How to replace the wheel axle shaft on Cadillac Seville?

The first step to replace a wheel drive shaft requires vehicle support while lifting it up then removing all tire and wheel components. When the vehicle uses road sensing suspension technology it requires users to disconnect the level sensor link which attaches to the ball stud located on the lower Control Arm. Disconnection of the outer Tie Rod End from the Steering Knuckle happens without touching the Tie Rod End jam nut. A drift or punch should be inserted through the brake rotor in front of the brake caliper to stop the Wheel Hub and bearing from rotating. A new Spindle Nut is needed whenever you remove the wheel drive shaft Spindle Nut because it should not be reutilized. Separate the stabilizer shaft link and disconnect the electrical connector from the Wheel Speed Sensor while placing the wiring harness in a safe position that avoids the Ball Joint. Use the Wheel Hub remover (J 42129) to fit the Wheel Hub and fasten it using wheel nuts until the wheel drive shaft becomes completely detached while continuously supporting the shaft. The Wheel Hub remover (J 42129) should be used to separate the wheel drive shaft from the Wheel Hub and bearing before assembling a combination of slide hammer (J2619-O1) with Axle Shaft remover extension (J 29794) along with Axle Shaft puller (J 33008-A) to extract the wheel drive shaft from the transaxle and remove it from the vehicle. To install the wheel drive shaft, position it into the transaxle and check its alignment through inner tripot housing outward pull. First insert the wheel drive shaft into the hub with bearing before linking the Ball Joint to the Steering Knuckle followed by restoring the Wheel Speed Sensor electrical connection. The link of the stabilizer shaft must be installed before using a drift or punch tool to stop the hub and bearing from rotating against the caliper. Fasten the new wheel drive shaft Spindle Nut by torquing it to 160 nm (118 lb ft). Complete the process by connecting the outer Tie Rod End to the Steering Knuckle then reattaching the level sensor link (on road sensing suspension vehicles) after installing the tire and wheel assembly and lowering the vehicle.

OEM Cadillac Seville Axle Shaft

Car Axle Shaft

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

15 Axle Shafts found

View related parts
Cadillac Seville Axle Shaft Assembly, Front Passenger Side Part Number: 26078539
$35.71 MSRP: $597.64
You Save: $561.93 (95%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Kit, Front Wheel Drive; CV Axle Assembly; Axle Shaft; CV Axle; Axle Assembly; Shaft Kit, Front Wheel Drive Axle
- Position: Front Passenger Side
- Replaces: 26017179
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1989-1990 Cadillac Seville | Base, STS | 8 Cyl 4.5 L GAS
View related parts
Cadillac Seville Axle Shaft, Passenger Side Part Number: 7848444
$163.74 MSRP: $305.53
You Save: $141.79 (47%)
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly, Damper & (Painted); Shaft; Shaft, Front Wheel Drive Axle
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1986-1987 Cadillac Seville | Base, Elegante | 8 Cyl 4.1 L GAS
View related parts
Cadillac Seville Axle Shaft, Driver Side Part Number: 7846169
$50.66 MSRP: $90.46
You Save: $39.80 (44%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft, Front Wheel Drive; Axle Shafts; Shaft; Shaft, Front Wheel Drive Axle
- Position: Driver Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1986-1991 Cadillac Seville | Base, Elegante, STS | 8 Cyl 4.1 L GAS, 8 Cyl 4.5 L GAS, 8 Cyl 4.9 L GAS
View related parts
Cadillac Seville Axle Assembly, Front Part Number: 26078547
Product Specifications
- Other Name: Shaft Kit, Front Wheel Drive; Axle Shaft; Shaft Kit, Front Wheel Drive Axle
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1988 Cadillac Seville | Base, STS | 8 Cyl 4.5 L GAS
View related parts
Cadillac Seville Axle Assembly, Front Part Number: 26075603
Product Specifications
- Other Name: Shaft Kit, Front Wheel Drive; CV Axle Assembly; Axle Shaft; CV Axle; Axle
- Position: Front
- Replaced by: 20984613
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2004 Cadillac Seville | SLS, STS | 8 Cyl 4.6 L GAS
View related parts
Cadillac Seville Axle Shaft Assembly, Driver Side Part Number: 26009539
Product Specifications
- Other Name: Half Shift; Axle Shaft; Axle Assembly
- Position: Driver Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1988 Cadillac Seville | Base, STS | 8 Cyl 4.5 L GAS
View related parts
Cadillac Seville Axle Shaft Assembly, Driver Side Part Number: 26009538
Product Specifications
- Other Name: Halfshaft; Axle Shaft; Axle Assembly
- Position: Driver Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1988 Cadillac Seville | Base, STS | 8 Cyl 4.5 L GAS
View related parts
Cadillac Seville Axle Shaft, Front Driver Side Part Number: 26000329
Product Specifications
- Other Name: Shaft Kit-Front Wheel Drive; Axle Shaft Assembly; Axle Assembly; Shaft Assembly; Shaft Kit, Front Wheel Drive Axle; Axle Kit, Front Wheel Drive Axle
- Position: Front Driver Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1986-1987 Cadillac Seville | Base, Elegante | 8 Cyl 4.1 L GAS
View related parts
Cadillac Seville Axle Shaft Assembly, Front Part Number: 26078585
Product Specifications
- Other Name: Shaft Kit, Front Wheel Drive; CV Axle Assembly; Axle Shaft; CV Axle; Axle Assembly; Axle; Shaft Kit, Front Wheel Drive Axle
- Position: Front
- Replaces: 26027053, 26021720, 26035210
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1992-1993 Cadillac Seville | Base, STS | 8 Cyl 4.9 L GAS
View related parts
Cadillac Seville Axle Shaft Assembly, Front Passenger Side Part Number: 26078583
Product Specifications
- Other Name: Shaft Kit, Front Wheel Drive; CV Axle Assembly; Axle Shaft; CV Axle; Axle Assembly; Shaft Kit, Front Wheel Drive Axle
- Position: Front Passenger Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1991 Cadillac Seville | Base, STS | 8 Cyl 4.9 L GAS
View related parts
Cadillac Seville Axle Shaft Assembly, Front Driver Side Part Number: 26078505
Product Specifications
- Other Name: Shaft Kit, Front Wheel Drive; CV Axle Assembly; Axle Shaft; CV Axle; Axle Assembly; Shaft Kit, Front Wheel Drive Axle
- Position: Front Driver Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1989-1991 Cadillac Seville | Base, STS | 8 Cyl 4.5 L GAS, 8 Cyl 4.9 L GAS
View related parts
Cadillac Seville Axle Shaft Assembly, Front Part Number: 26078251
Product Specifications
- Other Name: Shaft Kit, Front Wheel Drive; CV Axle Assembly; Axle Shaft; CV Axle; Axle Assembly; Axle; Shaft Kit, Front Wheel Drive Axle
- Position: Front
- Replaces: 26021721, 26027054
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1992-1993 Cadillac Seville | Base, STS | 8 Cyl 4.9 L GAS
View related parts
Cadillac Seville Axle Shaft Assembly, Front Part Number: 26075423
Product Specifications
- Other Name: Shaft Kit, Front Wheel Drive; Axle Shaft; Axle Assembly; Axle; Shaft Kit, Front Wheel Drive Axle
- Position: Front
- Replaces: 26030759
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1993-1997 Cadillac Seville | SLS, STS | 8 Cyl 4.6 L GAS
View related parts
Cadillac Seville Axle Assembly, Front Part Number: 26063201
Product Specifications
- Other Name: Shaft Kit, Front Wheel Drive; CV Axle Assembly; Axle Shaft; CV Axle; Shaft Kit, Front Wheel Drive Axle
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1998-1999 Cadillac Seville | SLS, STS | 8 Cyl 4.6 L GAS
View related parts
Cadillac Seville Axle Shaft, Front Passenger Side Part Number: 26006856
Product Specifications
- Other Name: Shaft, Front Wheel Drive Axle; Shaft
- Position: Front Passenger Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1988-1991 Cadillac Seville | Base, STS | 8 Cyl 4.5 L GAS, 8 Cyl 4.9 L GAS

Cadillac Seville Axle Shaft

Want to cut long-term maintenance and repair costs? Choose OEM Axle Shaft. Those parts deliver top durability you can trust. On our site, you'll find a huge catalog of genuine Cadillac Seville parts. Prices are unbeatable, so you can keep more in your pocket. Every OEM Cadillac Seville Axle Shaft includes a manufacturer's warranty. You can also get an easy return policy that keeps buying risk free. Fast delivery, get your car on the road quickly. It's simple to search, compare, and order. Stop guessing about quality or fit. Order today and save with parts that last.

Cadillac Seville Axle Shaft is as important as any part when it comes to the overall efficiency and security of Cadillac automobiles. Its role is to transfer the torque from the differential to the drive wheels and also enable wheels to rotate independently; this aspect is very crucial concerning the Cadillac Seville's ability to turn corners tracting against the side force. Designed for Seville cars made from 1975 to 2004, the Axle Shaft is available in the solid axle and halfshaft varieties to accommodate car's suspension type. To recap, Cadillac Seville Axle Shaft is designed for accommodating the vehicle's weight through its solid axles that also houses the differential; the half shafts on the other hand transmits the power and contribute to it but does not bear the weight of the vehicle. This has not only the effect that the axle ratio can be realized in the optimal way, but also that the stability of the vehicle can be guaranteed through a precisely dosed power input. The Cadillac Seville Axle Shaft is built with this into consideration, meaning that there are parts that are built specifically in a way that will avoid things such as wearing of CV joints or the axle seals that in most cases cause the degradation of performance. Its solidity and design solutions that imply the use of the latest technologies in car manufacturing making the car stand out among similar ones in the automotive industry. Finally, the Cadillac Seville Axle Shaft is the example of Cadillac's adhesion to quality and power, guaranteeing that every Seville model will provide the optimal performance with perfect stability and durability.

Cadillac Seville Axle Shaft Parts and Q&A

Axle Assembly, Front
26075603
Q: How to replace the wheel axle shaft on Cadillac Seville?
A:
The first step to replace a wheel drive shaft requires vehicle support while lifting it up then removing all tire and wheel components. When the vehicle uses road sensing suspension technology it requires users to disconnect the level sensor link which attaches to the ball stud located on the lower Control Arm. Disconnection of the outer Tie Rod End from the Steering Knuckle happens without touching the Tie Rod End jam nut. A drift or punch should be inserted through the brake rotor in front of the brake caliper to stop the Wheel Hub and bearing from rotating. A new Spindle Nut is needed whenever you remove the wheel drive shaft Spindle Nut because it should not be reutilized. Separate the stabilizer shaft link and disconnect the electrical connector from the Wheel Speed Sensor while placing the wiring harness in a safe position that avoids the Ball Joint. Use the Wheel Hub remover (J 42129) to fit the Wheel Hub and fasten it using wheel nuts until the wheel drive shaft becomes completely detached while continuously supporting the shaft. The Wheel Hub remover (J 42129) should be used to separate the wheel drive shaft from the Wheel Hub and bearing before assembling a combination of slide hammer (J2619-O1) with Axle Shaft remover extension (J 29794) along with Axle Shaft puller (J 33008-A) to extract the wheel drive shaft from the transaxle and remove it from the vehicle. To install the wheel drive shaft, position it into the transaxle and check its alignment through inner tripot housing outward pull. First insert the wheel drive shaft into the hub with bearing before linking the Ball Joint to the Steering Knuckle followed by restoring the Wheel Speed Sensor electrical connection. The link of the stabilizer shaft must be installed before using a drift or punch tool to stop the hub and bearing from rotating against the caliper. Fasten the new wheel drive shaft Spindle Nut by torquing it to 160 nm (118 lb ft). Complete the process by connecting the outer Tie Rod End to the Steering Knuckle then reattaching the level sensor link (on road sensing suspension vehicles) after installing the tire and wheel assembly and lowering the vehicle.