How to replace the Ignition Control Module on Buick LeSabre?

Start the Ignition Control Module replacement by first switching off ignition power followed by disconnecting the 14-way connector which connects to the Ignition Control Module (ICM). Remove Spark Plug Wires from coil assemblies keeping track of their original positions. The installation process begins with screw removal that attaches coil assemblies to the icm. Afterwards extract coils and the icm from their bracket. Installation requires attaching coils and Ignition Control Module to the bracket while adhering to the fastener notice in service precautions. Tighten all screws holding ignition coils and the icm to the bracket through torque settings of 4.5 n.m (40 lb in). Connect the Spark Plug Wires before connecting the module's 14-way connector by tightening its screw to 2.1 n.m (19 lb in).

How to replace the Ignition Control Module on Buick Century?

The Ignition Control Module is the second component that needs to be replaced. To do so, one has to first disconnect all the electrical connectors at the Ignition Control Module, record the position of the spark plugs for reinstallation purposes and then disconnect them from the ignition coils. After that, unscrew the screws holding the coil assemblies to the Ignition Control Module, and pull off the coils from the module, then take out the module from bracket. For installation, locate the Ignition Control Module back on the bracket and coil installation on to the module must be ensured while adhering to the fastener notice under service precauteness. Tighten the screws up to 4.5 n.m (40 lb in). Lastly, reconnect the Spark Plug Wires as pointed out during removal and plug the electrical connectors to the Ignition Control Module.

How to replace the Ignition Control Module on Buick Regal?

Before replacing the Ignition Control Module turn the ignition off then disconnect the 14-way connector from the resistor block on the Ignition Control Module (ICM). Before wire removal keep track of spark plug wire placements. Start by removing screws that keep the coil assemblies fixed to the icm. Then extract the coils and the icm out from the bracket. Use the bracket to install the coils and Ignition Control Module before tightening the screws retaining both components to the bracket at 4.5 n.m (40 lb in). Follow by connecting the Spark Plug Wires followed by connecting the 14-way connector to the module and using a screw to tighten it to 2.1 n.m (19 lb in).

OEM Buick Ignition Control Module

Ignition Spark Control Module

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

34 Ignition Control Modules found

View related parts
Buick Control Module
Part Number: 10482803
$131.42 MSRP: $270.06
You Save: $138.64 (52%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Module, Electronic Ignition Control (W/O Coil); Ignition Control Module; Ignition Module; ESC Control Module; Coil Module; Module
- Replaced by: 19435467
Fits the following Buick Models:
- Roadmaster | 1996 | Collector's Edition, Estate Wagon Collector's Edition, Limited Collector's Edition | 8 Cyl 5.7 L GAS
View related parts
Buick Ignition Module
Part Number: 19260720
$159.90 MSRP: $498.88
You Save: $338.98 (68%)
ADD TO CART
Product Specifications
- Other Name: Module Assembly, Electronic Ignition Control (W/O Coil); Ignition Control Module; Module; Module, Distributor (Also Knock Sensor)
- Replaces: 24503624
Fits the following Buick Models:
- Century | 1984-1993 | Custom, Estate Wagon, Limited, Special, T-Type | 4 Cyl 2.2 L GAS, 4 Cyl 2.5 L GAS, 6 Cyl 2.8 L GAS, 6 Cyl 3.0 L GAS, 6 Cyl 3.3 L GAS, 6 Cyl 3.8 L GAS, 6 Cyl 4.3 L DIESEL
- Electra | 1987 | Limited, Park Avenue, T-Type | 6 Cyl 3.8 L GAS
- LeSabre | 1986-1988 | Base, Custom, Limited, T-Type | 6 Cyl 3.0 L GAS, 6 Cyl 3.8 L GAS
- Riviera | 1986-1987 | Luxury, T-Type | 6 Cyl 3.8 L GAS
View More
View related parts
Buick Ignition Module
Part Number: 10469470
$264.99 MSRP: $544.54
You Save: $279.55 (52%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Ignition Control Module
- Replaced by: 19435469
Fits the following Buick Models:
- Regal | 1990-1991 | Custom, Gran Sport, Limited | 6 Cyl 3.8 L GAS
View related parts
Buick Ignition Module
Part Number: 24503623
$172.64 MSRP: $538.61
You Save: $365.97 (68%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Module Assembly, Electronic Ignition Control (W/O Coil); Ignition Control Module; Coil Module; Module; Module, Distributor (Also Knock Sensor)
Fits the following Buick Models:
- Electra | 1988-1990 | Limited, Park Avenue, Park Avenue Ultra, T-Type | 6 Cyl 3.8 L GAS
- LeSabre | 1989-1992 | Base, Custom, Limited | 6 Cyl 3.8 L GAS
- Park Avenue | 1991-1992 | Base, Ultra | 6 Cyl 3.8 L GAS
- Reatta | 1988-1990 | Base | 6 Cyl 3.8 L GAS
- Riviera | 1988-1990 | Luxury, T-Type | 6 Cyl 3.8 L GAS
View More
View related parts
Buick Ignition Module
Part Number: 16126761
Product Specifications
- Other Name: Module, Windshield Defroster; Ignition Control Module; ESC Module; ESC Control Module; Module; Module, Distributor (Also Knock Sensor)
Fits the following Buick Models:
- Roadmaster | 1991 | Estate Wagon | 8 Cyl 5.0 L GAS
View related parts
Buick Spark Module
Part Number: 16128261
Product Specifications
- Other Name: Module, Windshield Defroster; Ignition Control Module; ESC Control Module; Module; Module, Distributor (Also Knock Sensor)
- Replaces: 16052401
Fits the following Buick Models:
- Roadmaster | 1992-1993 | Base, Estate Wagon, Limited | 8 Cyl 5.7 L GAS
View related parts
Buick Control Module
Part Number: 16214671
Product Specifications
- Other Name: Module, Distributor (Also Knock Sensor); Ignition Control Module; ESC Module; ESC Control Module
Fits the following Buick Models:
- Roadmaster | 1996 | Collector's Edition, Estate Wagon Collector's Edition, Limited Collector's Edition | 8 Cyl 5.7 L GAS
View related parts
Buick ESC Module
Part Number: 16218993
Product Specifications
- Other Name: Module, Distributor (Also Knock Sensor); Ignition Control Module; ESC Control Module
Fits the following Buick Models:
- Century | 1996 | Limited, Special | 4 Cyl 2.2 L GAS
View related parts
Buick Ignition Module
Part Number: 16022654
Product Specifications
- Other Name: Module, Distributor (Also Knock Sensor); Ignition Control Module; Distributor Rotor; ESC Control Module; Rotor
Fits the following Buick Models:
- Regal | 1984-1986 | Base, Limited | 6 Cyl 3.8 L GAS
View related parts
Buick Control Module
Part Number: 16188309
Product Specifications
- Other Name: Module, Distributor (Also Knock Sensor); Ignition Control Module; ESC Control Module
Fits the following Buick Models:
- Roadmaster | 1994-1995 | Base, Estate Wagon, Limited | 8 Cyl 5.7 L GAS
View related parts
Buick Ignition Module
Part Number: 16064134
Product Specifications
- Other Name: Module, Distributor (Also Knock Sensor); Ignition Control Module; Spark Module
Fits the following Buick Models:
- LeSabre | 1987-1988 | Base, Custom, Limited, T-Type | 6 Cyl 3.8 L GAS
View related parts
Buick Knock Sensor
Part Number: 16216564
Product Specifications
- Other Name: Module, Distributor (Also Knock Sensor); Ignition Control Module; ESC Module; Spark Module; ESC Control Module
Fits the following Buick Models:
- Century | 1996-1997 | Custom, Limited, Special | 6 Cyl 3.1 L GAS
- Regal | 1996 | Custom | 6 Cyl 3.1 L GAS
View related parts
Buick Control Module
Part Number: 19178830
Product Specifications
- Other Name: Module Assembly, Electronic Ignition Control (W/O Coil); Ignition Control Module; Ignition Module; Coil Module; Module; Module, Distributor (Also Knock Sensor)
- Replaces: 10469867
Fits the following Buick Models:
- Skylark | 1988-1992 | Base, Custom, Gran Sport, Limited, Luxury Edition | 4 Cyl 2.3 L GAS
View related parts
Buick Ignition Module
Part Number: 16022614
Product Specifications
- Other Name: Module, Distributor (Also Knock Sensor); Ignition Control Module
Fits the following Buick Models:
- Regal | 1984-1986 | Base, Limited | 6 Cyl 3.8 L GAS
View related parts
Buick Ignition Module
Part Number: 16022604
Product Specifications
- Other Name: Module, Distributor (Also Knock Sensor); Ignition Control Module; Spark Module
Fits the following Buick Models:
- Century | 1984-1985 | Custom, Estate, Estate Wagon, Limited, Olympia Limited, T-Type | 6 Cyl 3.0 L GAS
View related parts
Buick Ignition Module
Part Number: 19179582
Product Specifications
- Other Name: Module Assembly, Distributor Ignition Control; Ignition Control Module; Module; Module, Distributor (Also Knock Sensor)
- Replaces: 10492782, 10482835, 16140079
Fits the following Buick Models:
- Skyhawk | 1984 | Custom, Limited | 4 Cyl 2.0 L GAS
View related parts
Buick Ignition Module
Part Number: 16049534
Product Specifications
- Other Name: Module, Distributor (Also Knock Sensor); Ignition Control Module; Spark Module
Fits the following Buick Models:
- Electra | 1986 | Limited, Park Avenue, T-Type | 6 Cyl 3.8 L GAS
- LeSabre | 1986 | Custom, Limited | 6 Cyl 3.0 L GAS, 6 Cyl 3.8 L GAS
View related parts
Buick Ignition Module
Part Number: 19178829
Product Specifications
- Other Name: Module Assembly, Electronic Ignition Control (W/O Coil); Ignition Control Module; Module; Module, Distributor (Also Knock Sensor)
- Replaces: 10467214
Fits the following Buick Models:
- Skyhawk | 1987-1989 | Custom, Limited, SE, Sport, T-Type | 4 Cyl 2.0 L GAS
View related parts
Buick Ignition Module
Part Number: 19178831
Product Specifications
- Other Name: Module Assembly, Electronic Ignition Control (W/O Coil); Ignition Control Module; Module; Module, Distributor (Also Knock Sensor)
- Replaces: 10474855, 10476634
Fits the following Buick Models:
- Century | 1994-1996 | Custom, Limited, Special | 4 Cyl 2.2 L GAS, 6 Cyl 3.1 L GAS
View related parts
Buick Ignition Coil
Part Number: 25518358
Product Specifications
- Other Name: Module, Distributor (Also Knock Sensor)
Fits the following Buick Models:
- Regal | 1984-1985 | Base, Grand National, Limited, T-Type | 6 Cyl 3.8 L GAS, 6 Cyl 4.1 L GAS

| Page 1 of 2 |Next >

1-20 of 34 Results

Buick Ignition Control Module Parts Questions & Experts Answers

Ignition Module
19245558
Q: How to replace the Ignition Control Module on Buick LeSabre?
A: Start the Ignition Control Module replacement by first switching off ignition power followed by disconnecting the 14-way connector which connects to the Ignition Control Module (ICM). Remove Spark Plug Wires from coil assemblies keeping track of their original positions. The installation process begins with screw removal that attaches coil assemblies to the icm. Afterwards extract coils and the icm from their bracket. Installation requires attaching coils and Ignition Control Module to the bracket while adhering to the fastener notice in service precautions. Tighten all screws holding ignition coils and the icm to the bracket through torque settings of 4.5 n.m (40 lb in). Connect the Spark Plug Wires before connecting the module's 14-way connector by tightening its screw to 2.1 n.m (19 lb in).
Control Module
19245557
Q: How to replace the Ignition Control Module on Buick Century?
A: The Ignition Control Module is the second component that needs to be replaced. To do so, one has to first disconnect all the electrical connectors at the Ignition Control Module, record the position of the spark plugs for reinstallation purposes and then disconnect them from the ignition coils. After that, unscrew the screws holding the coil assemblies to the Ignition Control Module, and pull off the coils from the module, then take out the module from bracket. For installation, locate the Ignition Control Module back on the bracket and coil installation on to the module must be ensured while adhering to the fastener notice under service precauteness. Tighten the screws up to 4.5 n.m (40 lb in). Lastly, reconnect the Spark Plug Wires as pointed out during removal and plug the electrical connectors to the Ignition Control Module.
Ignition Module
19245558
Q: How to replace the Ignition Control Module on Buick Regal?
A: Before replacing the Ignition Control Module turn the ignition off then disconnect the 14-way connector from the resistor block on the Ignition Control Module (ICM). Before wire removal keep track of spark plug wire placements. Start by removing screws that keep the coil assemblies fixed to the icm. Then extract the coils and the icm out from the bracket. Use the bracket to install the coils and Ignition Control Module before tightening the screws retaining both components to the bracket at 4.5 n.m (40 lb in). Follow by connecting the Spark Plug Wires followed by connecting the 14-way connector to the module and using a screw to tighten it to 2.1 n.m (19 lb in).

Related Buick Parts

Browse Buick Ignition Control Module by Models

Reatta Regal Riviera Skylark LaCrosse LeSabre Century Lucerne Roadmaster Electra Park Avenue Rainier Rendezvous Skyhawk Somerset