How to replace the ignition control module for Bank 1 on Cadillac DeVille?

Begin Bank 1 Ignition Control Module replacement by first unbolting and removing the engine sight shield retaining bolts and engine sight shield. First detach the electrical connector which powers up the ignition control module. To perform the replacement you must start by disconnecting the AIR system vacuum hoses (labeling their original positions first) and remove the AIR pipe to exhaust manifold bolts. You must also disconnect the AIR vent solenoid electrical connector when removing the AIR assembly. Following the removal sequence remove the ignition assembly retaining bolts before carefully taking out the ignition assembly. First remove all ignition control module retaining screws before removing the module itself. Start by installing the ignition control module followed by tightening its retaining screws to 0.8 N.m (7 lb in). Place the ignition assembly insulation and grounding spring correctly then install the ignition assembly with retaining bolts tightened to 9 N.m (80 lb in). During installation of an engine with AIR features first add the AIR assembly before attaching the AIR bracket using proper torque settings for the bracket's bolts. Install the AIR vacuum hoses and the AIR pipe to exhaust manifold bolts and the AIR vent solenoid electrical connector when present. After lastly completing installation of the engine sight shield equipment tighten its retaining bolts up to 8 N.m (70 lb. in.) while also reconnecting the ignition assembly electrical connector.

How to replace the ignition coil and Ignition Control Module (HVS) on Cadillac Escalade?

To replace the Ignition Coil and Ignition Control Module (HVS), you need to remove the air cleaner assembly and nut then disconnecting the electrical connectors. Next, remove the Ignition Coil wire from the Distributor and remove the studs that hold the bracket and Ignition Coil on the Intake Manifold. Next, you will have to remove the bracket and Ignition Coil, drill and punch out the two rivets that are holding the Ignition Coil to the bracket, and then take the Ignition Coil away from the bracket. For installation, mount the Ignition Coil into the bracket with the two screws included in the replacement Ignition Coil kit. Replace the Ignition Coil and bracket onto Intake Manifold using studs, fastening them with 11 n.m (8 lb ft). Reconnect the wire from Ignition Coil, make sure, it does not touch any part such as dip stick in order to avoid grounding or shorting after passing time. Lastly, reconnect the electric connectors and replace the air cleaner assembly and nut.

OEM Cadillac Ignition Control Module

Ignition Spark Control Module

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

14 Ignition Control Modules found

View related parts
Cadillac Control Module Part Number: 10482803
$134.05 MSRP: $275.46
You Save: $141.41 (52%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Module, Electronic Ignition Control (W/O Coil); Ignition Control Module; Ignition Module; ESC Control Module; Coil Module; Module
- Replaced by: 19435467
Fits the following Cadillac Models:
- Escalade | 1999-2000 | Base | 8 Cyl 5.7 L GAS
- Fleetwood | 1996 | Base, Brougham | 8 Cyl 5.7 L GAS
View related parts
Cadillac Control Module Part Number: 19352932
$134.35 MSRP: $238.84
You Save: $104.49 (44%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Module Assembly, Electronic Ignition Control (W/O Coil); Ignition Control Module; Ignition Module; Coil Module; Module, Distributor (Also Knock Sensor)
- Replaces: 10483139, 16191409
Fits the following Cadillac Models:
- Fleetwood | 1994-1995 | Base, Brougham | 8 Cyl 5.7 L GAS
View related parts
Cadillac Ignition Lock Cylinder Part Number: 19179578
$75.52 MSRP: $155.20
You Save: $79.68 (52%)
ADD TO CART
Product Specifications
- Other Name: Module Assembly, Distributor Ignition Control; Ignition Control Module; Ignition Module; Module; Module, Distributor (Also Knock Sensor)
- Replaced by: 19435461
Fits the following Cadillac Models:
- Brougham | 1992 | Base, d'Elegance | 8 Cyl 5.0 L GAS, 8 Cyl 5.7 L GAS
- Fleetwood | 1993 | Base, Brougham | 8 Cyl 5.7 L GAS
View related parts
Cadillac Ignition Lock Cylinder Part Number: 19179581
$64.38 MSRP: $138.60
You Save: $74.22 (54%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Module Assembly, Distributor Ignition Control; Ignition Control Module; Ignition Module; Module; Module, Distributor (Also Knock Sensor)
- Replaced by: 19435464
- Replaces: 10457176, 10482832, 16140189, 16139869, 10482836, 10497133, 10456344, 10497132
Fits the following Cadillac Models:
- 60 Special | 1993 | Base | 8 Cyl 4.9 L GAS
- Allante | 1990-1992 | Base, Value Leader | 8 Cyl 4.5 L GAS
- Brougham | 1991 | Base, d'Elegance | 8 Cyl 5.0 L GAS, 8 Cyl 5.7 L GAS
- DeVille | 1991-1995 | Base, Spring Edition, Touring | 8 Cyl 4.9 L GAS
- Eldorado | 1992-1993 | Base, Touring | 8 Cyl 4.9 L GAS
- Fleetwood | 1991-1992 | 60 Special, Base, d'Elegance | 8 Cyl 4.9 L GAS
- Seville | 1986-1993 | Base, Elegante, STS | 8 Cyl 4.1 L GAS, 8 Cyl 4.5 L GAS, 8 Cyl 4.6 L GAS, 8 Cyl 4.9 L GAS
View More
View related parts
Cadillac Ignition Lock Cylinder Part Number: 19179579
$62.08 MSRP: $170.64
You Save: $108.56 (64%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Module Assembly, Distributor Ignition Control; Ignition Control Module; Ignition Module; Module; Module, Distributor (Also Knock Sensor)
- Replaces: 01987465, 10482828, 16139379, 1987465, 10457765
Fits the following Cadillac Models:
- Cimarron | 1985 | Base, d'Oro | 4 Cyl 2.0 L GAS
View related parts
Cadillac Glow Plug Controller Part Number: 98041624
$167.29 MSRP: $300.08
You Save: $132.79 (45%)
Product Specifications
- Other Name: Module Assembly-Glow Plug Control; Module, Spark Ignition
- Replaces: 98022489, 97371413
Fits the following Cadillac Models:
- Escalade | 2006 | Base | 8 Cyl 6.0 L GAS
- Escalade ESV | 2006 | Base | 8 Cyl 6.0 L GAS
- Escalade EXT | 2006 | Base | 8 Cyl 6.0 L GAS
View More
View related parts
Cadillac Ignition Module Part Number: 16126761
Product Specifications
- Other Name: Module, Windshield Defroster; Ignition Control Module; ESC Module; ESC Control Module; Module; Module, Distributor (Also Knock Sensor)
Fits the following Cadillac Models:
- Brougham | 1992 | Base, d'Elegance | 8 Cyl 5.0 L GAS
View related parts
Cadillac Control Module Part Number: 16214671
Product Specifications
- Other Name: Module, Distributor (Also Knock Sensor); Ignition Control Module; ESC Module; ESC Control Module
Fits the following Cadillac Models:
- Fleetwood | 1996 | Base, Brougham | 8 Cyl 5.7 L GAS
View related parts
Cadillac Control Module Part Number: 16188309
Product Specifications
- Other Name: Module, Distributor (Also Knock Sensor); Ignition Control Module; ESC Control Module
Fits the following Cadillac Models:
- Fleetwood | 1994-1995 | Base, Brougham | 8 Cyl 5.7 L GAS
View related parts
Cadillac Ignition Module Part Number: 19178832
Product Specifications
- Other Name: Module Assembly, Electronic Ignition Control (W/O Coil); Ignition Control Module; Module, Distributor (Also Knock Sensor)
- Replaces: 10477276, 10477066
Fits the following Cadillac Models:
- DeVille | 1994-2000 | Base, Concours, d'Elegance, DHS, DTS | 8 Cyl 4.6 L GAS
- Eldorado | 1993-1999 | Base, ESC, ETC, Sport, Touring | 8 Cyl 4.6 L GAS
- Seville | 1993-1999 | SLS, STS | 8 Cyl 4.6 L GAS
View More
View related parts
Cadillac Ignition Module Part Number: 16251879
Product Specifications
- Other Name: Module, Distributor (Also Knock Sensor); Ignition Control Module; Spark Module; ESC Control Module; Module
Fits the following Cadillac Models:
- Escalade | 1999-2000 | Base | 8 Cyl 5.7 L GAS
View related parts
Cadillac Spark Module Part Number: 16196410
Product Specifications
- Other Name: Module, Distributor (Also Knock Sensor); Ignition Control Module; Knock Sensor Module; ESC Control Module; Module
Fits the following Cadillac Models:
- DeVille | 1996-1999 | Base, Concours, d'Elegance | 8 Cyl 4.6 L GAS
- Eldorado | 1996-1999 | Base, ESC, ETC | 8 Cyl 4.6 L GAS
- Seville | 1996-1999 | SLS, STS | 8 Cyl 4.6 L GAS
View More
View related parts
Cadillac Spark Module Part Number: 16128261
Product Specifications
- Other Name: Module, Windshield Defroster; Ignition Control Module; ESC Control Module; Module; Module, Distributor (Also Knock Sensor)
- Replaces: 16052401
Fits the following Cadillac Models:
- Brougham | 1992 | Base, d'Elegance | 8 Cyl 5.7 L GAS
- Fleetwood | 1993 | Base, Brougham | 8 Cyl 5.7 L GAS
View related parts
Cadillac Ignition Module Part Number: 10482826
Product Specifications
- Other Name: Module Assembly, Distributor Ignition Control; Ignition Control Module; Module, Distributor (Also Knock Sensor)
Fits the following Cadillac Models:
- Allante | 1987-1990 | Base, Value Leader | 8 Cyl 4.1 L GAS, 8 Cyl 4.5 L GAS

Cadillac Ignition Control Module

Choose OEM Ignition Control Module, you're making the optimal decision for superior quality and perfect performance. You can feel confident because each component goes through stringent quality checks. Every part is carefully built to comply with Cadillac's factory specifications. You'll enjoy a smooth, worry-free installation that fits just right. At ChevyPartsGiant.com, you'll find it easy to get top-quality OEM Cadillac Ignition Control Module. You can shop at highly competitive prices and protect your budget. All our genuine Cadillac parts include a dependable manufacturer's warranty. You'll also appreciate our straightforward return policy and swift delivery services for extra convenience.

Cadillac Ignition Control Module Parts and Q&A

Ignition Module
19178832
Q: How to replace the ignition control module for Bank 1 on Cadillac DeVille?
A:
Begin Bank 1 Ignition Control Module replacement by first unbolting and removing the engine sight shield retaining bolts and engine sight shield. First detach the electrical connector which powers up the ignition control module. To perform the replacement you must start by disconnecting the AIR system vacuum hoses (labeling their original positions first) and remove the AIR pipe to exhaust manifold bolts. You must also disconnect the AIR vent solenoid electrical connector when removing the AIR assembly. Following the removal sequence remove the ignition assembly retaining bolts before carefully taking out the ignition assembly. First remove all ignition control module retaining screws before removing the module itself. Start by installing the ignition control module followed by tightening its retaining screws to 0.8 N.m (7 lb in). Place the ignition assembly insulation and grounding spring correctly then install the ignition assembly with retaining bolts tightened to 9 N.m (80 lb in). During installation of an engine with AIR features first add the AIR assembly before attaching the AIR bracket using proper torque settings for the bracket's bolts. Install the AIR vacuum hoses and the AIR pipe to exhaust manifold bolts and the AIR vent solenoid electrical connector when present. After lastly completing installation of the engine sight shield equipment tighten its retaining bolts up to 8 N.m (70 lb. in.) while also reconnecting the ignition assembly electrical connector.
Control Module
10482803
Q: How to replace the ignition coil and Ignition Control Module (HVS) on Cadillac Escalade?
A:
To replace the Ignition Coil and Ignition Control Module (HVS), you need to remove the air cleaner assembly and nut then disconnecting the electrical connectors. Next, remove the Ignition Coil wire from the Distributor and remove the studs that hold the bracket and Ignition Coil on the Intake Manifold. Next, you will have to remove the bracket and Ignition Coil, drill and punch out the two rivets that are holding the Ignition Coil to the bracket, and then take the Ignition Coil away from the bracket. For installation, mount the Ignition Coil into the bracket with the two screws included in the replacement Ignition Coil kit. Replace the Ignition Coil and bracket onto Intake Manifold using studs, fastening them with 11 n.m (8 lb ft). Reconnect the wire from Ignition Coil, make sure, it does not touch any part such as dip stick in order to avoid grounding or shorting after passing time. Lastly, reconnect the electric connectors and replace the air cleaner assembly and nut.