How to replace the ABS Control Module on GMC Canyon?

Before ABS Control Module replacement, workers should use clean paper and shop towels for placement between the ABS Control Module assembly and inner fender. Disconnect the electrical connector from the ABS Control Module, then move it to the position behind the Brake Booster. Clean both module and master cylinder with de-natured alcohol before extracting brake pipes running between these parts. Also, pull away the rear brake pipe from cowl retaining points. Brake fluid leakage and contaminant entry will be minimized by putting rubber plugs into both the brake pressure modulator valve (BPMV) and master cylinder. The ABS Control Module extraction process starts with removing its mounting nuts followed by taking out the unit from the vehicle and positioning it on its side. The abs module requires 4 mounting screws that must be removed carefully before replacement of new screws. The abs module assembly needs replacement instead of attempting to fix damaged screws when they break during uninstallation. Use new collars to replace the 4 components which separate the ABS Control Module from the bpmv. When separating the ABS Control Module from the bpmv within the abs module, prevent the use of pry bars; if separation is impossible, then replace the abs module as a whole unit. Following ABS Control Module and bpmv separation, discard both solenoid plate and o-rings, then use a clean paper towel to clean the bpmv assembly while avoiding shop towels or brake cleaner. The examination of solenoids along with bpmv surface for signs of contamination or corrosion must lead to bpmv assembly replacement when needed. Affix the new solenoid plate with o-rings to the ABS Control Module afterward, adding the bpmv to the assembly, then secure the new collars before tightening their screws to 5 nm (44 inch lbs.) while performing a finger tighten first. The abs module installation must include a 9 nm (80 inch lbs.) torque value while tightening the mounting nuts correctly. The replacement process requires removal of rubber plugs from brake pipes and ABS Control Module assembly until you can install brake pipes onto the ABS Control Module assembly while applying 19 nm (14 ft. Lbs.) torque after initial finger tightening. The final steps require users to reconnect the electrical connector and install the rear brake pipe within the cowl retainer before they remove all paper or shop towels from between the ABS Control Module assembly and inner fender. Then the system requires abs brake bleeding to complete.

OEM GMC Canyon ABS Control Module

Anti Lock Brake Control Module

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

13 ABS Control Modules found

View related parts
GMC Canyon Control Module Part Number: 84330122
$254.38 MSRP: $498.06
You Save: $243.68 (49%)
ADD TO CART
Product Specifications
- Other Name: Module, Electronic Brake Control; ABS Control Module
- Replaces: 84214765, 84004231
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2017-2022 GMC Canyon | All Terrain, AT4, Base, Denali, Elevation, Elevation Standard, SL, SLE, SLT | 4 Cyl 2.5 L GAS, 4 Cyl 2.8 L DIESEL, 6 Cyl 3.6 L GAS
View related parts
GMC Canyon Modulator Valve Part Number: 84644579
$392.68 MSRP: $762.13
You Save: $369.45 (49%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Module Assembly-Electronic Brake Control (W/Brake Pressure Mode; ABS Control Module; ABS Control Unit; Module, Electronic Brake Control
- Replaces: 84004228, 84330123, 84214766, 84338036
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2017-2022 GMC Canyon | All Terrain, AT4, Base, Denali, Elevation, Elevation Standard, SL, SLE, SLT | 4 Cyl 2.5 L GAS, 4 Cyl 2.8 L DIESEL, 6 Cyl 3.6 L GAS
View related parts
GMC Canyon ABS Control Unit Part Number: 23414478
$477.56 MSRP: $883.54
You Save: $405.98 (46%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Module Assembly-Electronic Brake Control (W/Brake Pressure Mode; ABS Control Module; Module, Electronic Brake Control
- Replaces: 23284603
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2016 GMC Canyon | Base, SL, SLE, SLT | 4 Cyl 2.5 L GAS, 4 Cyl 2.8 L DIESEL, 6 Cyl 3.6 L GAS
View related parts
GMC Canyon Control Module Part Number: 19207520
Product Specifications
- Other Name: Module Kit, Electronic Brake Control; ABS Control Module
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2010-2012 GMC Canyon | SLE, SLT, WT | 4 Cyl 2.9 L GAS, 5 Cyl 3.7 L GAS, 8 Cyl 5.3 L GAS
View related parts
GMC Canyon Control Module Part Number: 19121732
Product Specifications
- Other Name: Module Assembly, Electronic Brake Control; ABS Control Module; Module, Electronic Brake Control
- Replaces: 88967058, 19149182, 89040345
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2004-2009 GMC Canyon | SL, SLE, SLT, WT, Z71 Fleet, Z71 SL, Z71 SLE, Z85 SL, Z85 SLE | 4 Cyl 2.8 L GAS, 4 Cyl 2.9 L GAS, 5 Cyl 3.5 L GAS, 5 Cyl 3.7 L GAS, 8 Cyl 5.3 L GAS
View related parts
GMC Canyon Control Module Part Number: 19121730
Product Specifications
- Other Name: Module Assembly, Electronic Brake Control; ABS Control Module; Module, Electronic Brake Control
- Replaces: 19149180, 89040343, 88967056
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2004-2009 GMC Canyon | SL, SLE, SLT, WT, Z71 Fleet, Z71 SL, Z71 SLE, Z85 SL, Z85 SLE | 4 Cyl 2.8 L GAS, 4 Cyl 2.9 L GAS, 5 Cyl 3.5 L GAS, 5 Cyl 3.7 L GAS, 8 Cyl 5.3 L GAS
View related parts
GMC Canyon ABS Control Unit Part Number: 19121728
Product Specifications
- Other Name: Module Assembly, Electronic Brake Control; ABS Control Module; Module, Electronic Brake Control
- Replaces: 88967054, 19149184, 88964186
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2004-2008 GMC Canyon | SL, SLE, SLT, WT, Z71 Fleet, Z71 SL, Z71 SLE, Z85 SL, Z85 SLE | 4 Cyl 2.8 L GAS, 4 Cyl 2.9 L GAS, 5 Cyl 3.5 L GAS, 5 Cyl 3.7 L GAS
View related parts
GMC Canyon Control Module Part Number: 85620555
Product Specifications
- Other Name: Module Kit-Electronic Brake Control; Module Kit, Electronic Brake Control
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2023 GMC Canyon | AT4, AT4X, Denali, Elevation | 4 Cyl 2.7 L GAS
View related parts
GMC Canyon Control Module Part Number: 19121731
Product Specifications
- Other Name: Module Assembly, Electronic Brake Control; ABS Control Module; Module, Electronic Brake Control
- Replaces: 88967057, 89040344
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2004-2009 GMC Canyon | SL, SLE, SLT, WT, Z71 Fleet, Z71 SL, Z71 SLE, Z85 SL, Z85 SLE | 4 Cyl 2.8 L GAS, 4 Cyl 2.9 L GAS, 5 Cyl 3.5 L GAS, 5 Cyl 3.7 L GAS, 8 Cyl 5.3 L GAS
View related parts
GMC Canyon ABS Control Unit Part Number: 19121729
Product Specifications
- Other Name: Module Assembly, Electronic Brake Control; ABS Control Module; Module, Electronic Brake Control
- Replaces: 19149185, 88964188, 88967055, 89040661
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2004-2008 GMC Canyon | SL, SLE, SLT, WT, Z71 Fleet, Z71 SL, Z71 SLE, Z85 SL, Z85 SLE | 4 Cyl 2.8 L GAS, 4 Cyl 2.9 L GAS, 5 Cyl 3.5 L GAS, 5 Cyl 3.7 L GAS
View related parts
GMC Canyon ABS Control Unit Part Number: 19121727
Product Specifications
- Other Name: Module Assembly, Electronic Brake Control; ABS Control Module; Module, Electronic Brake Control
- Replaces: 89040659, 19149183, 88967053
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2004-2008 GMC Canyon | SL, SLE, SLT, WT, Z71 Fleet, Z71 SL, Z71 SLE, Z85 SL, Z85 SLE | 4 Cyl 2.8 L GAS, 4 Cyl 2.9 L GAS, 5 Cyl 3.5 L GAS, 5 Cyl 3.7 L GAS
View related parts
GMC Canyon Control Module Part Number: 23414480
$248.88 MSRP: $446.45
You Save: $197.57 (45%)
Product Specifications
- Other Name: Module Kit-Electronic Brake Control; ABS Control Module; Modulator Valve; Module Kit, Electronic Brake Control
- Replaces: 23200278
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2015-2016 GMC Canyon | Base, SL, SLE, SLT | 4 Cyl 2.5 L GAS, 4 Cyl 2.8 L DIESEL, 6 Cyl 3.6 L GAS
View related parts
GMC Canyon Modulator Valve Part Number: 23354053
$609.11 MSRP: $1097.49
You Save: $488.38 (45%)
Product Specifications
- Other Name: Module, Electronic Brake Control; ABS Control Module; ABS Control Unit
- Replaces: 23200277
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2015 GMC Canyon | Base, SL, SLE, SLT | 4 Cyl 2.5 L GAS, 6 Cyl 3.6 L GAS

GMC Canyon ABS Control Module

Want to cut long-term maintenance and repair costs? Choose OEM ABS Control Module. Those parts deliver top durability you can trust. On our site, you'll find a huge catalog of genuine GMC Canyon parts. Prices are unbeatable, so you can keep more in your pocket. Every OEM GMC Canyon ABS Control Module includes a manufacturer's warranty. You can also get an easy return policy that keeps buying risk free. Fast delivery, get your car on the road quickly. It's simple to search, compare, and order. Stop guessing about quality or fit. Order today and save with parts that last.

The GMC Canyon ABS Control Module is an essential subsystem that highlights the GMC advanced reliability and high performance strategy of Canyon models. This module is highly significant for diagnosing and managing the ABS modulator, thus avoiding wheel lock during severe braking, which in turn increases manoeuvrability of the car and protects it from skidding. Applicable to the GMC Canyon's different versions, the ABS Control Module interfaces with the wheel speed sensors, valves, a pump and the ECU to simulate and control the braking procedures using sensor data and alter the van-driving braking force output. This integration not only enhances the control of the vehicle but also dramatically decreases the stopping distance over various terrains so it is crucial. The enhancement of the kind of technology used in the ABS system has also included features such as the electronic stability control and also the control of tractions making the GMC Canyon very safe for drivers and passengers. The GMC Canyon was first launched in the year 2004 and from then on, the vehicle was designed for flexibility and versatility, such as, the type of drive it is provided either as two-wheel or four-wheel drive and type of suspension presented. Right now, in the world market, the ABS Control Module has a reputation for delivering efficiency and safety in automotive vehicles; so much so that every GMC Canyon will not fail to respond to the driver's desire for safety and efficiency on the road. Thanks to the reliable engineering and unique solutions, the GMC Canyon ABS Control Module is a vivid evidence of GMC's commitment to the premium vehicles quality and safety.

GMC Canyon ABS Control Module Parts and Q&A

Control Module
19121730
Q: How to replace the ABS Control Module on GMC Canyon?
A:
Before ABS Control Module replacement, workers should use clean paper and shop towels for placement between the ABS Control Module assembly and inner fender. Disconnect the electrical connector from the ABS Control Module, then move it to the position behind the Brake Booster. Clean both module and master cylinder with de-natured alcohol before extracting brake pipes running between these parts. Also, pull away the rear brake pipe from cowl retaining points. Brake fluid leakage and contaminant entry will be minimized by putting rubber plugs into both the brake pressure modulator valve (BPMV) and master cylinder. The ABS Control Module extraction process starts with removing its mounting nuts followed by taking out the unit from the vehicle and positioning it on its side. The abs module requires 4 mounting screws that must be removed carefully before replacement of new screws. The abs module assembly needs replacement instead of attempting to fix damaged screws when they break during uninstallation. Use new collars to replace the 4 components which separate the ABS Control Module from the bpmv. When separating the ABS Control Module from the bpmv within the abs module, prevent the use of pry bars; if separation is impossible, then replace the abs module as a whole unit. Following ABS Control Module and bpmv separation, discard both solenoid plate and o-rings, then use a clean paper towel to clean the bpmv assembly while avoiding shop towels or brake cleaner. The examination of solenoids along with bpmv surface for signs of contamination or corrosion must lead to bpmv assembly replacement when needed. Affix the new solenoid plate with o-rings to the ABS Control Module afterward, adding the bpmv to the assembly, then secure the new collars before tightening their screws to 5 nm (44 inch lbs.) while performing a finger tighten first. The abs module installation must include a 9 nm (80 inch lbs.) torque value while tightening the mounting nuts correctly. The replacement process requires removal of rubber plugs from brake pipes and ABS Control Module assembly until you can install brake pipes onto the ABS Control Module assembly while applying 19 nm (14 ft. Lbs.) torque after initial finger tightening. The final steps require users to reconnect the electrical connector and install the rear brake pipe within the cowl retainer before they remove all paper or shop towels from between the ABS Control Module assembly and inner fender. Then the system requires abs brake bleeding to complete.