rear shaft. Clean chassis grease should be applied to both the Slip Yoke and rear propeller shaft before installing the rear piece into the front piece while proper referencing of the marks on the rear axle housing, pinion yoke, universal bearing cap, and rear propeller shaft occurs. Secure the boot and clamps onto the Slip Yoke while torquing the yoke retainer bolts to 25 nm (18 lb ft). To complete the procedure you should utilize the j 43218 and crimp the boot clamps and implement the vehicle lower support removal process.

OEM 2009 Chevrolet Silverado 1500 Drive Shaft

Axle Shaft

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

10 Drive Shafts found

View related parts
2009 Chevrolet Silverado 1500 Drive Shaft
Part Number: 20912697
$1075.64 MSRP: $1442.85
You Save: $367.21 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly-Propeller; Driveshaft; Shaft, Propeller
- Replaces: 15794277
- Item Weight: 17.10 Pounds
- Item Dimensions: 80.4 x 4.3 x 4.3 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 20912697
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2009 Chevrolet Silverado 1500 Submodels:
- Hybrid, LS, LT, LTZ, WT, XFE | 6 Cyl 4.3 L GAS, 8 Cyl 4.8 L FLEX, 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L FULL HYBRID EV-FLEX (FHEV), 8 Cyl 6.0 L FULL HYBRID EV-GAS (FHEV), 8 Cyl 6.0 L GAS, 8 Cyl 6.2 L FLEX
View related parts
2009 Chevrolet Silverado 1500 Drive Shaft
Part Number: 20912702
$1466.37 MSRP: $2050.74
You Save: $584.37 (29%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly-Propeller; Driveshaft; Shaft, Propeller
- Replaces: 15791188, 15940304, 20877203
- Item Weight: 23.40 Pounds
- Item Dimensions: 94.4 x 5.6 x 5.7 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 20912702
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2009 Chevrolet Silverado 1500 Submodels:
- Hybrid, LS, LT, LTZ, WT, XFE | 6 Cyl 4.3 L GAS, 8 Cyl 4.8 L FLEX, 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L FULL HYBRID EV-FLEX (FHEV), 8 Cyl 6.0 L GAS, 8 Cyl 6.2 L FLEX
View related parts
2009 Chevrolet Silverado 1500 Drive Shaft
Part Number: 20912712
Product Specifications
- Other Name: Shaft Assembly-Propeller; Driveshaft; Shaft, Propeller
- Replaces: 25784251
- Item Weight: 21.20 Pounds
- Item Dimensions: 95.2 x 5.8 x 5.6 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 20912712
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2009 Chevrolet Silverado 1500 Submodels:
- LS, LT, LTZ, WT, XFE | 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS
View related parts
2009 Chevrolet Silverado 1500 Drive Shaft Assembly
Part Number: 15711948
Product Specifications
- Other Name: Shaft, Propeller; Driveshaft
- Item Dimensions: 71.5 x 3.8 x 3.6 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 15711948
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following 2009 Chevrolet Silverado 1500 Submodels:
- Hybrid, LS, LT, LTZ, WT, XFE | 6 Cyl 4.3 L GAS, 8 Cyl 4.8 L FLEX, 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L FULL HYBRID EV-FLEX (FHEV), 8 Cyl 6.0 L FULL HYBRID EV-GAS (FHEV), 8 Cyl 6.0 L GAS, 8 Cyl 6.2 L FLEX
View related parts
2009 Chevrolet Silverado 1500 Drive Shaft
Part Number: 20912699
Product Specifications
- Other Name: Shaft Assembly-Propeller; Driveshaft; Shaft, Propeller
- Replaces: 15855534
- Item Weight: 20.40 Pounds
- Item Dimensions: 83.1 x 5.1 x 5.2 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 20912699
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2009 Chevrolet Silverado 1500 Submodels:
- LT, LTZ | 8 Cyl 6.2 L FLEX
View related parts
2009 Chevrolet Silverado 1500 Drive Shaft, Front
Part Number: 22845694
Product Specifications
- Other Name: Shaft Assembly-Front Axle Propeller; Driveshaft; Shaft, Propeller
- Position: Front
- Replaces: 15902927
- Item Weight: 15.70 Pounds
- Item Dimensions: 38.5 x 4.2 x 4.0 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 22845694
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2009 Chevrolet Silverado 1500 Submodels:
- Hybrid, LS, LT, LTZ, WT, XFE | 6 Cyl 4.3 L GAS, 8 Cyl 4.8 L FLEX, 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L FULL HYBRID EV-FLEX (FHEV), 8 Cyl 6.0 L FULL HYBRID EV-GAS (FHEV), 8 Cyl 6.0 L GAS, 8 Cyl 6.2 L FLEX
View related parts
2009 Chevrolet Silverado 1500 Drive Shaft
Part Number: 15286091
Product Specifications
- Other Name: Shaft Assembly-Front & Rear Propeller; Driveshaft; Shaft, Propeller
- Position: Front and Rear
- Item Weight: 42.80 Pounds
- Item Dimensions: 108.7 x 2.7 x 2.8 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 15286091
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2009 Chevrolet Silverado 1500 Submodels:
- LS, LT, LTZ, WT | 6 Cyl 4.3 L GAS, 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L GAS, 8 Cyl 6.2 L FLEX
View related parts
2009 Chevrolet Silverado 1500 Drive Shaft
Part Number: 20912700
Product Specifications
- Other Name: Shaft Assembly-Propeller; Driveshaft; Shaft, Propeller
- Replaces: 15909603
- Item Dimensions: 93.2 x 5.3 x 5.1 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 20912700
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2009 Chevrolet Silverado 1500 Submodels:
- Hybrid | 8 Cyl 6.0 L FULL HYBRID EV-FLEX (FHEV), 8 Cyl 6.0 L FULL HYBRID EV-GAS (FHEV)
View related parts
2009 Chevrolet Silverado 1500 Drive Shaft
Part Number: 20912708
Product Specifications
- Other Name: Shaft Assembly-Propeller; Slip Yoke; Shaft, Propeller
- Replaces: 15791185, 20877205
- Item Dimensions: 83.4 x 5.1 x 5.2 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 20912708
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2009 Chevrolet Silverado 1500 Submodels:
- Hybrid, LS, LT, LTZ, WT, XFE | 6 Cyl 4.3 L GAS, 8 Cyl 4.8 L FLEX, 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L FULL HYBRID EV-FLEX (FHEV), 8 Cyl 6.0 L GAS, 8 Cyl 6.2 L FLEX
View related parts
2009 Chevrolet Silverado 1500 Drive Shaft
Part Number: 20912694
$445.81 MSRP: $704.62
You Save: $258.81 (37%)
Product Specifications
- Other Name: Shaft Assembly-Propeller; Driveshaft; Shaft, Propeller
- Replaces: 15794276, 15791190
- Item Weight: 17.70 Pounds
- Item Dimensions: 80.0 x 5.1 x 5.1 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 20912694
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2009 Chevrolet Silverado 1500 Submodels:
- Hybrid, LS, LT, LTZ, WT, XFE | 6 Cyl 4.3 L GAS, 8 Cyl 4.8 L FLEX, 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L FULL HYBRID EV-FLEX (FHEV), 8 Cyl 6.0 L GAS, 8 Cyl 6.2 L FLEX

2009 Chevrolet Silverado 1500 Drive Shaft

With a comprehensive array of OEM 2009 Chevrolet Silverado 1500 Drive Shaft, from fuel pumps to door handles, our website is a one-stop-shop for your needs. All our genuine 2009 Chevrolet Silverado 1500 Drive Shaft are backed by the manufacturer's warranty and are offered at competitive prices in the market. Rest assured, you can shop with complete confidence.

2009 Chevrolet Silverado 1500 Parts Questions & Experts Answers

Q: How to replace a two-piece drive shaft on 2009 Chevrolet Silverado 1500?
A: Vehicle elevation and support constitute the first step for two-piece propeller shaft replacement. A permanent mark on all driveline components from propeller shafts through drive axles and pinion flanges and output shafts will assist future proper reassembly order. First detach both bolts from the rear propeller shaft along with the universal joint strap. A flat-bladed tool must be used to remove the duo-boot clamp which contains the front propeller Slip Yoke and center bearing boot. When removing the yoke ears do not strike them forcefully to prevent damaging the injection joints. Extract the rear propeller shaft from its position both in the center bearing and in the rear axle. You should note and tag the following components when using vehicles equipped with slip yokes: transmission or Transfer Case along with propeller shaft Slip Yoke and universal bearing cap and propeller shaft. Mark each surface on the transmission or Transfer Case and output shaft flange as well as universal joint bearing cap and propeller shaft when the yoke is attached to the output shaft. Unfasten both center bearing support nuts and the center bearing support itself. Before removing propeller shaft bolts and the shaft from the transmission or Transfer Case, use a jack stand to support the propeller shaft when it has the yoke connected to the output shaft. To install this shaft you must first line up reference marks which exist on the transmission or Transfer Case together with the Slip Yoke and universal bearing cap and propeller shaft followed by propeller shaft installation. First tighten all propeller shaft bolts by hand until complete installation of center bearing support bolts and their required torque specifications. After installing the transmission or Transfer Case propeller shaft along with its bolts and straps you must place the center support bearing on the frame. Tighten all center bearing support nuts to 40 nm (30 lb ft). The next step involves securing the front propeller shaft bolts with 25 nm torque before adding new boot clamps with new Slip Yoke to the front shaft. Master splines should receive alignment prior to installing the rear shaft. Clean chassis grease should be applied to both the Slip Yoke and rear propeller shaft before installing the rear piece into the front piece while proper referencing of the marks on the rear axle housing, pinion yoke, universal bearing cap, and rear propeller shaft occurs. Secure the boot and clamps onto the Slip Yoke while torquing the yoke retainer bolts to 25 nm (18 lb ft). To complete the procedure you should utilize the j 43218 and crimp the boot clamps and implement the vehicle lower support removal process.

Related 2009 Chevrolet Silverado 1500 Parts

Alternate Year Models

2008 Chevrolet Silverado 1500 Drive Shaft 2010 Chevrolet Silverado 1500 Drive Shaft