OEM Buick Park Avenue Air Bag Clockspring

Buick Park Avenue Air Bag Clockspring Parts and Q&A

• Clockspring
  26087277
  Q: How to Remove and Install the Air Bag Clockspring Assembly on Buick Park Avenue?

  A:

  Begin air bag clock spring assembly / spiral cable removal by disabling the sir system first. After removing the inflatable restraint Steering Wheel module and the Steering Wheel nut you need to note the alignment mark between the Steering Shaft and the Steering Wheel. First remove the Steering Wheel from the shaft then pull the tilt lever straight outward while grasping it to extract the tilt lever assembly. Beginning installation demands removal of two pan head tapping screws from the lower shroud followed by the lower shroud itself. Begin the upper shroud removal process by pulling out one torx(R) head screw followed by removal of the upper shroud itself. Release the wire harness straps from the Steering Wheel column harness then remove the retaining ring to extract the inflatable restraint Steering Wheel module coil from the Steering Shaft. First align the block tooth and centering mark at the 12 o'clock position of the race and upper shaft assembly when installing the wheels into a straight ahead position. The coil assembly notice provides centering instructions which must be followed. All new sir coil assemblies arrive with centering accomplished by factory settings. Check if the coil assembly remains in a proper center position. Slid the sir coil assembly into place with the horn tower facing the turn signal cancel cam assembly before installing the wave washer onto the upper shaft assembly. Place the coil assembly onto the race and upper shaft assembly. Next insert the retaining ring followed by the disposal of the centering tab. Use a torx(R) head screw to attach one item to the upper shroud before tightening it to 1.5 n.m (13 lb in). Secure two pan head tapping screws to fasten the lower shroud by torquing each to 3.5 n.m (31 lb in). Pull the tilt lever into the steering column slot before pushing its handle to secure it into place. Thread wiring from the wheel center through before aligning the wheel with the Steering Shaft's reference mark. Install the wheel fastener with 41 n.m (30 lb ft) torque. Run wires to the sir module while you install the inflatable restraint Steering Wheel component before activating the sir functionality.
• Clockspring
  26087287
  Q: How to replace the Air Bag Clockspring in the steering wheel module on Buick Park Avenue?

  A:

  To replace the coil for the inflatable restraint Steering Wheel module, first, disable the sir system. Remove the inflatable restraint Steering Wheel module, steering wheel nut, and record the alignment mark on the Steering Shaft Steering Wheel. Remove the Steering Wheel, grip and pull out the tilt lever, and then alleviated the tilt lever assembly. Next, remove the 2 pan head tapping screws from the lower shroud and also remove the lower shroud. After replacing its bore, fit the upper shroud back in place and secure it with one torx® head screw that you took off. Remove the wire harness straps from the Steering Wheel column wire harness, then take out the retaining ring as well as the air bag clock spring from the Steering Shaft. For installation, align the block tooth and centering mark at 12 o'clock. A new sir coil assembly will arrive pre-centered, so check for centering. Align sir coil assembly to horn tower on the turn signal cancel cam assembly, slip wave washer to upper shaft assembly, and slide the coil assembly onto the race and upper shaft assembly. Push the centering tab to a side & discard it, and install the retaining ring. Mount the upper shroud and tighten it with a 1.5 nm (13 lb in) torque torx® head screw. Mount the lower shroud in place and fix it using 2 pan head tapping screws tightened to 3.5 n.m (31 lb in). Spindle the tilt lever in to the Steering Column and push the tilt lever handle till it tightens. Feed the wiring into the Steering Wheel, line up the Steering Wheel with the mark on the Steering Shaft and install the Steering Wheel nut, tighten up to 41 n.m (30 lb ft). Connect the sir module, the inflatable restraint Steering Wheel module and the last step is to enable the sir system.