How to ensure proper installation of an emblem on a Chevrolet S10?

You need to protect the mounting surface with tape before you install an Emblem/nameplate on the pickup box while using tape for alignment reference points. Use a j 25070 (Heat Gun) to apply circular heat over the Emblem/nameplate for 30 seconds before lifting or removing it with a j 41409 (Body Molding Removal Tool) from the panel surface. Keep the tape on the molding and panel unless it becomes damaged in which case the Emblem/nameplate replacement can proceed. Use adhesive cleaner with a lint-free cloth to clean both the tape and mating surface before proceeding. Continue with the replacement if you observe any damage on the tape. Place the adhesive foam tape onto the back of the new Emblem/nameplate before pressing it onto the surface. To remove adhesive residue on body panels apply 3m(TM) scotch brite molding adhesive remover disk (3M(TM) p/n 07501). However for plastic panels use varnish makers and painters (VMP) naphtha or a 50/50 isopropyl alcohol and water solution with a lint-free cloth. The installation area must be cleared of dust and dirt before cleaning it with a lint-free cloth and the same cleaning solution until it dries completely. Organize placement marks 135 mm facing forward from the Tail Light and 330 mm away from the quarter panel ditch unless already present. Heat the mounting area to a temperature range between 27-41°c (80-105°F) while keeping the Emblem/nameplate at 29-32°c (85-90°F). Apply firm pressure across the entire mounting surface after positioning the Emblem or nameplate so it lines up with the measured marks. After completion you should peel off protective tape from the mounting surface.

How to replace or repair an emblem/nameplate on a pickup box on Chevrolet S10?

You can start the pickup box Emblem/nameplate repair by covering the surface with tape before you use tape to mark its placement during assembly. Warm the Emblem/nameplate with j 25070 heat gun (J 25070) in slow circles for 30 seconds afterward use j 41409 body molding removal tool (J 41409) to pull it off the panel surface. Keep the tape attached and work with cleaning supplies to handle the intact tape along with the mating surface. Handle a new replacement when the tape sustains harm. Stick adhesive foam tape onto the back of the new Emblem/nameplate and press it onto its designated location. Use a 3m(TM) scotch brite molding adhesive remover disk model 07501 for body panel parts or rub with varnish makers and painters naphtha and water solution through a lint-free cloth for plastic parts. Dust the installation area clean and prepare it using a lint-free cloth dipped in the same cleaning solution. Then fully dry the area before proceeding. Set the installation point 135 mm forward of the Tail Light and 330 mm from the quarterpanel ditch unless marked earlier. Heat the mounting surface to between 27 and 41 degrees celsius (80 to 105 degrees Fahrenheit) as you keep the Emblem/nameplate at 29 to 32 degrees celsius (85 to 90 degrees Fahrenheit). After trimming the protective layer on the back of the Emblem/nameplate apply it to its marked position on the mounting surface then press down evenly across its entire surface. Take away the protective film from its intended area of installation.

OEM Chevrolet S10 Emblem

Badge

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

23 Emblems found

View related parts
Chevrolet S10 Nameplate, Rear Part Number: 15126056
$60.07 MSRP: $89.40
You Save: $29.33 (33%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Plate, End Gate And Rear Door Decoration; Emblem, Radiator Grille And Front End Ornamentation
- Position: Rear
- Replaces: 15034749, 15053248, 15675118, 15982992, 15998983
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1996-2004 Chevrolet S10 | Base, LS, SS, Xtreme, ZR2, ZR5 | 4 Cyl 2.2 L FLEX, 4 Cyl 2.2 L GAS, 6 Cyl 4.3 L GAS
View related parts
Chevrolet S10 Nameplate, Outer Part Number: 15053247
$128.62 MSRP: $192.29
You Save: $63.67 (34%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Plate, Cab And Load Carrier Outer Side Decoration; Plate Assembly, Cab And Load Carrier Outer Side Decoration; Plate, End Gate And Rear Door Decoration
- Position: Outer
- Replaces: 15034748
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1999-2003 Chevrolet S10 | Base, LS, Xtreme, ZR2, ZR5 | 4 Cyl 2.2 L FLEX, 4 Cyl 2.2 L GAS, 6 Cyl 4.3 L GAS
View related parts
Chevrolet S10 Emblem, Gold Part Number: 15634687
Product Specifications
- Other Name: Emblem Kit, Radiator Grille; Emblem Kit, Radiator Grille And Front End Ornamentation
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1998-2004, 1991-1993 Chevrolet S10 | Baja, Base, EL, LS, SS, Tahoe, Xtreme, ZR2, ZR5 | 4 Cyl 2.2 L FLEX, 4 Cyl 2.2 L GAS, 4 Cyl 2.5 L GAS, 6 Cyl 2.8 L GAS, 6 Cyl 4.3 L GAS
View related parts
Chevrolet S10 Emblem, Gold Part Number: 12543579
Product Specifications
- Other Name: Emblem Kit, Radiator Grille; Emblem Kit, Radiator Grille And Front End Ornamentation
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1994-1997 Chevrolet S10 | Base, LS, SS, ZR2 | 4 Cyl 2.2 L GAS, 6 Cyl 4.3 L GAS
View related parts
Chevrolet S10 Emblem, Black; Red, Front Part Number: 15635564
Product Specifications
- Other Name: Emblem Kit, Radiator Grille And Front End Ornamentation
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1998-1999, 1991 Chevrolet S10 | Baja, Base, LS, SS, Tahoe, Xtreme, ZR2 | 4 Cyl 2.2 L GAS, 4 Cyl 2.5 L GAS, 6 Cyl 2.8 L GAS, 6 Cyl 4.3 L GAS
View related parts
Chevrolet S10 Nameplate, Rear Part Number: 15629983
Product Specifications
- Other Name: Plate, End Gate And Rear Door Decoration; Plate Assembly, Cab And Load Carrier Outer Side Decoration; Plate, Cab And Load Carrier Outer Side Decoration
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1991-2004 Chevrolet S10 | Baja, Base, EL, LS, SS, Tahoe, Xtreme, ZR2, ZR5 | 4 Cyl 2.2 L FLEX, 4 Cyl 2.2 L GAS, 4 Cyl 2.5 L GAS, 6 Cyl 2.8 L GAS, 6 Cyl 4.3 L GAS
View related parts
Chevrolet S10 Insert Part Number: 15613332
Product Specifications
- Other Name: Insert, Wheel Cover Appearance; Emblem, Wheel Cover Appearance
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1990-1993 Chevrolet S10 | Baja, Base, Durango, EL, Tahoe | 4 Cyl 2.5 L GAS, 6 Cyl 2.8 L GAS, 6 Cyl 4.3 L GAS
View related parts
Chevrolet S10 Nameplate Part Number: 15597019
Product Specifications
- Other Name: Plate
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1985-1989 Chevrolet S10 | Base, Durango, Sport, Tahoe | 4 Cyl 1.9 L GAS, 4 Cyl 2.2 L DIESEL, 4 Cyl 2.5 L GAS, 6 Cyl 2.8 L GAS, 6 Cyl 4.3 L GAS
View related parts
Chevrolet S10 Nameplate Part Number: 15629991
Product Specifications
- Other Name: Plate, Body Side Name; Plate, Cab And Load Carrier Outer Side Decoration; Plate, Side Panel Wheel Opening
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1991-1993 Chevrolet S10 | Baja, Base, EL, Tahoe | 4 Cyl 2.5 L GAS, 6 Cyl 2.8 L GAS, 6 Cyl 4.3 L GAS
View related parts
Chevrolet S10 Nameplate, Front Part Number: 15592812
Product Specifications
- Other Name: Plate, Front Fender Name
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1985-1989 Chevrolet S10 | Base, Durango, Sport, Tahoe | 4 Cyl 1.9 L GAS, 4 Cyl 2.2 L DIESEL, 4 Cyl 2.5 L GAS, 6 Cyl 2.8 L GAS, 6 Cyl 4.3 L GAS
View related parts
Chevrolet S10 Nameplate Part Number: 15629993
Product Specifications
- Other Name: Plate, Body Side Name; Plate Assembly, Cab And Load Carrier Outer Side Decoration; Side Panel Wheel Opening.
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1991-1993 Chevrolet S10 | Baja, Base, EL, Tahoe | 4 Cyl 2.5 L GAS, 6 Cyl 2.8 L GAS, 6 Cyl 4.3 L GAS
View related parts
Chevrolet S10 Emblem, Front Part Number: 12545719
Product Specifications
- Other Name: Emblem Kit, Radiator Grille And Front End Ornamentation
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1994-1997 Chevrolet S10 | Base, LS, SS, ZR2 | 4 Cyl 2.2 L GAS, 6 Cyl 4.3 L GAS
View related parts
Chevrolet S10 Emblem, Front Part Number: 15591449
Product Specifications
- Other Name: Emblem, Radiator Grille And Front End Ornamentation
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1985-1990 Chevrolet S10 | Base, Durango, Sport, Tahoe | 4 Cyl 1.9 L GAS, 4 Cyl 2.2 L DIESEL, 4 Cyl 2.5 L GAS, 6 Cyl 2.8 L GAS, 6 Cyl 4.3 L GAS
View related parts
Chevrolet S10 Emblem, Outer Part Number: 14057640
Product Specifications
- Other Name: Emblem, Cab And Load Carrier Outer Side Decoration; Nameplate
- Position: Outer
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1985-1993 Chevrolet S10 | Baja, Base, Durango, EL, Sport, Tahoe | 4 Cyl 1.9 L GAS, 4 Cyl 2.2 L DIESEL, 4 Cyl 2.5 L GAS, 6 Cyl 2.8 L GAS, 6 Cyl 4.3 L GAS
View related parts
Chevrolet S10 Decal, Rear Part Number: 15672065
Product Specifications
- Other Name: Plate, End Gate And Rear Door Decoration
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1994-1996 Chevrolet S10 | Base, LS, SS, ZR2 | 4 Cyl 2.2 L GAS, 6 Cyl 4.3 L GAS
View related parts
Chevrolet S10 Tail Gate Trim, Rear Part Number: 15976634
Product Specifications
- Other Name: Plate, End Gate And Rear Door Decoration; Applique
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1991-1993 Chevrolet S10 | Baja, Base, EL, Tahoe | 4 Cyl 2.5 L GAS, 6 Cyl 2.8 L GAS, 6 Cyl 4.3 L GAS
View related parts
Chevrolet S10 Applique, Rear Part Number: 14035975
Product Specifications
- Other Name: Plate, End Gate And Rear Door Decoration
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1985-1990 Chevrolet S10 | Base, Durango, Sport, Tahoe | 4 Cyl 1.9 L GAS, 4 Cyl 2.2 L DIESEL, 4 Cyl 2.5 L GAS, 6 Cyl 2.8 L GAS, 6 Cyl 4.3 L GAS
View related parts
Chevrolet S10 Nameplate, Front Part Number: 15629984
Product Specifications
- Other Name: Plate, Front Side Door; Plate, Cab And Load Carrier Outer Side Decoration
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1991-1993 Chevrolet S10 | Baja, Base, EL, Tahoe | 4 Cyl 2.5 L GAS, 6 Cyl 2.8 L GAS, 6 Cyl 4.3 L GAS
View related parts
Chevrolet S10 Nameplate, Passenger Side Part Number: 1254540
Product Specifications
- Other Name: Emblem-Front Fender; Plate, Front Fender Name
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1985-1989 Chevrolet S10 | Base, Durango, Sport, Tahoe | 6 Cyl 2.8 L GAS, 6 Cyl 4.3 L GAS
View related parts
Chevrolet S10 Nameplate, Rear Part Number: 15632658
Product Specifications
- Other Name: Plate, End Gate And Rear Door Decoration
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1991-1993 Chevrolet S10 | Baja, Base, EL, Tahoe | 6 Cyl 4.3 L GAS

| Page 1 of 2 |Next >

1-20 of 23 Results

Chevrolet S10 Emblem

Want to cut long-term maintenance and repair costs? Choose OEM Emblem. Those parts deliver top durability you can trust. On our site, you'll find a huge catalog of genuine Chevrolet S10 parts. Prices are unbeatable, so you can keep more in your pocket. Every OEM Chevrolet S10 Emblem includes a manufacturer's warranty. You can also get an easy return policy that keeps buying risk free. Fast delivery, get your car on the road quickly. It's simple to search, compare, and order. Stop guessing about quality or fit. Order today and save with parts that last.

A distinctive emblem on Chevrolet S10 trucks represents both exceptional reliability characteristics and exceptional performance abilities that demonstrate brand dedication to developing high-quality compact pickup truck models. The Chevrolet S10 Emblem adorns both the front hood and trunk resulting in dual functions that serve as manufacturer designation while increasing truck visual appeal so the vehicle stands out from other automotive choices. Through its three generations the Chevrolet S10 Emblem executed design modifications that showed S10 development while ensuring its main purpose remained as brand recognition. The Chevrolet S10 provides users with versatile engine choices from its initial 1.9 L LR1 I4 engine to its present-day 2.4 L Flexpower and 2.8 L Duramax diesel options that are both enhanced by the emblem. This emblem confirms the S10's capability to link with multiple models while maintaining Chevrolet's specialty for effective performance and safety measures throughout each update. The Chevrolet car attracts multiple users because it combines a roomy cabin with strong body structure among its special characteristics. The car Emblem combines unique finishing techniques and color selection to represent vehicle line history while showcasing the automaker's long-standing excellence in compact pickup production which proves the model model's reliability as a top performance vehicle for drivers.

Chevrolet S10 Emblem Parts and Q&A

Nameplate, Rear
15126056
Q: How to ensure proper installation of an emblem on a Chevrolet S10?
A:
You need to protect the mounting surface with tape before you install an Emblem/nameplate on the pickup box while using tape for alignment reference points. Use a j 25070 (Heat Gun) to apply circular heat over the Emblem/nameplate for 30 seconds before lifting or removing it with a j 41409 (Body Molding Removal Tool) from the panel surface. Keep the tape on the molding and panel unless it becomes damaged in which case the Emblem/nameplate replacement can proceed. Use adhesive cleaner with a lint-free cloth to clean both the tape and mating surface before proceeding. Continue with the replacement if you observe any damage on the tape. Place the adhesive foam tape onto the back of the new Emblem/nameplate before pressing it onto the surface. To remove adhesive residue on body panels apply 3m(TM) scotch brite molding adhesive remover disk (3M(TM) p/n 07501). However for plastic panels use varnish makers and painters (VMP) naphtha or a 50/50 isopropyl alcohol and water solution with a lint-free cloth. The installation area must be cleared of dust and dirt before cleaning it with a lint-free cloth and the same cleaning solution until it dries completely. Organize placement marks 135 mm facing forward from the Tail Light and 330 mm away from the quarter panel ditch unless already present. Heat the mounting area to a temperature range between 27-41°c (80-105°F) while keeping the Emblem/nameplate at 29-32°c (85-90°F). Apply firm pressure across the entire mounting surface after positioning the Emblem or nameplate so it lines up with the measured marks. After completion you should peel off protective tape from the mounting surface.
Nameplate, Outer
15053247
Q: How to replace or repair an emblem/nameplate on a pickup box on Chevrolet S10?
A:
You can start the pickup box Emblem/nameplate repair by covering the surface with tape before you use tape to mark its placement during assembly. Warm the Emblem/nameplate with j 25070 heat gun (J 25070) in slow circles for 30 seconds afterward use j 41409 body molding removal tool (J 41409) to pull it off the panel surface. Keep the tape attached and work with cleaning supplies to handle the intact tape along with the mating surface. Handle a new replacement when the tape sustains harm. Stick adhesive foam tape onto the back of the new Emblem/nameplate and press it onto its designated location. Use a 3m(TM) scotch brite molding adhesive remover disk model 07501 for body panel parts or rub with varnish makers and painters naphtha and water solution through a lint-free cloth for plastic parts. Dust the installation area clean and prepare it using a lint-free cloth dipped in the same cleaning solution. Then fully dry the area before proceeding. Set the installation point 135 mm forward of the Tail Light and 330 mm from the quarterpanel ditch unless marked earlier. Heat the mounting surface to between 27 and 41 degrees celsius (80 to 105 degrees Fahrenheit) as you keep the Emblem/nameplate at 29 to 32 degrees celsius (85 to 90 degrees Fahrenheit). After trimming the protective layer on the back of the Emblem/nameplate apply it to its marked position on the mounting surface then press down evenly across its entire surface. Take away the protective film from its intended area of installation.