How to replace the inner CV Boot and CV Joint on Cadillac DeVille?

To replace the wheel's drive shaft inner joint and the boot, first, gather necessary tools for the procedure: snap ring pliers (J8059), seal clamp designed tool (J35910) and earless seal clamp tool (J35566). Examine the sealing surface of the halfshaft transmission after its removal for corrosion; clean any corrosion with 320 grit cloth or equivalent a using transmission fluid as needed and ensure that the surface is dry before you re-install the half-shaft. If you don't damage the sealing surface of the outer housing or of the trilobal tripot bushing, remove and throw away the boot retainer clamp as well as the large boot retaining clamp from the halfshaft bar and tripot joint, respectively. Detach the halfshaft inboard boot from the trilobal tripot bushing and slide the boot from the joint and remove the housing from the tripot joint spider and half shaft-bar. Clean the tripot balls, needle rollers, and housing with a solvent, eliminating all old grease and contaminants, and check out the half shaft inboard boot, tripot joint spider assembly, housing, trilobal tripot bushing, and needle rollers for damages or wear. Put the small boot retaining clamp on the inboard boot with no crimping and slide the boot on to the halfshaft bar and position it in the boot groove. Tighten the boot retaining clamp using the seal clamp tool (J35910) to 136 nm (100 ft. Lbs.) and measure the gap dimension. Mount the spacer ring over the halfshaft bar and push the tripot joint spider assembly back onto it. Use snap ring pliers (J8059) to install the halfshaft bar retaining ring and slide the spider assembly toward the end of the bar and re-seat the first spacer ring. Put a half of the grease from the service kit in the boot and leave the other half for re-packing the housing. Mount the trilobal tripot bushing to the housing flush, and mount the larger new clamp on the boot. Slip the housing onto the spider assembly, ensuring the boot is shaped and sitting in the groove. Align the boot, housing, and the large clamp by latching it, and finally, latch the boot retaining clamp using the earless seal clamp tool (J35566).

OEM Cadillac DeVille CV Boot

Axle Boot

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

19 CV Boots found

View related parts
Cadillac DeVille Boot Kit, Front Part Number: 20984614
$36.52 MSRP: $92.67
You Save: $56.15 (61%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Boot Kit, Front Wheel Drive Axle Shaft; CV Boot; Inner CV Joint Boot; Inner Boot; Boots
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2004 Cadillac DeVille | Base, DHS, DTS, Protection Series | 8 Cyl 4.6 L GAS
View related parts
Cadillac DeVille Boot Kit, Front Part Number: 15269918
Product Specifications
- Other Name: Boot Kit, Front Wheel Drive Axle Shaft; CV Boot; Outer CV Joint Boot; Outer Boot; Inner Boot Kit; Boots; Boot Kit, Front Axle
- Position: Front
- Replaces: 89047671
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2005 Cadillac DeVille | Base, DHS, DTS, Protection Series | 8 Cyl 4.6 L GAS
View related parts
Cadillac DeVille Seal Kit, Front Part Number: 26059842
Product Specifications
- Other Name: Boot Kit, Front Axle; CV Boot; CV Joint Boot Kit for Front Wheel Drive Axle Shaft; includes outer and inner seals.
- Position: Front
- Replaces: 26099016
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1994-1995, 1985-1992 Cadillac DeVille | Base, Cabriolet, d'Elegance, Spring Edition, Touring | 6 Cyl 4.3 L DIESEL, 8 Cyl 4.1 L GAS, 8 Cyl 4.5 L GAS, 8 Cyl 4.9 L GAS
View related parts
Cadillac DeVille Axle Boots, Front Part Number: 26030761
Product Specifications
- Other Name: Boot Kit, Front Wheel Drive Axle Shaft; CV Boot; Boot Kit; Outer CV Joint Boot; Inner Boot; Boots
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1994-1995 Cadillac DeVille | Concours | 8 Cyl 4.6 L GAS
View related parts
Cadillac DeVille Boot Kit Part Number: 89060343
Product Specifications
- Other Name: Boot Kit, Front Wheel Drive Axle Shaft; CV Boot; Inner CV Joint Boot; Inner Boot; Boots; Boot Kit, Front Axle
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2005 Cadillac DeVille | Base, DHS, DTS, Protection Series | 8 Cyl 4.6 L GAS
View related parts
Cadillac DeVille Seal Kit, Passenger Side Part Number: 7847110
Product Specifications
- Other Name: Seal Kit - Tripot (High-Temperature); Axle Seal; CV Boot; CV Joint Boot Kit; Boot Kit; Boots; Boot Kit, Front Wheel Drive Axle Shaft
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1985 Cadillac DeVille | Base, Cabriolet, d'Elegance | 6 Cyl 4.3 L DIESEL, 8 Cyl 4.1 L GAS
View related parts
Cadillac DeVille Seal Kit Part Number: 7845021
Product Specifications
- Other Name: Boot Kit- C/V; CV Boot; CV Joint Boot Kit; Boot Kit; Boots; Seal; Boot
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1985 Cadillac DeVille | Base, Cabriolet, d'Elegance | 6 Cyl 4.3 L DIESEL, 8 Cyl 4.1 L GAS
View related parts
Cadillac DeVille Seal Kit, Driver Side Part Number: 7843924
Product Specifications
- Other Name: Axle Seal; CV Boot; Boot Kit; Boots
- Position: Driver Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1985 Cadillac DeVille | Base, Cabriolet, d'Elegance | 6 Cyl 4.3 L DIESEL, 8 Cyl 4.1 L GAS
View related parts
Cadillac DeVille Seal Kit Part Number: 26044380
Product Specifications
- Other Name: Boot, Front; Axle Seal; CV Boot; Boot Kit; Outer CV Joint Boot; Inner Boot; Outer Boot; Outer Boot Kit; Boots; Boot
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1995 Cadillac DeVille | Base | 8 Cyl 4.9 L GAS
View related parts
Cadillac DeVille CV Joint Boot Kit Part Number: 26020951
Product Specifications
- Other Name: CV Boot; Boots
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1991 Cadillac DeVille | Base, Spring Edition, Touring | 8 Cyl 4.9 L GAS
View related parts
Cadillac DeVille Inner Boot, Front Part Number: 26075586
Product Specifications
- Other Name: Boot Kit, Front Wheel Drive Axle Shaft; CV Boot
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2005 Cadillac DeVille | Base, DHS, DTS, Protection Series | 8 Cyl 4.6 L GAS
View related parts
Cadillac DeVille Outer Boot, Front Part Number: 26063829
Product Specifications
- Other Name: Boot Kit, Front Axle; CV Boot; Boot Kit, Front Wheel Drive Axle Shaft
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2005 Cadillac DeVille | Base, DHS, DTS, Protection Series | 8 Cyl 4.6 L GAS
View related parts
Cadillac DeVille Boot Kit, Front Part Number: 26060112
Product Specifications
- Other Name: Boot Kit, Front Wheel Drive Axle Shaft; CV Boot; Inner CV Joint Boot; Inner Boot; Boots
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1999 Cadillac DeVille | Base, Concours, d'Elegance | 8 Cyl 4.6 L GAS
View related parts
Cadillac DeVille Boot Kit, Front Part Number: 26044385
Product Specifications
- Other Name: Boot Kit, Front Wheel Drive Axle Shaft; CV Boot; Inner CV Joint Boot; Inner Boot; Boots
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1995-1999 Cadillac DeVille | Base, Concours, d'Elegance | 8 Cyl 4.6 L GAS
View related parts
Cadillac DeVille Boot Kit, Front Part Number: 26044384
Product Specifications
- Other Name: Boot Kit, Front Wheel Drive Axle Shaft; CV Boot
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1995 Cadillac DeVille | Base | 8 Cyl 4.9 L GAS
View related parts
Cadillac DeVille Boot Kit, Front Part Number: 26044383
Product Specifications
- Other Name: Boot Kit, Front Axle; CV Boot; Outer CV Joint Boot; Outer Boot; Outer Boot Kit; Boots; Boot Kit, Front Wheel Drive Axle Shaft
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1995-2004 Cadillac DeVille | Base, Concours, d'Elegance, DHS, DTS, Protection Series | 8 Cyl 4.6 L GAS
View related parts
Cadillac DeVille Axle Boots, Front Part Number: 26030762
Product Specifications
- Other Name: Boot Kit, Front Axle; CV Boot; Boot Kit; Inner CV Joint Boot; Outer Boot; Boots; Boot Kit, Front Wheel Drive Axle Shaft
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1994-1995 Cadillac DeVille | Concours | 8 Cyl 4.6 L GAS
View related parts
Cadillac DeVille Seal Kit, Front Part Number: 26007428
Product Specifications
- Other Name: Boot Kit, Front Wheel Drive Axle Shaft; Axle Seal; CV Boot; Axle Boots; Boot Kit; Inner CV Joint Boot; Inner Boot; Boots
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1988-1995 Cadillac DeVille | Base, Spring Edition, Touring | 8 Cyl 4.5 L GAS, 8 Cyl 4.9 L GAS
View related parts
Cadillac DeVille Seal Kit, Front Part Number: 26001938
Product Specifications
- Other Name: Boot Kit, Front Wheel Drive Axle Shaft; CV Joint Boot Kit; includes axle boots, inner and outer seals for front wheel drive axle shaft.
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1989-1993, 1985-1987 Cadillac DeVille | Base, Cabriolet, d'Elegance, Spring Edition, Touring | 6 Cyl 4.3 L DIESEL, 8 Cyl 4.1 L GAS, 8 Cyl 4.5 L GAS, 8 Cyl 4.9 L GAS

Cadillac DeVille CV Boot

Want to cut long-term maintenance and repair costs? Choose OEM CV Boot. Those parts deliver top durability you can trust. On our site, you'll find a huge catalog of genuine Cadillac DeVille parts. Prices are unbeatable, so you can keep more in your pocket. Every OEM Cadillac DeVille CV Boot includes a manufacturer's warranty. You can also get an easy return policy that keeps buying risk free. Fast delivery, get your car on the road quickly. It's simple to search, compare, and order. Stop guessing about quality or fit. Order today and save with parts that last.

The CV Boot of Cadillac DeVille vehicles is an essential part that shields the Constant Velocity (CV) Joint that transfers power from transaxle to wheels. The CV Boot is an expandable rubber or plastic casing which contains lubricant for the joints and which protects those joints from environmental conditions. Some of the CV Joints applied on DeVille vehicles include the non-adjustable joints on the outer part of the axle, and sideways plunging joints on the internal part. Rzeppa joint is often used in the application of outboard CV Joint while tripod and double offset joints are used for the inboard ones. Thereby, the CONSTREET CV Boot needs to be inspected regularly as damaged boots lead to CV Joint problems such as squeaking or knocking sounds whenever the vehicle is turning and jolting with every acceleration.

Cadillac DeVille CV Boot Parts Questions & Experts Answers

Boot Kit, Front
20984614
Q: How to replace the inner CV Boot and CV Joint on Cadillac DeVille?
A:
To replace the wheel's drive shaft inner joint and the boot, first, gather necessary tools for the procedure: snap ring pliers (J8059), seal clamp designed tool (J35910) and earless seal clamp tool (J35566). Examine the sealing surface of the halfshaft transmission after its removal for corrosion; clean any corrosion with 320 grit cloth or equivalent a using transmission fluid as needed and ensure that the surface is dry before you re-install the half-shaft. If you don't damage the sealing surface of the outer housing or of the trilobal tripot bushing, remove and throw away the boot retainer clamp as well as the large boot retaining clamp from the halfshaft bar and tripot joint, respectively. Detach the halfshaft inboard boot from the trilobal tripot bushing and slide the boot from the joint and remove the housing from the tripot joint spider and half shaft-bar. Clean the tripot balls, needle rollers, and housing with a solvent, eliminating all old grease and contaminants, and check out the half shaft inboard boot, tripot joint spider assembly, housing, trilobal tripot bushing, and needle rollers for damages or wear. Put the small boot retaining clamp on the inboard boot with no crimping and slide the boot on to the halfshaft bar and position it in the boot groove. Tighten the boot retaining clamp using the seal clamp tool (J35910) to 136 nm (100 ft. Lbs.) and measure the gap dimension. Mount the spacer ring over the halfshaft bar and push the tripot joint spider assembly back onto it. Use snap ring pliers (J8059) to install the halfshaft bar retaining ring and slide the spider assembly toward the end of the bar and re-seat the first spacer ring. Put a half of the grease from the service kit in the boot and leave the other half for re-packing the housing. Mount the trilobal tripot bushing to the housing flush, and mount the larger new clamp on the boot. Slip the housing onto the spider assembly, ensuring the boot is shaped and sitting in the groove. Align the boot, housing, and the large clamp by latching it, and finally, latch the boot retaining clamp using the earless seal clamp tool (J35566).