How to replace the front Door Latch Assembly on Chevrolet Impala?

The process to replace a front Door Lock in an impala requires initial removal of front door trim panel along with the water deflector. You must detach interior handle rods from inside handle before you remove the clip which holds those rods onto the door. Separate the outside handle rod-to-lock clip from the lock before unscrewing the lock with screws from the door. Start by pulling out the lock from its position while maintaining the connection of inside handle rods followed by disconnecting electrical connectors. Start by placing the inside handle rods onto the lock before aligning the lock through the opening of the inner bar then restore electrical linkage points. Use the following correct fastener tightening order for lock screws when installing: start with top then bottom and middle followed by tightening the screws to 10 n.m (89 lb in). The installation requires a new outside handle rod-to-lock clip that should be mounted onto the lock lever followed by positioning the outside Door Handle rod into the clip to remove any play before installing the clip cover over the threaded rod. After reinserting the inside handle rods into the handle you should attach the water deflector and trim panel and secure the clip back onto the inside handle rods. Conduct a final examination of the Door Lock system for adequate functioning.

How to replace the rear Door Latch Assembly on Chevrolet Impala?

A replacement for the impala rear Door Lock starts with removing the rear door trim panel along with the water deflector. First detach the outside handle rod from the lock and pull out the inside handle rods from the rear Door Handle followed by clip removal of the inside handle rods. You should begin by removing the rear Door Lock screws before extracting the lock with its attached inside handle rods. Use a screwdriver to detach all electrical connectors before taking out the inside handle rods from the lock assembly. Begin by installing the inside handle rods onto the lock followed by putting the lock through the access hole in the rear door inner panel then connect the electrical connectors. Put all rear Door Lock screws into the installation slots in this order from top to bottom to middle and torque them to 10 n.m (89 lb in). You should install a new outside handle rod-to-lock clip on the lock lever which requires positioning the outside Door Handle rod into the clip before securing the clip cover on top of the threaded rods. To complete the installation put the clip on the inside handle rods before attaching the rods to their designated handle position then reinstall the water deflector followed by the trim panel. Perform a lock system operation check as the final step.

OEM Chevrolet Impala Door Latch Assembly

Door Latch

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

38 Door Latch Assemblys found

View related parts
Chevrolet Impala Lock Assembly, Passenger Side Part Number: 15111446
$121.44 MSRP: $175.27
You Save: $53.83 (31%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Latch, Door Lock; Door Lock Actuator Motor; Door Lock Actuator; Lock; Door Lock
- Position: Passenger Side
- Replaces: 16631792, 15066137
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1994-1996 Chevrolet Impala | SS | 8 Cyl 5.7 L GAS
View related parts
Chevrolet Impala Lock Assembly, Front Driver Side Part Number: 15111447
$176.41 MSRP: $250.28
You Save: $73.87 (30%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Lock, Front Side Door; Door Lock Actuator Motor; Door Lock Actuator; Door Lock; Lock; Lock, Door Lock
- Position: Front Driver Side
- Replaces: 15763384, 15066138, 16631793
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1994-1996 Chevrolet Impala | SS | 8 Cyl 5.7 L GAS
View related parts
Chevrolet Impala Lock Actuator, Rear Passenger Side Part Number: 13528274
$114.45 MSRP: $168.10
You Save: $53.65 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Latch Assembly-Rear Side Door; Door Lock Actuator Motor; Door Latch Assembly; Door Lock; Latch Assembly; Lock Assembly; Lock; Latch
- Position: Rear Passenger Side
- Replaced by: 13546591
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2015-2020 Chevrolet Impala | LS, LT, LTZ, Premier | 4 Cyl 2.5 L FLEX, 4 Cyl 2.5 L GAS, 6 Cyl 3.6 L BI-FUEL, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS
View related parts
Chevrolet Impala Lock Part Number: 16630045
$32.01 MSRP: $79.62
You Save: $47.61 (60%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Latch Assembly-Rear Door Mini-Wedge; Door Latch Assembly; Door Lock; Lock, Rear Side Door
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1994-1996 Chevrolet Impala | SS | 8 Cyl 5.7 L GAS
View related parts
Chevrolet Impala Lock Assembly, Rear Driver Side Part Number: 16639125
Product Specifications
- Other Name: Latch, Rear Side Door; Door Latch Assembly; Door Lock; Lock
- Position: Rear Driver Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2005 Chevrolet Impala | Base, LS, LS Sport, SS | 6 Cyl 3.4 L GAS, 6 Cyl 3.8 L GAS
View related parts
Chevrolet Impala Lock Assembly, Front Part Number: 16608235
Product Specifications
- Other Name: Lock, Front Side Door; Door Lock Actuator Motor; Door Latch Assembly; Door Lock Actuator; Door Lock; Lock; Latch; Lock, Door Lock
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1984-1985 Chevrolet Impala | Base | 6 Cyl 3.8 L GAS, 6 Cyl 4.3 L GAS, 8 Cyl 5.0 L GAS, 8 Cyl 5.7 L DIESEL, 8 Cyl 5.7 L GAS
View related parts
Chevrolet Impala Lock Assembly, Front Driver Side Part Number: 10347027
Product Specifications
- Other Name: Lock, Front Side Door; Door Lock; Lock
- Position: Front Driver Side
- Replaces: 10303485, 10303215, 10313980, 16637911
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2005 Chevrolet Impala | Base, LS, LS Sport, SS | 6 Cyl 3.4 L GAS, 6 Cyl 3.8 L GAS
View related parts
Chevrolet Impala Lock, Rear Part Number: 10304039
$220.63 MSRP: $329.85
You Save: $109.22 (34%)
Product Specifications
- Other Name: Latch, Rear Compartment Lid Or Tail Gate Latch; Trunk Latch; Door Lock; Latch; Latch, Rear Compartment Lid Release Or Ajar
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2001-2005 Chevrolet Impala | Base, LS, LS Sport, SS | 6 Cyl 3.4 L GAS, 6 Cyl 3.8 L GAS
View related parts
Chevrolet Impala Lock, Passenger Side Part Number: 16630044
Product Specifications
- Other Name: Latch Assembly-Rear Door Mini-Wedge; Door Latch Assembly; Door Lock; Lock, Rear Side Door
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1994-1996 Chevrolet Impala | SS | 8 Cyl 5.7 L GAS
View related parts
Chevrolet Impala Lock, Rear Driver Side Part Number: 16630051
Product Specifications
- Other Name: Lock, Rear Side Door; Door Latch Assembly; Door Lock
- Position: Rear Driver Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1995-1996 Chevrolet Impala | SS | 8 Cyl 5.7 L GAS
View related parts
Chevrolet Impala Lock Actuator Part Number: 22100852
Product Specifications
- Other Name: Actuator, Door Electric And Vacuum Locks; Door Lock Actuator Motor; Door Lock Actuator; Lock Solenoid; Actuator
- Position: Front and Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1994-1996 Chevrolet Impala | SS | 8 Cyl 5.7 L GAS
View related parts
Chevrolet Impala Lock Actuator Part Number: 22062740
Product Specifications
- Other Name: Actuator, Door Electric And Vacuum Locks; Door Lock Actuator Motor; Door Lock Actuator; Power Actuator; Latch Actuator; Lock Solenoid; Lock; Actuator; Actuator, Door And End Gate Electrical
- Position: Front
- Replaces: 22020256, 22049686
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1984-1985 Chevrolet Impala | Base | 6 Cyl 3.8 L GAS, 6 Cyl 4.3 L GAS, 8 Cyl 5.0 L GAS, 8 Cyl 5.7 L DIESEL, 8 Cyl 5.7 L GAS
View related parts
Chevrolet Impala Lock, Passenger Side Part Number: 16608174
Product Specifications
- Other Name: Door Latch Assembly; Door Lock
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1984-1985 Chevrolet Impala | Base | 6 Cyl 3.8 L GAS, 6 Cyl 4.3 L GAS, 8 Cyl 5.0 L GAS, 8 Cyl 5.7 L DIESEL, 8 Cyl 5.7 L GAS
View related parts
Chevrolet Impala Lock, Rear Driver Side Part Number: 16608175
Product Specifications
- Other Name: Lock, Rear Side Door; Door Latch Assembly; Door Lock
- Position: Rear Driver Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1984-1985 Chevrolet Impala | Base | 6 Cyl 3.8 L GAS, 6 Cyl 4.3 L GAS, 8 Cyl 5.0 L GAS, 8 Cyl 5.7 L DIESEL, 8 Cyl 5.7 L GAS
View related parts
Chevrolet Impala Lock, Passenger Side Part Number: 16608164
Product Specifications
- Other Name: Lock Assembly-Front Door Right-Hand; Door Lock; Lock, Front Side Door
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1984-1985 Chevrolet Impala | Base | 6 Cyl 3.8 L GAS, 6 Cyl 4.3 L GAS, 8 Cyl 5.0 L GAS, 8 Cyl 5.7 L DIESEL, 8 Cyl 5.7 L GAS
View related parts
Chevrolet Impala Lock Assembly, Rear Passenger Side Part Number: 16639124
Product Specifications
- Other Name: Latch, Rear Side Door; Door Latch Assembly; Door Lock; Lock
- Position: Rear Passenger Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2005 Chevrolet Impala | Base, LS, LS Sport, SS | 6 Cyl 3.4 L GAS, 6 Cyl 3.8 L GAS
View related parts
Chevrolet Impala Lock, Front Driver Side Part Number: 16608165
Product Specifications
- Other Name: Lock, Front Side Door; Door Lock
- Position: Front Driver Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1984-1985 Chevrolet Impala | Base | 6 Cyl 3.8 L GAS, 6 Cyl 4.3 L GAS, 8 Cyl 5.0 L GAS, 8 Cyl 5.7 L DIESEL, 8 Cyl 5.7 L GAS
View related parts
Chevrolet Impala Lock Assembly, Passenger Side Part Number: 16608234
Product Specifications
- Other Name: Lock, Door Lock; Door Lock Actuator Motor; Door Latch Assembly; Door Lock Actuator; Lock; Latch; Lock, Front Side Door; Door Lock
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1984-1985 Chevrolet Impala | Base | 6 Cyl 3.8 L GAS, 6 Cyl 4.3 L GAS, 8 Cyl 5.0 L GAS, 8 Cyl 5.7 L DIESEL, 8 Cyl 5.7 L GAS
View related parts
Chevrolet Impala Lock Assembly Part Number: 88981042
Product Specifications
- Other Name: Lock, Front Side Door; Door Lock; Lock
- Position: Front
- Replaces: 16639132
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2005 Chevrolet Impala | Base, LS, LS Sport, SS | 6 Cyl 3.4 L GAS, 6 Cyl 3.8 L GAS
View related parts
Chevrolet Impala Lock Assembly, Front Passenger Side Part Number: 10347026
Product Specifications
- Other Name: Lock, Front Side Door; Door Lock; Lock
- Position: Front Passenger Side
- Replaces: 10331568
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2004-2005 Chevrolet Impala | Base, LS, SS | 6 Cyl 3.4 L GAS, 6 Cyl 3.8 L GAS

| Page 1 of 2 |Next >

1-20 of 38 Results

Chevrolet Impala Door Latch Assembly

Want to cut long-term maintenance and repair costs? Choose OEM Door Latch Assembly. Those parts deliver top durability you can trust. On our site, you'll find a huge catalog of genuine Chevrolet Impala parts. Prices are unbeatable, so you can keep more in your pocket. Every OEM Chevrolet Impala Door Latch Assembly includes a manufacturer's warranty. You can also get an easy return policy that keeps buying risk free. Fast delivery, get your car on the road quickly. It's simple to search, compare, and order. Stop guessing about quality or fit. Order today and save with parts that last.

The Door Latch Assembly in Chevrolet Impala means a lock that keeps the doors of the vehicle closed in order to keep unwanted persons from getting into the car. This assembly may incorporate several locking systems which are automatic or manually operated and the doors can be locked individually or in batches from a central point. Currently, there are different styles off Door Latch Assembly that have been used in Chevrolet Impala over the years with the aim of ensuring that the car doors are well latched and easily opened. Some of the reasons why people may require replacement of these assemblies are because they may be of a sturdy nature but may sometimes jam or develop such problems as defective outer door handles, sticking mechanisms, or sometimes may be difficult to push the button for the lock/ unlock operation. It is important that people should perform the Chevrolet Impala Door Latch Assembly service frequently to guarantee the safety and efficiency of the car.

Chevrolet Impala Door Latch Assembly Parts and Q&A

Lock Assembly, Front Driver Side
10347027
Q: How to replace the front Door Latch Assembly on Chevrolet Impala?
A:
The process to replace a front Door Lock in an impala requires initial removal of front door trim panel along with the water deflector. You must detach interior handle rods from inside handle before you remove the clip which holds those rods onto the door. Separate the outside handle rod-to-lock clip from the lock before unscrewing the lock with screws from the door. Start by pulling out the lock from its position while maintaining the connection of inside handle rods followed by disconnecting electrical connectors. Start by placing the inside handle rods onto the lock before aligning the lock through the opening of the inner bar then restore electrical linkage points. Use the following correct fastener tightening order for lock screws when installing: start with top then bottom and middle followed by tightening the screws to 10 n.m (89 lb in). The installation requires a new outside handle rod-to-lock clip that should be mounted onto the lock lever followed by positioning the outside Door Handle rod into the clip to remove any play before installing the clip cover over the threaded rod. After reinserting the inside handle rods into the handle you should attach the water deflector and trim panel and secure the clip back onto the inside handle rods. Conduct a final examination of the Door Lock system for adequate functioning.
Lock Assembly
88981043
Q: How to replace the rear Door Latch Assembly on Chevrolet Impala?
A:
A replacement for the impala rear Door Lock starts with removing the rear door trim panel along with the water deflector. First detach the outside handle rod from the lock and pull out the inside handle rods from the rear Door Handle followed by clip removal of the inside handle rods. You should begin by removing the rear Door Lock screws before extracting the lock with its attached inside handle rods. Use a screwdriver to detach all electrical connectors before taking out the inside handle rods from the lock assembly. Begin by installing the inside handle rods onto the lock followed by putting the lock through the access hole in the rear door inner panel then connect the electrical connectors. Put all rear Door Lock screws into the installation slots in this order from top to bottom to middle and torque them to 10 n.m (89 lb in). You should install a new outside handle rod-to-lock clip on the lock lever which requires positioning the outside Door Handle rod into the clip before securing the clip cover on top of the threaded rods. To complete the installation put the clip on the inside handle rods before attaching the rods to their designated handle position then reinstall the water deflector followed by the trim panel. Perform a lock system operation check as the final step.