How to replace the ABS Control Module on Buick Regal?

You should start the ABS Control Module (ABSCM) replacement process by setting the ignition switch to off because this stops equipment damage from occurring. The first step requires eliminating the fuel injector sight shield from 3.8 l engines followed by removal of the front fender upper diagonal brace. Accomplish disconnecting first the Cruise Control Module from the left strut tower along with the accelerator control cable from its bracket without cutting the cable. Set aside the module and cables in their current locations. The procedure starts with removing the air cleaner intake duct followed by loosening the red locking tab from the connector lock tab. Subsequently detach the abscm harness connector by moving the sliding connector cover to the open position. Clean the component assembly and separate the four abscm to bpmv retainers while taking precautions against toolkit damage to the bpmv surface or solenoid valves. The abscm separation from bpmv should be conducted without excessive force. Attach the abscm to the bpmv while installing four retainers that require tightening to 5 nm (44 inch lbs.). Next step is to connect the abscm harness connector while pushing down the lock tab until you reach the locked position which reengages the red locking tab. After that, reinstall the air cleaner intake duct along with the module and cables and connect the Cruise Control Module at the left strut tower. Reposition the accelerator and cruise control cable to its bracket on the accelerator control cable bracket while also installing the front fender upper diagonal brace and fuel injector sight shield which applies to 3.8l engine models only. End the procedure by using the ignition key to access the run position without starting the engine and initiating the diagnostic system check - abs.

How to Safely Remove and Install the ABS Control Module on Buick Regal?

The removal process for ABS Control Module (ABSCM) begins with setting the Ignition Switch to off to protect equipment components. First unlock the connector lock tab with your finger by pulling out its red locking tab. After that, push down on lock tab followed by sliding connector cover into an open position to disconnect the abscm harness connector. The assembly cleaning process requires dirt removal before the four abscm to bpmv screws are removed to separate the abscm from the bpmv while maintaining a tool-free separation of the abscm from the bpmv surface and solenoid valves. First clean the bpmv surface with alcohol using a cleaned rag and then mount the abscm to bpmv while tightening its installing screws to 5 nm (44 inch lbs.). Reconnecting the abscm harness connector should be followed by pressing the lock tab while sliding the connector cover until it reaches its locked position before completing with the red locking tab. Conclude by activating the Ignition Switch to run without engine start to execute the a diagnostic system check-abs.

OEM Buick Regal ABS Control Module

Anti Lock Brake Control Module

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

34 ABS Control Modules found

View related parts
Buick Regal Control Module Part Number: 23227589
$430.87 MSRP: $779.85
You Save: $348.98 (45%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Module Assembly-Electronic Brake Control (W/Brake Pressure Mode; ABS Control Module; Modulator Valve; ABS Control Unit
- Replaced by: 85148431
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2014-2015 Buick Regal | Base, GS, Premium | 4 Cyl 2.0 L GAS, 4 Cyl 2.4 L FLEX, 4 Cyl 2.4 L MILD HYBRID EV-GAS (MHEV)
View related parts
Buick Regal Control Module Part Number: 84107109
$261.95 MSRP: $530.18
You Save: $268.23 (51%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Module, Electronic Brake Control; Modulator Valve
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2014-2017 Buick Regal | Base, GS, Premium, Sport Touring | 4 Cyl 2.0 L GAS, 4 Cyl 2.4 L FLEX, 4 Cyl 2.4 L GAS, 4 Cyl 2.4 L MILD HYBRID EV-GAS (MHEV)
View related parts
Buick Regal Control Module Part Number: 18078132
Product Specifications
- Other Name: Module Assembly, Electronic Brake Control; ABS Control Module; Module, Electronic Brake Control
- Replaces: 10330278
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2003-2004 Buick Regal | LS | 6 Cyl 3.8 L GAS
View related parts
Buick Regal Control Module Part Number: 16159331
Product Specifications
- Other Name: Module Assembly, Electronic Brake Control; ABS Control Module; ABS Control Unit; Module, Electronic Brake Control
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1988-1991 Buick Regal | Custom, Gran Sport, Limited | 6 Cyl 2.8 L GAS, 6 Cyl 3.1 L GAS, 6 Cyl 3.8 L GAS
View related parts
Buick Regal Control Module Part Number: 12214535
Product Specifications
- Other Name: Module, Electronic Brake Control; ABS Control Module
- Replaces: 09377006, 09387336, 12208996, 9377006, 9387336
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1999-2000 Buick Regal | GS, GSE, LS, LSE | 6 Cyl 3.8 L GAS
View related parts
Buick Regal Control Module Part Number: 9350281
Product Specifications
- Other Name: Module Assembly, Electronic Brake Control; ABS Control Module; Module, Electronic Brake Control
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1997-1998 Buick Regal | 25th Anniversary Edition, GS, LS | 6 Cyl 3.8 L GAS
View related parts
Buick Regal Control Module Part Number: 16209171
Product Specifications
- Other Name: Module Assembly-Electronic Brake Control; ABS Control Module; Module, Electronic Brake Control
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1995 Buick Regal | Custom, Gran Sport, Limited | 6 Cyl 3.1 L GAS, 6 Cyl 3.8 L GAS
View related parts
Buick Regal Control Module Part Number: 16240521
Product Specifications
- Other Name: Module; ABS Control Module; ABS Control Unit
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1996 Buick Regal | Custom, Gran Sport, Limited, Olympic Gold Edition | 6 Cyl 3.1 L GAS, 6 Cyl 3.8 L GAS
View related parts
Buick Regal Motor Assembly Part Number: 18024456
Product Specifications
- Other Name: Motor Kit, Electronic Brake Control; ABS Pump And Motor Assembly; Motor & Pump; Motor
- Replaces: 18019214
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1992-1996 Buick Regal | Custom, Gran Sport, Limited, Olympic Gold Edition | 6 Cyl 3.1 L GAS, 6 Cyl 3.8 L GAS
View related parts
Buick Regal Control Module Part Number: 12225454
Product Specifications
- Other Name: Module Assembly, Electronic Brake Control; ABS Control Module; Module, Electronic Brake Control
- Replaces: 12201162, 12214522
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2002 Buick Regal | LS | 6 Cyl 3.8 L GAS
View related parts
Buick Regal Control Module Part Number: 16154594
Product Specifications
- Other Name: Module Assembly, Electronic Brake Control; ABS Control Module; ABS Control Unit; Module, Electronic Brake Control
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1992 Buick Regal | Custom, Gran Sport, Limited | 6 Cyl 3.1 L GAS, 6 Cyl 3.8 L GAS
View related parts
Buick Regal Control Module Part Number: 12214532
Product Specifications
- Other Name: Module, Electronic Brake Control; ABS Control Module
- Replaces: 09387339, 09377480, 09378276, 12209440, 9378276, 9387339, 9377480
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1999-2000 Buick Regal | GS, GSE | 6 Cyl 3.8 L GAS
View related parts
Buick Regal Control Module Part Number: 18078144
Product Specifications
- Other Name: Module Assembly, Electronic Brake & Traction Control; ABS Control Module; Module, Electronic Brake Control
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2003-2004 Buick Regal | GS | 6 Cyl 3.8 L GAS
View related parts
Buick Regal Control Module Part Number: 12214534
Product Specifications
- Other Name: Module, Electronic Brake Control; ABS Control Module
- Replaces: 09377007, 09387338, 12209434, 9377007, 9387338
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1999-2001 Buick Regal | LS, LSE | 6 Cyl 3.8 L GAS
View related parts
Buick Regal Control Module Part Number: 12224471
Product Specifications
- Other Name: Module Assembly, Electronic Brake & Traction Control; ABS Control Module; Module, Electronic Brake Control
- Replaces: 12214202
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2001-2002 Buick Regal | GS | 6 Cyl 3.8 L GAS
View related parts
Buick Regal Control Module Part Number: 18078135
Product Specifications
- Other Name: Module Assembly, Electronic Brake Control; ABS Control Module; Modulator; Module, Electronic Brake Control
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2004 Buick Regal | GS, LS | 6 Cyl 3.8 L GAS
View related parts
Buick Regal Control Module Part Number: 16176728
Product Specifications
- Other Name: Module Assembly, Electronic Brake Control; ABS Control Module; ABS Control Unit; Module, Electronic Brake Control
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1993 Buick Regal | Custom, Gran Sport, Limited | 6 Cyl 3.1 L GAS, 6 Cyl 3.8 L GAS
View related parts
Buick Regal Control Module Part Number: 16203633
Product Specifications
- Other Name: Module Assembly, Electronic Brake Control; ABS Control Module; ABS Control Unit; Module, Electronic Brake Control
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1995 Buick Regal | Custom, Gran Sport, Limited | 6 Cyl 3.1 L GAS, 6 Cyl 3.8 L GAS
View related parts
Buick Regal Control Module Part Number: 16240001
Product Specifications
- Other Name: Module, Electronic Brake Control; ABS Control Module; ABS Control Unit
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1996 Buick Regal | Custom, Gran Sport, Limited, Olympic Gold Edition | 6 Cyl 3.1 L GAS, 6 Cyl 3.8 L GAS
View related parts
Buick Regal Control Module Part Number: 9355411
Product Specifications
- Other Name: Module Assembly-Electronic Brake & Traction Control; ABS Control Module; Module, Electronic Brake Control
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1997-1998 Buick Regal | GS, LS | 6 Cyl 3.8 L GAS

| Page 1 of 2 |Next >

1-20 of 34 Results

Buick Regal ABS Control Module

Want to cut long-term maintenance and repair costs? Choose OEM ABS Control Module. Those parts deliver top durability you can trust. On our site, you'll find a huge catalog of genuine Buick Regal parts. Prices are unbeatable, so you can keep more in your pocket. Every OEM Buick Regal ABS Control Module includes a manufacturer's warranty. You can also get an easy return policy that keeps buying risk free. Fast delivery, get your car on the road quickly. It's simple to search, compare, and order. Stop guessing about quality or fit. Order today and save with parts that last.

The Buick Regal ABS Control Module is one of the critical parts which demonstrates Buick's responsibility and its vehicles' performance. This module aims to improve the braking performance and safety by avoiding wheel locking when the car is heavily braked, and thus the Buick Regal is going to remain securely stick to the surface of the road. Serving multiple Regal models, the ABS Control Module integrates with the help of the signals of speed sensors, valves, and a pump and provides adjustments in brake pressure. This highly developed and complex system not only eliminates skidding but also includes superior elements like the electronic stability control and traction control that pushes up the safety of the Buick Regal to another level. Thus, the said Buick Regal ABS Control Module is highly admirable due to its sturdiness and functionality in contributing to the unique identity of automobiles in the market. Through its capacity of signaling alterations in the drive conditions, the ABS control module makes it possible for drivers to glide in their Buick Regal with the assurance that they car has top notch technologies. Even as the Regal IN has developed through the years, the ABS Control Module has constantly been an important component of the car's building process, which is why Buick cannot be mentioned as a company that has not shown deep commitment to superior technology and quality. Regardless of the choice of either the base model Regal Custom or the sportier Gran Sport version, the ABS Control Module is central to the Regal brand's reputation for performance and safety.

Buick Regal ABS Control Module Parts and Q&A

Control Module
18078132
Q: How to replace the ABS Control Module on Buick Regal?
A:
You should start the ABS Control Module (ABSCM) replacement process by setting the ignition switch to off because this stops equipment damage from occurring. The first step requires eliminating the fuel injector sight shield from 3.8 l engines followed by removal of the front fender upper diagonal brace. Accomplish disconnecting first the Cruise Control Module from the left strut tower along with the accelerator control cable from its bracket without cutting the cable. Set aside the module and cables in their current locations. The procedure starts with removing the air cleaner intake duct followed by loosening the red locking tab from the connector lock tab. Subsequently detach the abscm harness connector by moving the sliding connector cover to the open position. Clean the component assembly and separate the four abscm to bpmv retainers while taking precautions against toolkit damage to the bpmv surface or solenoid valves. The abscm separation from bpmv should be conducted without excessive force. Attach the abscm to the bpmv while installing four retainers that require tightening to 5 nm (44 inch lbs.). Next step is to connect the abscm harness connector while pushing down the lock tab until you reach the locked position which reengages the red locking tab. After that, reinstall the air cleaner intake duct along with the module and cables and connect the Cruise Control Module at the left strut tower. Reposition the accelerator and cruise control cable to its bracket on the accelerator control cable bracket while also installing the front fender upper diagonal brace and fuel injector sight shield which applies to 3.8l engine models only. End the procedure by using the ignition key to access the run position without starting the engine and initiating the diagnostic system check - abs.
Control Module
12214535
Q: How to Safely Remove and Install the ABS Control Module on Buick Regal?
A:
The removal process for ABS Control Module (ABSCM) begins with setting the Ignition Switch to off to protect equipment components. First unlock the connector lock tab with your finger by pulling out its red locking tab. After that, push down on lock tab followed by sliding connector cover into an open position to disconnect the abscm harness connector. The assembly cleaning process requires dirt removal before the four abscm to bpmv screws are removed to separate the abscm from the bpmv while maintaining a tool-free separation of the abscm from the bpmv surface and solenoid valves. First clean the bpmv surface with alcohol using a cleaned rag and then mount the abscm to bpmv while tightening its installing screws to 5 nm (44 inch lbs.). Reconnecting the abscm harness connector should be followed by pressing the lock tab while sliding the connector cover until it reaches its locked position before completing with the red locking tab. Conclude by activating the Ignition Switch to run without engine start to execute the a diagnostic system check-abs.