How to replace the front disc brake pads on Buick LaCrosse?

Check the brake master cylinder reservoir fluid before pad replacement. You need not refill if the fluid level matches the minimum-mark position but you must add or remove fluid to reach this level when the fluid level is higher. Lift and stabilize the vehicle before taking off both tire and wheel pieces. Wrap a big c-clamp across the brake caliper body onto the outer Brake Pad and push the Brake Caliper Piston all the way to the brake caliper housing using the c-clamp. Use hand tools alone to remove guide pin bolts but hold the caliper guide pin with an open-end wrench to keep it away from contact with the brake caliper during installation. Install mechanic wire within the brake caliper assembly to keep the hydraulic brake hose from harm while it stands separated. Pick up the brake caliper while noting the wear sensor position and take out the inner and outer brake pads plus upper and lower pad springs. For new brake pads you should replace all springs and put the inner Brake Pad first followed by the outer Brake Pad before putting back the brake caliper into position. Secure the brake caliper using a back up wrench while installing the lower brake caliper guide pin bolt and tightening to 27 nm torque value (20 lb ft). Put on the tire and wheel device. While keeping the engine off apply the brake pedal to its third using slow increments before releasing. Repeat until you achieve a solid brake reaction. Add reservoir fluid before using a Brake Pad burnisher on the metal components.

How to Replace Rear Disc Brake Pads (JL9) for Optimal Brake Pad Performance on Buick LaCrosse?

Before replacing the rear disc brake pads (JL9) you should check the brake master cylinder reservoir fluid level. Lower the fluid amount when the current level is beyond the midpoint between maximum and minimum limits. Place the vehicle on stands while you remove both the rear tire and wheel unit. Secure the brake rotor in place using a single tight handlug nut while holding the caliper piston compressed with a c-clamp . Pull off the upper caliper bolt while guarding the pin boot and suspend the brake caliper with mechanic wire to protect the flexible brake hose. Droop the caliper to reach underneath without taking it off and take both brake pads and their 2 retention clips from the stroker bracket. Test the caliper mounting hardware and dust boot for damage then replace anything that is not usable. Test the caliper bolts for rust damage then include new replacement parts in your plan. Begin the process by pushing the caliper piston down with a c-clamp and protective pad layer. Put the 2 retainers onto the caliper bracket following the proper wear sensor placement on the outside pad. Insert the pads through the caliper bracket then raise the caliper over them and add silicone grease to the bolt and bolt boot. Install the upper caliper bolt at 44 n.m (32 lb ft) torque setting. Lower down the vehicle after placing the wheel and tire back on while keeping the rotor marks lined up. When the engine is not running press the brake pedal to 2/3 of its range and relax it slowly. Press the brake pedal two times during each 15-second period to set the brake caliper pads and pistons in their correct position. Complete the system by topping up the brake fluid to its needed mark while gently working the brakes to break in the pads and rotors.

OEM Buick LaCrosse Brake Pad

Disc Brake Pad Set

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

13 Brake Pads found

View related parts
Buick LaCrosse Brake Pads Part Number: 84259368
$74.70 MSRP: $142.14
You Save: $67.44 (48%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Pad Kit, Brake; Disc Brake Hardware Kit; Rear Pads; Front Pads
- Position: Front
- Replaces: 23303281
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2017-2019 Buick LaCrosse | Avenir, Base, Essence, Preferred, Premium, Sport Touring | 4 Cyl 2.5 L MILD HYBRID EV-GAS (MHEV), 6 Cyl 3.6 L GAS
View related parts
Buick LaCrosse Brake Pads Part Number: 84233325
$81.23 MSRP: $159.04
You Save: $77.81 (49%)
ADD TO CART
Product Specifications
- Other Name: Pad Kit, Brake; Disc Brake Hardware Kit; Front Pads
- Position: Front
- Replaces: 23316342, 20963796
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2011-2016 Buick LaCrosse | Base, Convenience, CX, CXL, CXS, Leather, Premium, Sport Touring, Touring | 4 Cyl 2.4 L GAS, 4 Cyl 2.4 L MILD HYBRID EV-GAS (MHEV), 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS
View related parts
Buick LaCrosse Brake Pads Part Number: 18048690
$85.41 MSRP: $154.58
You Save: $69.17 (45%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Pad Kit, Brake; Disc Brake Hardware Kit; Rear Pads
- Position: Rear
- Replaces: 19209499
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2005-2009 Buick LaCrosse | CX, CXL, CXS | 6 Cyl 3.6 L GAS, 6 Cyl 3.8 L GAS
View related parts
Buick LaCrosse Front Pads Part Number: 22959104
$81.03 MSRP: $222.75
You Save: $141.72 (64%)
ADD TO CART
Product Specifications
- Other Name: Pad Kit, Brake; Disc Brake Hardware Kit; Brake Pads
- Position: Front
- Replaces: 13237751
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2016 Buick LaCrosse | Base, Leather, Premium, Sport Touring | 4 Cyl 2.4 L MILD HYBRID EV-GAS (MHEV), 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS
View related parts
Buick LaCrosse Brake Pads Part Number: 85143529
$84.19 MSRP: $163.41
You Save: $79.22 (49%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Pad Kit, Brake; Rear Pads
- Position: Rear
- Replaces: 13237768, 84144898, 20978663, 22846361
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2010-2016 Buick LaCrosse | Base, Convenience, CX, CXL, CXS, Leather, Premium, Sport Touring, Touring | 4 Cyl 2.4 L GAS, 4 Cyl 2.4 L MILD HYBRID EV-GAS (MHEV), 6 Cyl 3.0 L GAS, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS
View related parts
Buick LaCrosse Brake Pads Part Number: 85143526
$84.19 MSRP: $163.41
You Save: $79.22 (49%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Pad Kit, Brake; Rear Pads
- Position: Rear
- Replaces: 20965713, 22846359
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2011-2016 Buick LaCrosse | Base, Convenience, CX, CXL, CXS, Leather, Premium, Sport Touring, Touring | 4 Cyl 2.4 L GAS, 4 Cyl 2.4 L MILD HYBRID EV-GAS (MHEV), 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS
View related parts
Buick LaCrosse Brake Pads Part Number: 85127904
$166.78 MSRP: $323.69
You Save: $156.91 (49%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Pad Kit, Brake; Rear Pads
- Position: Front
- Replaces: 13527902, 13595651
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2017-2019 Buick LaCrosse | Avenir, Base, Essence, Preferred, Premium, Sport Touring | 4 Cyl 2.5 L MILD HYBRID EV-GAS (MHEV), 6 Cyl 3.6 L GAS
View related parts
Buick LaCrosse Brake Pads Part Number: 85127895
$99.63 MSRP: $195.06
You Save: $95.43 (49%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Pad Kit, Brake; Disc Brake Hardware Kit; Rear Pads; Front Pads
- Position: Front
- Replaces: 84206102, 23326280
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2017-2019 Buick LaCrosse | Avenir, Base, Essence, Preferred, Premium, Sport Touring | 4 Cyl 2.5 L MILD HYBRID EV-GAS (MHEV), 6 Cyl 3.6 L GAS
View related parts
Buick LaCrosse Brake Pads Part Number: 13312895
$160.21 MSRP: $313.65
You Save: $153.44 (49%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Pad Kit, Brake; Disc Brake Hardware Kit; Front Pads
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2012-2016 Buick LaCrosse | Base, Convenience, Leather, Premium, Sport Touring, Touring | 4 Cyl 2.4 L MILD HYBRID EV-GAS (MHEV), 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS
View related parts
Buick LaCrosse Brake Pads Part Number: 13237753
$141.04 MSRP: $255.28
You Save: $114.24 (45%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Pad Kit, Brake; Disc Brake Hardware Kit; Front Pads
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2010 Buick LaCrosse | CX, CXL, CXS | 4 Cyl 2.4 L GAS, 6 Cyl 3.0 L GAS, 6 Cyl 3.6 L GAS
View related parts
Buick LaCrosse Brake Pads Part Number: 20932123
Product Specifications
- Other Name: Pad Kit, Brake; Disc Brake Hardware Kit; Front Pads
- Position: Front
- Replaces: 25996832, 15812610
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2008-2009 Buick LaCrosse | Super | 8 Cyl 5.3 L GAS
View related parts
Buick LaCrosse Brake Pads Part Number: 19209340
$75.43 MSRP: $134.70
You Save: $59.27 (44%)
Product Specifications
- Other Name: Pad Kit, Brake; Disc Brake Hardware Kit; Rear Pads
- Position: Rear
- Replaces: 88967229, 18045984
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2008-2009 Buick LaCrosse | Super | 8 Cyl 5.3 L GAS
View related parts
Buick LaCrosse Brake Pads, Front Part Number: 19121389
Product Specifications
- Other Name: Pad Kit, Front Disc Brake; Disc Brake Hardware Kit; Front Pads; Pad Kit, Brake
- Position: Front
- Replaces: 88964099
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2005-2009 Buick LaCrosse | CX, CXL, CXS | 6 Cyl 3.6 L GAS, 6 Cyl 3.8 L GAS

Buick LaCrosse Brake Pad

Want to cut long-term maintenance and repair costs? Choose OEM Brake Pad. Those parts deliver top durability you can trust. On our site, you'll find a huge catalog of genuine Buick LaCrosse parts. Prices are unbeatable, so you can keep more in your pocket. Every OEM Buick LaCrosse Brake Pad includes a manufacturer's warranty. You can also get an easy return policy that keeps buying risk free. Fast delivery, get your car on the road quickly. It's simple to search, compare, and order. Stop guessing about quality or fit. Order today and save with parts that last.

The Buick LaCrosse Brake Pad is one of the brake parts which ensures safety and reliable braking for all types of LaCrosse models. standing as the contact surface on the rotors, these brake pads are specially intended to rub against the rotors to wear down kinetic energy and convert it into thermal energy to ensure that a car is slowed down safely and effectively. The material used in constructing the Buick LaCrosse Brake Pad shall be of a high quality that could withstand high temperatures preventing scenarios like the brake fade or excessive rotor wear. Thus, we can assert that the specified components are vital for the effective brake system, which is critical for vehicle safety and efficient operation due to the importance of timely brake pads' maintenance and their replacement. The Buick LaCrosse that was first launched in 2004 has gone a long way to show devotion to style and reliability and considering that brake pads are a pretty fundamental feature in any car, it becomes evident that LaCrosse issue brake pads for those drivers with a desire for superior performance. Ability to adapt to LaCrosse models means that drivers are able to get the premier out of the car in terms of safety and efficiency regardless to the model they own. Also, these Buick LaCrosse Brake Pad differs from many other automotive spare parts at the market by the following factors, an enhanced design; features the brake pad with components that enhances its quiet operation and low dusting tendency. Such care does not only improve the driving experience but also increases the life span of the breaking system. Therefore, the Buick LaCrosse Brake Pad is a suitable representation of Buick's commitment to the three aspects of quality, safety, and performance; hence is a must-have part for the LaCrosse car.

Buick LaCrosse Brake Pad Parts and Q&A

Brake Pads
13237753
Q: How to replace the front disc brake pads on Buick LaCrosse?
A:
Check the brake master cylinder reservoir fluid before pad replacement. You need not refill if the fluid level matches the minimum-mark position but you must add or remove fluid to reach this level when the fluid level is higher. Lift and stabilize the vehicle before taking off both tire and wheel pieces. Wrap a big c-clamp across the brake caliper body onto the outer Brake Pad and push the Brake Caliper Piston all the way to the brake caliper housing using the c-clamp. Use hand tools alone to remove guide pin bolts but hold the caliper guide pin with an open-end wrench to keep it away from contact with the brake caliper during installation. Install mechanic wire within the brake caliper assembly to keep the hydraulic brake hose from harm while it stands separated. Pick up the brake caliper while noting the wear sensor position and take out the inner and outer brake pads plus upper and lower pad springs. For new brake pads you should replace all springs and put the inner Brake Pad first followed by the outer Brake Pad before putting back the brake caliper into position. Secure the brake caliper using a back up wrench while installing the lower brake caliper guide pin bolt and tightening to 27 nm torque value (20 lb ft). Put on the tire and wheel device. While keeping the engine off apply the brake pedal to its third using slow increments before releasing. Repeat until you achieve a solid brake reaction. Add reservoir fluid before using a Brake Pad burnisher on the metal components.
Brake Pads
19209340
Q: How to Replace Rear Disc Brake Pads (JL9) for Optimal Brake Pad Performance on Buick LaCrosse?
A:
Before replacing the rear disc brake pads (JL9) you should check the brake master cylinder reservoir fluid level. Lower the fluid amount when the current level is beyond the midpoint between maximum and minimum limits. Place the vehicle on stands while you remove both the rear tire and wheel unit. Secure the brake rotor in place using a single tight handlug nut while holding the caliper piston compressed with a c-clamp . Pull off the upper caliper bolt while guarding the pin boot and suspend the brake caliper with mechanic wire to protect the flexible brake hose. Droop the caliper to reach underneath without taking it off and take both brake pads and their 2 retention clips from the stroker bracket. Test the caliper mounting hardware and dust boot for damage then replace anything that is not usable. Test the caliper bolts for rust damage then include new replacement parts in your plan. Begin the process by pushing the caliper piston down with a c-clamp and protective pad layer. Put the 2 retainers onto the caliper bracket following the proper wear sensor placement on the outside pad. Insert the pads through the caliper bracket then raise the caliper over them and add silicone grease to the bolt and bolt boot. Install the upper caliper bolt at 44 n.m (32 lb ft) torque setting. Lower down the vehicle after placing the wheel and tire back on while keeping the rotor marks lined up. When the engine is not running press the brake pedal to 2/3 of its range and relax it slowly. Press the brake pedal two times during each 15-second period to set the brake caliper pads and pistons in their correct position. Complete the system by topping up the brake fluid to its needed mark while gently working the brakes to break in the pads and rotors.