How to service and repair the fan shroud on Chevrolet Impala?

The Fan Shroud servicing requires disconnecting the battery ground (negative) cable before other steps. The cooling system requires partial draining before the swinging movement of engine struts can start by loosening their bolts to prevent rubber bushing shearing. First detach the engine strut brace bolts from the upper tie bar before swinging the struts as well as braces toward the rear. Secondly disconnect the front fender upper diagonal brace. To acquire access to the throttle body air inlet users should disconnect it and adjust the air cleaner assembly before detaching the radiator inlet hose from the radiator. Remove the cooling Fan Shroud by first releasing the retainers and then untightening all shroud bolts. The transmission oil cooler lines need to be separated from their retainers at the cooling Fan Shroud bottom while using pliers to detach the cooling Fan Shroud clip from the upper radiator edge. First disconnect the cooling Fan Shroud electrical connector followed by repositioning the cooling Fan Shroud to access it for removing the cooling Fan Shroud. The process for installation requires plugging in the cooling Fan Shroud electrical connector followed by attaching the cooling Fan Shroud to its place. Pull the cooling Fan Shroud clip toward the top of the radiator surface until you can see full attachment. Secure the transmission oil cooler lines to their retainers situated at the bottom of the cooling Fan Shroud before screwing and tightening the cooling Fan Shroud bolts to 10 nm (89 inch lbs.). Reinstall the cool Fan Shroud retainers after you connect the radiator inlet hose to its position on the radiator and install the air cleaner assembly properly by threading the throttle body air inlet duct first. Screw the front fender upper diagonal brace into place before rotating its struts forward to their correct position where you will tighten the engine strut brace bolts onto the upper tie bar. Fill the cooling system while performing ground connection to the battery and verify system functionality.

OEM Chevrolet Impala Fan Shroud

Radiator Fan Shroud

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

15 Fan Shrouds found

View related parts
Chevrolet Impala Fan Shroud Part Number: 89018694
$249.96 MSRP: $322.31
You Save: $72.35 (23%)
ADD TO CART
Product Specifications
- Other Name: Shroud Kit, Engine Electrical Coolant Fan; Dual Radiator and Condenser Fan Assembly; Cooling Fan Assembly; Shroud; Shroud Kit, Radiator Fan Shroud
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2009-2011 Chevrolet Impala | LS, LT, LTZ | 6 Cyl 3.5 L FLEX, 6 Cyl 3.5 L GAS, 6 Cyl 3.9 L FLEX
View related parts
Chevrolet Impala Fan & Motor Part Number: 19130418
$318.47 MSRP: $584.75
You Save: $266.28 (46%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Shroud Assembly, Engine Coolant Fan; Dual Radiator and Condenser Fan Assembly; Cooling Fan Assembly; Fan Assembly; Shroud, Engine Air Cooling(Electrical); Shroud, Radiator Fan Shroud
- Replaces: 10435233, 89022511
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2003 Chevrolet Impala | Base, LS, LS Sport, Police | 6 Cyl 3.4 L GAS, 6 Cyl 3.8 L GAS
View related parts
Chevrolet Impala Fan Shroud Part Number: 89018697
$159.42 MSRP: $304.10
You Save: $144.68 (48%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shroud Kit, Engine Electrical Coolant Fan; Dual Radiator and Condenser Fan Assembly; Cooling Fan Assembly; Shroud; Shroud Kit, Radiator Fan Shroud
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2006-2013 Chevrolet Impala | 50th Anniversary Edition, LS, LT, LTZ, Police, SS | 6 Cyl 3.5 L FLEX, 6 Cyl 3.5 L GAS, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 6 Cyl 3.9 L FLEX, 6 Cyl 3.9 L GAS, 8 Cyl 5.3 L GAS
View related parts
Chevrolet Impala Fan Shroud Part Number: 23131503
$297.71 MSRP: $445.01
You Save: $147.30 (34%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shroud, Radiator Fan Shroud; Dual Radiator and Condenser Fan Assembly; Cooling Fan Assembly
- Replaces: 20979495
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2014-2019 Chevrolet Impala | LS, LT, LTZ | 4 Cyl 2.5 L FLEX, 4 Cyl 2.5 L GAS
View related parts
Chevrolet Impala Fan Shroud Part Number: 22747159
$289.82 MSRP: $433.21
You Save: $143.39 (34%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shroud, Radiator Fan Shroud; Dual Radiator and Condenser Fan Assembly; Cooling Fan Assembly
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2014-2020 Chevrolet Impala | LS, LT, LTZ, Premier | 6 Cyl 3.6 L BI-FUEL, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS
View related parts
Chevrolet Impala Fan Shroud Part Number: 20970655
$289.71 MSRP: $433.05
You Save: $143.34 (34%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shroud, Radiator Fan Shroud; Dual Radiator and Condenser Fan Assembly; Cooling Fan Assembly; Cooling Shroud
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2014-2020 Chevrolet Impala | Eco, LS, LT, LTZ, Premier | 4 Cyl 2.4 L MILD HYBRID EV-GAS (MHEV), 6 Cyl 3.6 L BI-FUEL, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS
View related parts
Chevrolet Impala Fan Shroud Part Number: 89019107
Product Specifications
- Other Name: Shroud Assembly, Engine Coolant Fan; Dual Radiator and Condenser Fan Assembly; Cooling Fan Assembly; Shroud; Shroud Kit, Radiator Fan Shroud
- Replaces: 88987274, 89018446
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2004-2005 Chevrolet Impala | Base, LS, Police, SS | 6 Cyl 3.4 L GAS, 6 Cyl 3.8 L GAS
View related parts
Chevrolet Impala Lower Shroud Part Number: 10260565
Product Specifications
- Other Name: Shroud, Radiator Fan Shroud; Fan Shroud
- Position: Lower
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1994-1996 Chevrolet Impala | SS | 8 Cyl 5.7 L GAS
View related parts
Chevrolet Impala Fan Shroud Part Number: 89018447
Product Specifications
- Other Name: Shroud, Radiator Fan Shroud; Shroud
- Replaces: 88956883
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2004-2005 Chevrolet Impala | Base, LS, Police, SS | 6 Cyl 3.4 L GAS, 6 Cyl 3.8 L GAS
View related parts
Chevrolet Impala Lower Shroud Part Number: 14010526
Product Specifications
- Other Name: Shroud; Fan Shroud; Shroud, Radiator Fan Shroud
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1984-1985 Chevrolet Impala | Base | 8 Cyl 5.0 L GAS, 8 Cyl 5.7 L DIESEL, 8 Cyl 5.7 L GAS
View related parts
Chevrolet Impala Lower Shroud Part Number: 14010508
Product Specifications
- Other Name: Shroud, Radiator Fan Shroud; Shroud; Fan Shroud
- Position: Lower
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1984 Chevrolet Impala | Base | 6 Cyl 3.8 L GAS
View related parts
Chevrolet Impala Shroud Part Number: 10065719
Product Specifications
- Other Name: Shroud, Radiator Fan Shroud; Fan Shroud
- Position: Upper
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1984-1985 Chevrolet Impala | Base | 8 Cyl 5.0 L GAS, 8 Cyl 5.7 L DIESEL, 8 Cyl 5.7 L GAS
View related parts
Chevrolet Impala Shroud Part Number: 10065718
Product Specifications
- Other Name: Fan Shroud; Shroud, Radiator Fan Shroud
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1984 Chevrolet Impala | Base | 6 Cyl 3.8 L GAS
View related parts
Chevrolet Impala Fan & Motor Part Number: 19130419
Product Specifications
- Other Name: Shroud Assembly, Engine Coolant Fan; Dual Radiator and Condenser Fan Assembly; Cooling Fan Assembly; Fan Assembly; Shroud, Engine Air Cooling(Electrical); Shroud, Radiator Fan Shroud
- Replaces: 89022512, 10419167
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2003 Chevrolet Impala | Base, LS, LS Sport, Police | 6 Cyl 3.4 L GAS, 6 Cyl 3.8 L GAS
View related parts
Chevrolet Impala Upper Shroud Part Number: 10281083
Product Specifications
- Other Name: Shroud, Radiator Fan Shroud; Fan Shroud
- Position: Upper
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1994-1996 Chevrolet Impala | SS | 8 Cyl 5.7 L GAS

Chevrolet Impala Fan Shroud

Want to cut long-term maintenance and repair costs? Choose OEM Fan Shroud. Those parts deliver top durability you can trust. On our site, you'll find a huge catalog of genuine Chevrolet Impala parts. Prices are unbeatable, so you can keep more in your pocket. Every OEM Chevrolet Impala Fan Shroud includes a manufacturer's warranty. You can also get an easy return policy that keeps buying risk free. Fast delivery, get your car on the road quickly. It's simple to search, compare, and order. Stop guessing about quality or fit. Order today and save with parts that last.

A Chevrolet Impala Fan Shroud is an essential part that helps a lot in increasing the effectiveness together with the performance of the Impala's cooling system. The Fan Shroud wraps around the cooling fan blades for improving the airflow specifically towards the engine; the engine has to be at an optimal working temperature for it to properly perform and then to run for a long time. This component also shields the fan from dust thus promoting the protection of the cooling system from wearing out. Years passed and designs of the Chevrolet Impala models have different styles of Fan Shroud not only to address the cooling needs but in the process serves the primary purpose of enhancing the cooling factor. Taking the Chevrolet Impala Fan Shroud into consideration one can point out the fact that the automotive market has highly benefited from the advancement in the field of automotive engineering. It can be used on different generations of the Chevrolet Impala, which optimizes it between race car drivers and regular people. Thus, the Fan Shroud can be regarded not only as a purely functional part of the car: it ensures vehicle safety by avoiding overheating and subsequent damage to the engine. Being one of Chevrolet Impala's essential parts in its engineering, the Chevrolet Impala Fan Shroud reflects the brand's synonymous with reliability and performance that will help the famous full-sized sedan to maintain the power and comfort needed.

Chevrolet Impala Fan Shroud Parts Questions & Experts Answers

Fan & Motor
19130418
Q: How to service and repair the fan shroud on Chevrolet Impala?
A:
The Fan Shroud servicing requires disconnecting the battery ground (negative) cable before other steps. The cooling system requires partial draining before the swinging movement of engine struts can start by loosening their bolts to prevent rubber bushing shearing. First detach the engine strut brace bolts from the upper tie bar before swinging the struts as well as braces toward the rear. Secondly disconnect the front fender upper diagonal brace. To acquire access to the throttle body air inlet users should disconnect it and adjust the air cleaner assembly before detaching the radiator inlet hose from the radiator. Remove the cooling Fan Shroud by first releasing the retainers and then untightening all shroud bolts. The transmission oil cooler lines need to be separated from their retainers at the cooling Fan Shroud bottom while using pliers to detach the cooling Fan Shroud clip from the upper radiator edge. First disconnect the cooling Fan Shroud electrical connector followed by repositioning the cooling Fan Shroud to access it for removing the cooling Fan Shroud. The process for installation requires plugging in the cooling Fan Shroud electrical connector followed by attaching the cooling Fan Shroud to its place. Pull the cooling Fan Shroud clip toward the top of the radiator surface until you can see full attachment. Secure the transmission oil cooler lines to their retainers situated at the bottom of the cooling Fan Shroud before screwing and tightening the cooling Fan Shroud bolts to 10 nm (89 inch lbs.). Reinstall the cool Fan Shroud retainers after you connect the radiator inlet hose to its position on the radiator and install the air cleaner assembly properly by threading the throttle body air inlet duct first. Screw the front fender upper diagonal brace into place before rotating its struts forward to their correct position where you will tighten the engine strut brace bolts onto the upper tie bar. Fill the cooling system while performing ground connection to the battery and verify system functionality.