How to replace the connecting rod bearing on Chevrolet Impala?

To dismantle the connecting Rod Bearing one will need to collect the following tools: connecting rod bolt guide set (J 5239), torque angle meter (J 36660-A), cylinder bore ridge reamer (J 24270). Start by removing the Oil Pan, and Oil Pump off the Crankshaft oil deflector. Rotate the Crankshaft together with the Piston and rod assembly to be serviced to bottom dead center (BDC), of course making sure that match marks on the connecting rod and caps are used. Remove nuts of connecting rods, cap, and also lower connecting rods bearing with caution and also install thread protector to prevent Crankshaft journal damage. Replace the lower Piston, upper connecting Rod Bearing, then push the Piston and connecting rod up the cylinder to access the top of the Piston and bolt what's called the tope Piston before installing lower Piston, lower Piston, back bearing, upper Rod Bearing, new Piston browning up from bottom, and reverse all the steps. Clean off oil from the connecting rod bearings and Crankshaft journal, then check all components. For installation, oil the top connecting Rod Bearing with new engine oil and use the j 5239 in lowering the Piston and rod assembly to crank. Install the lower connecting Rod Bearing in the cap, oil it, and install the connecting rod cap and nuts with proper torque. It is also recommended to measure the connecting rod side clearance and install Crankshaft oil deflector, Oil Pump, and Oil Pan then lower the vehicle after installation. Put on new engine oil on the Piston, rings, cylinder bore, and bearing surfaces; using the Piston ring compressor (J 8037), compress the Piston rings and fit the Piston to its original bore. Follow similar ease with the installation of the connecting rod to make sure that any component is tightened and checked for any problem before reassembling the engine.

OEM Chevrolet Impala Rod Bearing

Engine Connecting Rod Bearing

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

9 Rod Bearings found

View related parts
Chevrolet Impala Connecting Rod Bearing
Part Number: 12657438
$12.23 MSRP: $19.16
You Save: $6.93 (37%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Bearing Kit, Connecting Rod; Bearing Set
- Replaced by: 12668645
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2014-2019 Chevrolet Impala | LS, LT, LTZ | 4 Cyl 2.5 L FLEX, 4 Cyl 2.5 L GAS
View related parts
Chevrolet Impala Bearing
Part Number: 89017573
$15.74 MSRP: $24.65
You Save: $8.91 (37%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Bearing Kit, Connecting Rod; Rod Bearing; Bearings; Bearing Kit, Engine Connecting Rod; Bearing, Engine Connecting Rod
- Replaces: 12493714, 12493712
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2006-2009 Chevrolet Impala | SS | 8 Cyl 5.3 L GAS
View related parts
Chevrolet Impala Connecting Rod Bearing
Part Number: 12643667
$10.84 MSRP: $16.99
You Save: $6.15 (37%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bearing Kit, Engine Connecting Rod; Rod Bearing; Bearing; Bearings
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2012-2020 Chevrolet Impala | LS, LT, LTZ, Police, Premier | 6 Cyl 3.6 L BI-FUEL, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS
View related parts
Chevrolet Impala Bearing Set, Green Line
Part Number: 12591093
$45.64 MSRP: $71.52
You Save: $25.88 (37%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Bearing Kit, Connecting Rod; Rod Bearing; Bearings; Bearing Kit, Engine Connecting Rod
- Replaces: 21018825
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2014 Chevrolet Impala | Eco | 4 Cyl 2.4 L MILD HYBRID EV-GAS (MHEV)
View related parts
Chevrolet Impala Connecting Rod Bearing
Part Number: 12480255
$0.38 MSRP: $0.59
You Save: $0.21 (36%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bearing Kit, Connecting Rod; Rod Bearing; Bearings; Bearing Kit, Engine Connecting Rod
- Replaces: 12518302
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2005 Chevrolet Impala | Base | 6 Cyl 3.4 L GAS
View related parts
Chevrolet Impala Rod Bearings
Part Number: 89017700
$15.78 MSRP: $24.72
You Save: $8.94 (37%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bearing Kit, Connecting Rod; Rod Bearing; Connecting Rod Bearing; Bearing Set; Bearings; Bearing Kit, Engine Connecting Rod; Bearing, Engine Connecting Rod
- Replaces: 12480819, 12537418, 89017565, 18005399
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2005, 1984 Chevrolet Impala | Base, LS, LS Sport, Police, SS | 6 Cyl 3.8 L GAS
View related parts
Chevrolet Impala Connecting Rod Bearing
Part Number: 12523924
$33.39 MSRP: $52.29
You Save: $18.90 (37%)
Ships in 1 Business Day
ADD TO CART
Product Specifications
- Other Name: Bearing Kit, Connecting Rod; Rod Bearing; Bearing; Bearings; Bearing Kit, Engine Connecting Rod
- Replaces: 12523927
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1994-1996 Chevrolet Impala | SS | 8 Cyl 5.7 L GAS
View related parts
Chevrolet Impala Bearings
Part Number: 89060553
$6.22 MSRP: $9.74
You Save: $3.52 (37%)
Product Specifications
- Other Name: Bearing Kit, Connecting Rod; Rod Bearing; Bearing Kit, Engine Connecting Rod
- Replaces: 12586085
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2006-2011 Chevrolet Impala | 50th Anniversary Edition, LS, LT, LTZ, Police | 6 Cyl 3.5 L FLEX, 6 Cyl 3.5 L GAS, 6 Cyl 3.9 L FLEX, 6 Cyl 3.9 L GAS
View related parts
Chevrolet Impala Bearings
Part Number: 18008494
Product Specifications
- Other Name: Bearing Kit, Engine Connecting Rod; Rod Bearing; Bearing, Engine Connecting Rod
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1984-1985 Chevrolet Impala | Base | 8 Cyl 5.7 L DIESEL

Chevrolet Impala Rod Bearing

Our website offers an extensive catalog of genuine Chevrolet Impala Rod Bearing at unbeatable prices. Every OEM Chevrolet Impala Rod Bearing comes with a manufacturer's warranty, an easy return policy, and rapid delivery service. Don't miss out on this great opportunity!

Chevrolet Impala Rod Bearing Parts Questions & Experts Answers

Rod Bearings
89017700
Q: How to replace the connecting rod bearing on Chevrolet Impala?
A: To dismantle the connecting Rod Bearing one will need to collect the following tools: connecting rod bolt guide set (J 5239), torque angle meter (J 36660-A), cylinder bore ridge reamer (J 24270). Start by removing the Oil Pan, and Oil Pump off the Crankshaft oil deflector. Rotate the Crankshaft together with the Piston and rod assembly to be serviced to bottom dead center (BDC), of course making sure that match marks on the connecting rod and caps are used. Remove nuts of connecting rods, cap, and also lower connecting rods bearing with caution and also install thread protector to prevent Crankshaft journal damage. Replace the lower Piston, upper connecting Rod Bearing, then push the Piston and connecting rod up the cylinder to access the top of the Piston and bolt what's called the tope Piston before installing lower Piston, lower Piston, back bearing, upper Rod Bearing, new Piston browning up from bottom, and reverse all the steps. Clean off oil from the connecting rod bearings and Crankshaft journal, then check all components. For installation, oil the top connecting Rod Bearing with new engine oil and use the j 5239 in lowering the Piston and rod assembly to crank. Install the lower connecting Rod Bearing in the cap, oil it, and install the connecting rod cap and nuts with proper torque. It is also recommended to measure the connecting rod side clearance and install Crankshaft oil deflector, Oil Pump, and Oil Pan then lower the vehicle after installation. Put on new engine oil on the Piston, rings, cylinder bore, and bearing surfaces; using the Piston ring compressor (J 8037), compress the Piston rings and fit the Piston to its original bore. Follow similar ease with the installation of the connecting rod to make sure that any component is tightened and checked for any problem before reassembling the engine.