How to replace the front Fender Splash Shield on Chevrolet Monte Carlo?

The procedure for front fender splash shield replacement begins by drilling out plastic rivets from the front fascia extension corner to the front fender splash shield when the vehicle has this configuration. You should start by removing the front fender splash shield screws from the front bumper fascia area and the nut from the stud located near the rear of the front fender splash shield and the bolt securing the front tab on the front fender splash shield at the lower engine compartment side rail. Start by drilling the plastic rivet connecting the front rocker panel to the front fender splash shield whenever present followed by the removal of front fender splash shield screws. Fix the splash shield along the fender while reaching over the stud while resting behind the rocker molding. Fasten the nut onto the rear stud of the front fender splash shield by tightening it to 4 Nm (35 lb in). Mount the screws first to front fender splash shield at the front bumper fascia while maintaining 2 Nm of torque but tighten later the screws inserted to the front fender splash shield which need to reach 2 Nm (18 lb in). Install a new plastic rivet to the combination of rocker panel and front fender splash shield before fitting the bolt to the front edge of the shield at the side rail under the engine compartment while tightening to 7 Nm (61 lb in). Install new plastic rivets onto the front fascia extension corner as well as the front fender splash shield.

How to replace the rear Fender Splash Shield on Chevrolet Monte Carlo?

Vehicle elevation followed by support is needed before tire removal enables access to the rear wheelhouse splash shield panel. Pull out the three securing screws: one from the rocker panel to rear wheelhouse splash shield section and two from the quarter panel to rear wheelhouse splash shield region along with the single screw from the lower quarter panel to rear wheelhouse splash shield. The J 38778 Door Trim Pad Clip Remover (J 38778) helps uninstall the lower quarter panel to rear wheelhouse splash shield push-in retainer and afterwards enables the removal of the rear wheelhouse splash shield to rear wheelhouse palnuts followed by the removal of the rear wheelhouse splash shield from the vehicle. Chose a proper position for the rear wheelhouse splash shield relative to the wheelhouse then install it on the wheelhouse palnuts while tightening to 2 N.m (18 lb in). You should install the lower quarter panel to rear wheelhouse splash shield push-in retainer followed by lower quarter panel to rear wheelhouse splash shield screw while torquing both components to 2 N.m (18 lb in). Screw and tighten rear wheelhouse splash shield screws of the quarter panel to 2 N.m (18 lb in) before installing the rocker panel to rear wheelhouse splash shield screw which requires a torque of 2 N.m (18 lb in). Reposition the rear tires together with wheels after lowering the vehicle.

OEM Chevrolet Monte Carlo Fender Splash Shield

Wheelhouse Liner

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

26 Fender Splash Shields found

View related parts
Chevrolet Monte Carlo Splash Shield, Passenger Side Part Number: 10349808
$14.30 MSRP: $21.29
You Save: $6.99 (33%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shield-Engine Splash; Fender Splash Shield; Shield, Front Fender Inner Wheel House
- Position: Passenger Side
- Replaces: 10298111
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2007 Chevrolet Monte Carlo | LS, LS Competition, LS Sport, LT, LTZ, SS, SS 35th Anniversary Edition, SS Dale Earnhardt Signature Edition, SS High Sport, SS Pace Car | 6 Cyl 3.4 L GAS, 6 Cyl 3.5 L FLEX, 6 Cyl 3.5 L GAS, 6 Cyl 3.8 L GAS, 6 Cyl 3.9 L GAS
View related parts
Chevrolet Monte Carlo Fender Liner, Front Inner Driver Side Part Number: 15889233
$56.52 MSRP: $84.12
You Save: $27.60 (33%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Liner, Front Fender Inner Wheel House; Fender Splash Shield
- Position: Front Inner Driver Side
- Replaces: 10351085
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2006-2007 Chevrolet Monte Carlo | LS, LT, LTZ, SS | 6 Cyl 3.5 L FLEX, 6 Cyl 3.5 L GAS, 6 Cyl 3.9 L GAS, 8 Cyl 5.3 L GAS
View related parts
Chevrolet Monte Carlo Splash Shield, Black Part Number: 10279931
$38.53
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Shield-Engine Compartment Splash *Black; Fender Splash Shield; Shield, Front Fender Inner Wheel House
- Replaces: 10276601
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1995-1997 Chevrolet Monte Carlo | Z34 | 6 Cyl 3.4 L GAS
View related parts
Chevrolet Monte Carlo Front Panel Part Number: 89025200
$183.21 MSRP: $273.90
You Save: $90.69 (34%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Extension, Front Fender Inner Wheel House
- Position: Front Passenger Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2006-2007 Chevrolet Monte Carlo | LS, LT, LTZ, SS | 6 Cyl 3.5 L FLEX, 6 Cyl 3.5 L GAS, 6 Cyl 3.9 L GAS, 8 Cyl 5.3 L GAS
View related parts
Chevrolet Monte Carlo Fender Liner, Front Passenger Side Part Number: 19120191
$30.59 MSRP: $45.53
You Save: $14.94 (33%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Liner Assembly, Front Wheelhouse (Right-Hand); Fender Splash Shield; Liner, Front Fender Inner Wheel House
- Position: Front Passenger Side
- Replaces: 10290448, 10440209
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2005 Chevrolet Monte Carlo | LS, LS Competition, LS Sport, LT, SS, SS 35th Anniversary Edition, SS Dale Earnhardt Signature Edition, SS High Sport, SS Pace Car | 6 Cyl 3.4 L GAS, 6 Cyl 3.8 L GAS
View related parts
Chevrolet Monte Carlo Splash Shield, Driver Side Part Number: 10349809
$5.47 MSRP: $8.13
You Save: $2.66 (33%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shield-Engine Splash; Fender Splash Shield; Shield, Front Fender Inner Wheel House
- Position: Driver Side
- Replaces: 10298112
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2007 Chevrolet Monte Carlo | LS, LS Competition, LS Sport, LT, LTZ, SS, SS 35th Anniversary Edition, SS Dale Earnhardt Signature Edition, SS High Sport, SS Pace Car | 6 Cyl 3.4 L GAS, 6 Cyl 3.5 L FLEX, 6 Cyl 3.5 L GAS, 6 Cyl 3.8 L GAS, 6 Cyl 3.9 L GAS
View related parts
Chevrolet Monte Carlo Fender Liner, Front Inner Passenger Side Part Number: 15889232
Product Specifications
- Other Name: Liner, Front Fender Inner Wheel House; Fender Splash Shield
- Position: Front Inner Passenger Side
- Replaces: 10351084
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2006-2007 Chevrolet Monte Carlo | LS, LT, LTZ, SS | 6 Cyl 3.5 L FLEX, 6 Cyl 3.5 L GAS, 6 Cyl 3.9 L GAS, 8 Cyl 5.3 L GAS
View related parts
Chevrolet Monte Carlo Fender Liner, Front Inner Driver Side Part Number: 19120192
Product Specifications
- Other Name: Liner, Front Fender Inner Wheel House; Fender Splash Shield
- Position: Front Inner Driver Side
- Replaces: 10290449, 10440210
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2005 Chevrolet Monte Carlo | LS, LS Competition, LS Sport, LT, SS, SS 35th Anniversary Edition, SS Dale Earnhardt Signature Edition, SS High Sport, SS Pace Car | 6 Cyl 3.4 L GAS, 6 Cyl 3.8 L GAS
View related parts
Chevrolet Monte Carlo Fender Liner, Front Inner Passenger Side Part Number: 10280700
Product Specifications
- Other Name: Liner, Front Fender Inner Wheel House; Fender Splash Shield
- Position: Front Inner Passenger Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1995-1999 Chevrolet Monte Carlo | LS, Z34 | 6 Cyl 3.1 L GAS, 6 Cyl 3.4 L GAS, 6 Cyl 3.8 L GAS
View related parts
Chevrolet Monte Carlo Liner, Rear Driver Side Part Number: 15890139
Product Specifications
- Other Name: Liner, Rear Wheelhouse
- Position: Rear Driver Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2006-2007 Chevrolet Monte Carlo | LS, LT, LTZ, SS | 6 Cyl 3.5 L FLEX, 6 Cyl 3.5 L GAS, 6 Cyl 3.9 L GAS, 8 Cyl 5.3 L GAS
View related parts
Chevrolet Monte Carlo Liner, Rear Passenger Side Part Number: 15890140
Product Specifications
- Other Name: Liner, Rear Wheelhouse
- Position: Rear Passenger Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2006-2007 Chevrolet Monte Carlo | LS, LT, LTZ, SS | 6 Cyl 3.5 L FLEX, 6 Cyl 3.5 L GAS, 6 Cyl 3.9 L GAS, 8 Cyl 5.3 L GAS
View related parts
Chevrolet Monte Carlo Splash Shield, Black Part Number: 10279930
Product Specifications
- Other Name: Shield-Engine Compartment Splash *Black; Fender Splash Shield; Shield, Front Fender Inner Wheel House
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1995-1997 Chevrolet Monte Carlo | Z34 | 6 Cyl 3.4 L GAS
View related parts
Chevrolet Monte Carlo Front Panel, Inner Passenger Side Part Number: 10299383
Product Specifications
- Other Name: Extension, Front Fender Inner Wheel House
- Position: Front Inner Passenger Side
- Replaces: 10241006
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2005 Chevrolet Monte Carlo | LS, LS Competition, LS Sport, LT, SS, SS 35th Anniversary Edition, SS Dale Earnhardt Signature Edition, SS High Sport, SS Pace Car | 6 Cyl 3.4 L GAS, 6 Cyl 3.8 L GAS
View related parts
Chevrolet Monte Carlo Liner, Rear Driver Side Part Number: 19120196
Product Specifications
- Other Name: Liner, Rear Wheelhouse
- Position: Rear Driver Side
- Replaces: 10439812
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2005 Chevrolet Monte Carlo | LS, LS Competition, LS Sport, LT, SS, SS 35th Anniversary Edition, SS Dale Earnhardt Signature Edition, SS High Sport, SS Pace Car | 6 Cyl 3.4 L GAS, 6 Cyl 3.8 L GAS
View related parts
Chevrolet Monte Carlo Front Panel, Inner Driver Side Part Number: 10241007
Product Specifications
- Other Name: Extension, Front Fender Inner Wheel House
- Position: Front Inner Driver Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2005 Chevrolet Monte Carlo | LS, LS Competition, LS Sport, LT, SS, SS 35th Anniversary Edition, SS Dale Earnhardt Signature Edition, SS High Sport, SS Pace Car | 6 Cyl 3.4 L GAS, 6 Cyl 3.8 L GAS
View related parts
Chevrolet Monte Carlo Front Panel Part Number: 89025201
Product Specifications
- Other Name: Extension, Front Fender Inner Wheel House
- Position: Front Driver Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2006-2007 Chevrolet Monte Carlo | LS, LT, LTZ, SS | 6 Cyl 3.5 L FLEX, 6 Cyl 3.5 L GAS, 6 Cyl 3.9 L GAS, 8 Cyl 5.3 L GAS
View related parts
Chevrolet Monte Carlo Splash Shield, Driver Side Part Number: 14088057
Product Specifications
- Other Name: Shield-Engine Splash; Fender Splash Shield; Front Deflector; Shield, Front Fender Inner Wheel House
- Position: Driver Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1995-1999 Chevrolet Monte Carlo | LS, Z34 | 6 Cyl 3.1 L GAS, 6 Cyl 3.8 L GAS
View related parts
Chevrolet Monte Carlo Splash Shield, Passenger Side Part Number: 10264192
Product Specifications
- Other Name: Shield-Engine Splash; Fender Splash Shield; Front Deflector; Shield, Front Fender Inner Wheel House
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1995-1999 Chevrolet Monte Carlo | LS, Z34 | 6 Cyl 3.1 L GAS, 6 Cyl 3.8 L GAS
View related parts
Chevrolet Monte Carlo Splash Shield, Front Inner Passenger Side Part Number: 14013480
Product Specifications
- Other Name: Shield, Front Fender Inner Wheel House; Fender Splash Shield
- Position: Front Inner Passenger Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1984-1988 Chevrolet Monte Carlo | Base, SS | 6 Cyl 3.8 L GAS, 6 Cyl 4.3 L GAS, 8 Cyl 5.0 L GAS, 8 Cyl 5.7 L DIESEL
View related parts
Chevrolet Monte Carlo Splash Shield, Front Inner Driver Side Part Number: 14013479
Product Specifications
- Other Name: Shield, Front Fender Inner Wheel House; Fender Splash Shield
- Position: Front Inner Driver Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1984-1988 Chevrolet Monte Carlo | Base, SS | 6 Cyl 3.8 L GAS, 6 Cyl 4.3 L GAS, 8 Cyl 5.0 L GAS, 8 Cyl 5.7 L DIESEL

| Page 1 of 2 |Next >

1-20 of 26 Results

Chevrolet Monte Carlo Fender Splash Shield

Want to cut long-term maintenance and repair costs? Choose OEM Fender Splash Shield. Those parts deliver top durability you can trust. On our site, you'll find a huge catalog of genuine Chevrolet Monte Carlo parts. Prices are unbeatable, so you can keep more in your pocket. Every OEM Chevrolet Monte Carlo Fender Splash Shield includes a manufacturer's warranty. You can also get an easy return policy that keeps buying risk free. Fast delivery, get your car on the road quickly. It's simple to search, compare, and order. Stop guessing about quality or fit. Order today and save with parts that last.

According to Chevrolet Monte Carlo Fender Splash Shield functions as an essential element which demonstrates the reliability and performance features of Chevrolet Monte Carlo automobiles. The Fender Splash Shield protects fenders together with under-the-hood components by shielding them against road debris along with water and corrosive elements which enables the Chevrolet Monte Carlo to function more efficiently and safely. The sixth generation of Chevrolet Monte Carlo features this shield which started with metal panels in early versions then shifted to advanced thermoplastic materials in newer iterations following the Chevrolet promise of evolutionary development and durability across its entire product range. Through its effective design the Fender Splash Shield shields critical components from tire debris and mud which allows other body panels to maintain correct fitment. Car owners benefit from two major advantages with the Fender Splash Shield: extended vehicle life as well as improved handling performance. The lightweight construction of the Fender Splash Shield delivers more fuel efficiency to vehicles which positions it as an outstanding feature within the automotive sector. Chevrolet Monte Carlo Fender Splash Shield establishes itself as mandatory equipment for Monte Carlo drivers who want to protect their vehicle while maintaining safety. Through engineering excellence the brand has made the Fender Splash Shield a vital part of the the automaker model's historical success.

Chevrolet Monte Carlo Fender Splash Shield Parts and Q&A

Splash Shield, Passenger Side
10349808
Q: How to replace the front Fender Splash Shield on Chevrolet Monte Carlo?
A:
The procedure for front fender splash shield replacement begins by drilling out plastic rivets from the front fascia extension corner to the front fender splash shield when the vehicle has this configuration. You should start by removing the front fender splash shield screws from the front bumper fascia area and the nut from the stud located near the rear of the front fender splash shield and the bolt securing the front tab on the front fender splash shield at the lower engine compartment side rail. Start by drilling the plastic rivet connecting the front rocker panel to the front fender splash shield whenever present followed by the removal of front fender splash shield screws. Fix the splash shield along the fender while reaching over the stud while resting behind the rocker molding. Fasten the nut onto the rear stud of the front fender splash shield by tightening it to 4 Nm (35 lb in). Mount the screws first to front fender splash shield at the front bumper fascia while maintaining 2 Nm of torque but tighten later the screws inserted to the front fender splash shield which need to reach 2 Nm (18 lb in). Install a new plastic rivet to the combination of rocker panel and front fender splash shield before fitting the bolt to the front edge of the shield at the side rail under the engine compartment while tightening to 7 Nm (61 lb in). Install new plastic rivets onto the front fascia extension corner as well as the front fender splash shield.
Splash Shield, Driver Side
10349809
Q: How to replace the rear Fender Splash Shield on Chevrolet Monte Carlo?
A:
Vehicle elevation followed by support is needed before tire removal enables access to the rear wheelhouse splash shield panel. Pull out the three securing screws: one from the rocker panel to rear wheelhouse splash shield section and two from the quarter panel to rear wheelhouse splash shield region along with the single screw from the lower quarter panel to rear wheelhouse splash shield. The J 38778 Door Trim Pad Clip Remover (J 38778) helps uninstall the lower quarter panel to rear wheelhouse splash shield push-in retainer and afterwards enables the removal of the rear wheelhouse splash shield to rear wheelhouse palnuts followed by the removal of the rear wheelhouse splash shield from the vehicle. Chose a proper position for the rear wheelhouse splash shield relative to the wheelhouse then install it on the wheelhouse palnuts while tightening to 2 N.m (18 lb in). You should install the lower quarter panel to rear wheelhouse splash shield push-in retainer followed by lower quarter panel to rear wheelhouse splash shield screw while torquing both components to 2 N.m (18 lb in). Screw and tighten rear wheelhouse splash shield screws of the quarter panel to 2 N.m (18 lb in) before installing the rocker panel to rear wheelhouse splash shield screw which requires a torque of 2 N.m (18 lb in). Reposition the rear tires together with wheels after lowering the vehicle.