How to replace the rear wheel bearing and wheel hub (FE7) on Cadillac DeVille?

Use a lift to support the vehicle and remove its wheel with tire before replacing its rear wheel bearing and hub fe7 part. To begin, unmount the brake caliper with its two bolts and hang it aside from the rotor before taking out the brake rotor. Unplug the ABS Sensor wire connector then take out the harness. Disconnect the Parking Brake Cable from the Control Arm. Separate the ABS Sensor from its hookup before you detach the four bearing retainer bolts and the reluctor. Unbolt the hub and bearing and also remove the wheel bearing if needed. Next detach the brake shield and wheel bearing. Position the wheel bearing inside the hub and put on the washer and bearing nut. Tighten the wheel bearing assembly nut to 147 foot-pounds torque. Insert a new hub and bearing into the Control Arm bore then fasten four bolts to 118 nm. Replace both the reluctor disc and ABS Sensor components before putting back the brake rotor and caliper. Once done connect the ABS Sensor wire then put on the wheel and tire while tightening wheel nuts to 125 nm (80 ft. Lbs.). Lower the vehicle afterward.

How to Replace the Front Wheel Bearing and Wheel Hub (FE1, FE3) on Cadillac DeVille?

Before working on the front wheel bearing and hub you need to lift the vehicle and keep it stable. After removing the wheel include a big flat tool in the caliper and rotor to block rotation as you disconnect the tire and wheel. Begin the procedure by taking apart both the wheel drive shaft nut and rotor component. Pull off the speed sensor connector from the dust shield and release it from the front wheel speed sensor. The front/rear spindle remover tool j 28733-b helps you take out the wheel bearing and hub retaining bolts. Once removed insert the tool to separate the wheel bearing and hub from the drive axle. Thoroughly clean the knuckle mating surface as well as the bore and chamfer of the wheel bearing face when preparing the installation space. For this task only use a light grease layer and avoid handling the wheel bearing hub near the abs sensor wire. Use the dust shield without harming the bearing lip seal and install the wheel bearing and hub unit onto the drive axle by spreading a thin layer of grease on the steering knuckle bore. Screw the drive axle nut to move the wheel bearing and hub onto the axle, then connect wheel bearing and hub mounting bolts and tighten them to 130 nm (96 ft. Lbs.). Secure the front wheel speed sensor connector to its dust shield position then put the rotor in place. To keep the rotor from spinning use the large flat tool inserted at the caliper space then torque the wheel drive shaft nut to 160 nm. Place the tire on the wheel and lower the car to its normal position.

OEM Cadillac DeVille Wheel Hub

Wheel Axle Hub

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

14 Wheel Hubs found

View related parts
Cadillac DeVille Hub Assembly, Rear Part Number: 7470555
$110.87 MSRP: $206.90
You Save: $96.03 (47%)
ADD TO CART
Product Specifications
- Other Name: Hub, Rear Wheel (W/Wheel Speed Sensor); Wheel Bearing & Hub Assembly; Axle Bearing.; Rear Hub & Bearing Assembly; Hub & Bearing; Hub & Bearing Assembly; Rotor Hub & Bearing; Hub; Hub, Rear Wheel
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2005 Cadillac DeVille | Base, DHS, DTS, Protection Series | 8 Cyl 4.6 L GAS
View related parts
Cadillac DeVille Front Hub & Bearing Assembly Part Number: 7470511
$199.93 MSRP: $361.87
You Save: $161.94 (45%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Hub, Front Wheel; Wheel Bearing & Hub Assembly; Repair Kit; Axle Bearing.; Hub & Bearing; Hub & Bearing Assembly; Rotor Hub & Bearing; Hub
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1992-1996 Cadillac DeVille | Base, Concours, d'Elegance, Touring | 8 Cyl 4.6 L GAS, 8 Cyl 4.9 L GAS
View related parts
Cadillac DeVille Hub Assembly, Front Part Number: 84641365
$223.57 MSRP: $433.94
You Save: $210.37 (49%)
Ships in 1 Business Day
ADD TO CART
Product Specifications
- Other Name: Hub Assembly, Front Wheel (W/Wheel Speed Sensor); Front Hub & Bearing; Front Wheel Hub Kit; Rear Wheel Hub
- Position: Front
- Replaced by: 19433930
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2001-2005 Cadillac DeVille | Base, DHS, DTS, Protection Series | 8 Cyl 4.6 L GAS
View related parts
Cadillac DeVille Hub Assembly, Front Part Number: 12429204
$223.57 MSRP: $433.94
You Save: $210.37 (49%)
Ships in 1 Business Day
ADD TO CART
Product Specifications
- Other Name: Hub Kit, Front Wheel; Wheel Bearing & Hub Assembly; Disc Brake Hardware Kit; Wheel Hub Repair Kit; Axle Bearing.; Front Hub & Bearing; Front Hub; Hub & Bearing; Hub Kit, Rear Wheel
- Position: Front
- Replaced by: 19433930
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1997-2000 Cadillac DeVille | Base, Concours, d'Elegance, DHS, DTS | 8 Cyl 4.6 L GAS
View related parts
Cadillac DeVille Hub Assembly, Rear Part Number: 7470543
Product Specifications
- Other Name: Hub, Rear Wheel; Wheel Bearing and Hub Assembly; Wheel Bearing & Hub Assembly; Wheel Bearing; Axle Bearing; Wheel Hub; Rear Hub & Bearing Assembly; Hub & Bearing; Rotor Hub & Bearing
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1994-1999 Cadillac DeVille | Base, Concours, d'Elegance | 8 Cyl 4.6 L GAS, 8 Cyl 4.9 L GAS
View related parts
Cadillac DeVille Hub & Bearing Assembly Part Number: 7466949
Product Specifications
- Other Name: Hub Assembly; Wheel Bearing and Hub Assembly; Wheel Bearing & Hub Assembly; Wheel Bearing; Axle Bearing
- Replaced by: 12413025
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1986-1991 Cadillac DeVille | Base, d'Elegance, Spring Edition, Touring | 8 Cyl 4.1 L GAS, 8 Cyl 4.5 L GAS, 8 Cyl 4.9 L GAS
View related parts
Cadillac DeVille Rear Bearing Part Number: 7470595
Product Specifications
- Other Name: Hub Assembly, Rear Wheel; Wheel Hub Repair Kit; Wheel Bearing; Axle Bearing; Wheel Hub; Hub & Bearing; Hub & Bearing Assembly; Hub, Rear Wheel
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1988-1993 Cadillac DeVille | Base, Spring Edition, Touring | 8 Cyl 4.5 L GAS, 8 Cyl 4.9 L GAS
View related parts
Cadillac DeVille Front Hub & Bearing Assembly Part Number: 7470593
Product Specifications
- Other Name: Hub Assembly, Front Wheel; Wheel Hub Repair Kit; Wheel Bearing; Axle Bearing; Wheel Hub; Front Hub & Bearing; Hub & Bearing; Hub, Front Wheel
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1990-1993 Cadillac DeVille | Base, Spring Edition, Touring | 8 Cyl 4.5 L GAS, 8 Cyl 4.9 L GAS
View related parts
Cadillac DeVille Wheel Bearing, Rear Part Number: 7470573
Product Specifications
- Other Name: Hub Assembly, Rear Wheel; Axle Bearing; Wheel Hub; Hub & Bearing; Hub, Rear Wheel
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1986 Cadillac DeVille | d'Elegance, Touring | 8 Cyl 4.1 L GAS
View related parts
Cadillac DeVille Hub & Bearing, Front Part Number: 7470553
Product Specifications
- Other Name: Hub, Front W; Wheel Bearing & Hub Assembly; Repair Kit; Axle Bearing.; Hub, Front Wheel
- Position: Front
- Replaces: 7466977
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1992-1993 Cadillac DeVille | Base, Touring | 8 Cyl 4.9 L GAS
View related parts
Cadillac DeVille Rear Bearing Part Number: 7470541
Product Specifications
- Other Name: Hub, Rear Wheel; Wheel Bearing and Hub Assembly; Repair Kit; Axle Bearing.; Hub & Bearing; Hub
- Position: Rear
- Replaces: 7466968
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1991-1993 Cadillac DeVille | Base, Spring Edition, Touring | 8 Cyl 4.9 L GAS
View related parts
Cadillac DeVille Wheel Bearing, Rear Part Number: 7470503
Product Specifications
- Other Name: Hub Assembly, Rear Wheel; Wheel Bearing & Hub Repair Kit; Axle Bearing.; Hub Assembly; Bearing Assembly; Rear Bearing; Hub & Bearing; Hub; Hub, Rear Wheel
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1985-1993 Cadillac DeVille | Base, Cabriolet, d'Elegance, Spring Edition, Touring | 6 Cyl 4.3 L DIESEL, 8 Cyl 4.1 L GAS, 8 Cyl 4.5 L GAS, 8 Cyl 4.9 L GAS
View related parts
Cadillac DeVille Wheel Bearing, Front Part Number: 7470003
Product Specifications
- Other Name: Hub, Front Wheel (W/Bearing); Wheel Bearing & Hub Assembly; Repair Kit; Axle Bearing.; Front Wheel Bearing; Hub & Bearing Assembly; Rear Hub Bearings; Rotor Hub & Bearing.
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1985-1992 Cadillac DeVille | Base, Cabriolet, d'Elegance, Spring Edition, Touring | 6 Cyl 4.3 L DIESEL, 8 Cyl 4.1 L GAS, 8 Cyl 4.5 L GAS, 8 Cyl 4.9 L GAS
View related parts
Cadillac DeVille Wheel Bearing, Rear Part Number: 12413025
Product Specifications
- Other Name: Hub Assembly, Rear Wheel; Wheel Bearing & Hub Repair Kit; Axle Bearing.; Rear Hub & Bearing Assembly; Hub & Bearing; Rotor Hub & Bearing; Hub; Hub, Rear Wheel
- Position: Rear
- Replaces: 7470579, 07470579, 7466949
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1986-1991 Cadillac DeVille | Base, Spring Edition, Touring, d'Elegance | 8 Cyl 4.1 L GAS, 8 Cyl 4.5 L GAS, 8 Cyl 4.9 L GAS

Cadillac DeVille Wheel Hub

Want to cut long-term maintenance and repair costs? Choose OEM Wheel Hub. Those parts deliver top durability you can trust. On our site, you'll find a huge catalog of genuine Cadillac DeVille parts. Prices are unbeatable, so you can keep more in your pocket. Every OEM Cadillac DeVille Wheel Hub includes a manufacturer's warranty. You can also get an easy return policy that keeps buying risk free. Fast delivery, get your car on the road quickly. It's simple to search, compare, and order. Stop guessing about quality or fit. Order today and save with parts that last.

The Wheel Hub of Cadillac DeVille automobiles is a component that couples the wheel to the vehicle and those automobile parts that include the bearings, sensors, and brakes. Some of the types of wheel hubs include, unit assembly wheel hub bearing with bearings integration and non-driven axle wheel hub with replaceable type of the tapered roller bearings. Appropriate care of Wheel Hubs is crucial since, when the bearings are worn, several symptoms such as noise or vibration and also possible wheel loss may occur. Bi-annual and or annual checks and applying replacements where necessary are strongly encouraged in order to have the vehicle in its premier condition as well as safety. Cadillac DeVille Wheel Hubs are one of the housings for the wheels that enable the rotation of wheels and their secure fitting on the car, thus affecting its performance and sturdiness.

Cadillac DeVille Wheel Hub Parts and Q&A

Hub Assembly, Rear
7470555
Q: How to replace the rear wheel bearing and wheel hub (FE7) on Cadillac DeVille?
A:
Use a lift to support the vehicle and remove its wheel with tire before replacing its rear wheel bearing and hub fe7 part. To begin, unmount the brake caliper with its two bolts and hang it aside from the rotor before taking out the brake rotor. Unplug the ABS Sensor wire connector then take out the harness. Disconnect the Parking Brake Cable from the Control Arm. Separate the ABS Sensor from its hookup before you detach the four bearing retainer bolts and the reluctor. Unbolt the hub and bearing and also remove the wheel bearing if needed. Next detach the brake shield and wheel bearing. Position the wheel bearing inside the hub and put on the washer and bearing nut. Tighten the wheel bearing assembly nut to 147 foot-pounds torque. Insert a new hub and bearing into the Control Arm bore then fasten four bolts to 118 nm. Replace both the reluctor disc and ABS Sensor components before putting back the brake rotor and caliper. Once done connect the ABS Sensor wire then put on the wheel and tire while tightening wheel nuts to 125 nm (80 ft. Lbs.). Lower the vehicle afterward.
Hub Assembly, Front
84641365
Q: How to Replace the Front Wheel Bearing and Wheel Hub (FE1, FE3) on Cadillac DeVille?
A:
Before working on the front wheel bearing and hub you need to lift the vehicle and keep it stable. After removing the wheel include a big flat tool in the caliper and rotor to block rotation as you disconnect the tire and wheel. Begin the procedure by taking apart both the wheel drive shaft nut and rotor component. Pull off the speed sensor connector from the dust shield and release it from the front wheel speed sensor. The front/rear spindle remover tool j 28733-b helps you take out the wheel bearing and hub retaining bolts. Once removed insert the tool to separate the wheel bearing and hub from the drive axle. Thoroughly clean the knuckle mating surface as well as the bore and chamfer of the wheel bearing face when preparing the installation space. For this task only use a light grease layer and avoid handling the wheel bearing hub near the abs sensor wire. Use the dust shield without harming the bearing lip seal and install the wheel bearing and hub unit onto the drive axle by spreading a thin layer of grease on the steering knuckle bore. Screw the drive axle nut to move the wheel bearing and hub onto the axle, then connect wheel bearing and hub mounting bolts and tighten them to 130 nm (96 ft. Lbs.). Secure the front wheel speed sensor connector to its dust shield position then put the rotor in place. To keep the rotor from spinning use the large flat tool inserted at the caliper space then torque the wheel drive shaft nut to 160 nm. Place the tire on the wheel and lower the car to its normal position.