How to replace the Brake Calipers on GMC Canyon?

Lift the vehicle into position and support it properly at the beginning of brake caliper replacement. Take the wheel with tire off the vehicle. Replace the brake hose fitting gaskets with new ones during your work. Separate the brake caliper from its brake hose fitting by first taking off the bolt and secondly removing the gaskets then the brake fitting. Place a fitting cap on the hose to maintain the brake fluid supply during replacement. Once raised and supported, you must remove first the brake caliper guide pin bolts and then the brake caliper itself. Install the brake caliper at first and make sure to put the brake caliper guide pin bolts into place while tightening them to 64Nm (47 lb ft). Insert fresh brake hose gaskets when connecting the brake hose fitting bolt and gaskets to the brake hose fitting. Fix the brake hose assembly to the caliper and wrench-tighten the fitting bolt to 40 Nm (30 lb ft). After bleeding the brake lines you will put on the tire wheel unit.

How to Service and Repair Brake Calipers on GMC Canyon?

Before servicing the brake caliper you need to drain all brake fluid out of the caliper unit. Never put your fingers before a Piston during compressed air use because the outcome can harm you severely. During brake caliper removal you may experience damage to the Piston which needs replacement by a new one. Hang the brake caliper in a safe device then wedge in a timber part before placing a shop towel over it. Compressed filtered air without lubricate helps you take out the brake caliper pistons. Position the taken Piston back into the caliper. Then use a small wood block and a c-clamp with compressed air to force the Piston halfway inside. Place another block of wood ahead of the final Piston and repeat the air application. Push out three pistons from each caliper barrel and afterward two Piston seals without using metal tools. Disconnect the bleeder valve components from the caliper housing and cleanse them all with denatured alcohol before drying them under compressed air filtration. Replace smooth caliper bores either with new pistons or a new caliper before installing unharmed boots back into place. Discard brake caliper debris by cleaning the parts with denatured alcohol before air drying them using compressed lubricated air. Apply brake fluid sparingly onto the Piston dust seal as you place the Piston seal and strut spring using the boot seal installer (J 45863). Put the Piston in place only when it stands flat and straight. Press down the Piston using wood as a buffer and then take away the wooden tool when installation is complete. At last install the Piston dust seal using a driver handle and boot seal installer. Install the bleeder valve and tighten it to 19 nm (14 ft. Lbs.) before covering it with its cap.

OEM GMC Canyon Brake Calipers

Caliper

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

17 Brake Calipers found

View related parts
GMC Canyon Caliper Assembly, Rear Driver Side Part Number: 23387175
$77.08 MSRP: $149.26
You Save: $72.18 (49%)
ADD TO CART
Product Specifications
- Other Name: Caliper Assembly-Rear Brake (W/O Brake Pads & Bracket; Brake Caliper; Caliper; Caliper, Wheel Brake Cylinder/Caliper
- Position: Rear Driver Side
- Replaces: 23249394
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2015-2020 GMC Canyon | All Terrain, Base, Denali, SL, SLE, SLT | 4 Cyl 2.5 L GAS, 4 Cyl 2.8 L DIESEL, 6 Cyl 3.6 L GAS
View related parts
GMC Canyon Caliper Assembly, Rear Passenger Side Part Number: 23387174
$77.08 MSRP: $149.26
You Save: $72.18 (49%)
ADD TO CART
Product Specifications
- Other Name: Caliper Assembly-Rear Brake (W/O Brake Pads & Bracket; Brake Caliper; Caliper; Caliper, Wheel Brake Cylinder/Caliper
- Position: Rear Passenger Side
- Replaces: 23249393
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2015-2020 GMC Canyon | All Terrain, Base, Denali, SL, SLE, SLT | 4 Cyl 2.5 L GAS, 4 Cyl 2.8 L DIESEL, 6 Cyl 3.6 L GAS
View related parts
GMC Canyon Caliper Part Number: 21998527
$111.31 MSRP: $216.26
You Save: $104.95 (49%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper Assembly, Front Brake (W/O Brake Pads & Bracket); Brake Caliper; Caliper, Wheel Brake Cylinder/Caliper
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2009-2012 GMC Canyon | SLE, SLT, WT | 4 Cyl 2.9 L GAS, 5 Cyl 3.7 L GAS, 8 Cyl 5.3 L GAS
View related parts
GMC Canyon Caliper Part Number: 21998526
$102.52 MSRP: $199.08
You Save: $96.56 (49%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper Assembly, Front Brake (W/O Brake Pads & Bracket); Brake Caliper; Caliper, Wheel Brake Cylinder/Caliper
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2009-2012 GMC Canyon | SLE, SLT, WT | 4 Cyl 2.9 L GAS, 5 Cyl 3.7 L GAS, 8 Cyl 5.3 L GAS
View related parts
GMC Canyon Caliper, Driver Side Part Number: 87837859
$118.32 MSRP: $212.24
You Save: $93.92 (45%)
ADD TO CART
Product Specifications
- Other Name: Caliper Assembly-Front Brake (W/O Brake Pads & Bracket); Caliper, Wheel Brake Cylinder/Caliper
- Position: Driver Side
- Replaced by: 85786975
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2023 GMC Canyon | AT4, AT4X, Denali, Elevation | 4 Cyl 2.7 L GAS
View related parts
GMC Canyon Caliper, Driver Side Part Number: 84737985
$126.81 MSRP: $254.69
You Save: $127.88 (51%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper, Wheel Brake Cylinder/Caliper
- Position: Driver Side
- Replaces: 23249389, 23341891
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2015-2020 GMC Canyon | All Terrain, Base, Denali, SL, SLE, SLT | 4 Cyl 2.5 L GAS, 4 Cyl 2.8 L DIESEL, 6 Cyl 3.6 L GAS
View related parts
GMC Canyon Caliper, Passenger Side Part Number: 84737986
$104.36 MSRP: $247.70
You Save: $143.34 (58%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper, Wheel Brake Cylinder/Caliper; Brake Caliper
- Position: Passenger Side
- Replaces: 23341892, 23249390
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2015-2020 GMC Canyon | All Terrain, Base, Denali, SL, SLE, SLT | 4 Cyl 2.5 L GAS, 4 Cyl 2.8 L DIESEL, 6 Cyl 3.6 L GAS
View related parts
GMC Canyon Caliper Assembly, Rear Passenger Side Part Number: 13537066
$65.65 MSRP: $126.89
You Save: $61.24 (49%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper Assembly-Rear Brake (W/O Brake Pads & Bracket); Brake Caliper; Caliper; Caliper, Wheel Brake Cylinder/Caliper
- Position: Rear Passenger Side
- Replaces: 13528632
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2023 GMC Canyon | AT4, AT4X, Denali, Elevation | 4 Cyl 2.7 L GAS
View related parts
GMC Canyon Caliper Assembly, Rear Driver Side Part Number: 13537065
$65.65 MSRP: $126.89
You Save: $61.24 (49%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper Assembly-Rear Brake (W/O Brake Pads & Bracket); Brake Caliper; Caliper; Caliper, Wheel Brake Cylinder/Caliper
- Position: Rear Driver Side
- Replaces: 13528631
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2023 GMC Canyon | AT4, AT4X, Denali, Elevation | 4 Cyl 2.7 L GAS
View related parts
GMC Canyon Caliper Assembly, Rear Passenger Side Part Number: 84309162
$47.77 MSRP: $85.30
You Save: $37.53 (44%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper Assembly-Rear Brake (W/O Brake Pads & Bracket; Brake Caliper; Caliper; Caliper, Wheel Brake Cylinder/Caliper
- Position: Rear Passenger Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2021-2022 GMC Canyon | AT4, Denali, Elevation, Elevation Standard | 4 Cyl 2.5 L GAS, 4 Cyl 2.8 L DIESEL, 6 Cyl 3.6 L GAS
View related parts
GMC Canyon Caliper Assembly, Rear Driver Side Part Number: 84309161
$47.77 MSRP: $85.30
You Save: $37.53 (44%)
ADD TO CART
Product Specifications
- Other Name: Caliper Assembly-Rear Brake (W/O Brake Pads & Bracket; Brake Caliper; Caliper; Caliper, Wheel Brake Cylinder/Caliper
- Position: Rear Driver Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2021-2022 GMC Canyon | AT4, Denali, Elevation, Elevation Standard | 4 Cyl 2.5 L GAS, 4 Cyl 2.8 L DIESEL, 6 Cyl 3.6 L GAS
View related parts
GMC Canyon Caliper Assembly Part Number: 13542336
$91.85 MSRP: $164.02
You Save: $72.17 (44%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper Assembly-Front Brake (W/O Brake Pads & Bracket); Caliper; Caliper, Wheel Brake Cylinder/Caliper
- Replaces: 13539800, 13546092
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2021-2022 GMC Canyon | AT4, Denali, Elevation, Elevation Standard | 4 Cyl 2.5 L GAS, 4 Cyl 2.8 L DIESEL, 6 Cyl 3.6 L GAS
View related parts
GMC Canyon Caliper Assembly Part Number: 13539801
$69.82 MSRP: $124.68
You Save: $54.86 (44%)
ADD TO CART
Product Specifications
- Other Name: Caliper Assembly-Front Brake (W/O Brake Pads & Bracket); Brake Caliper; Caliper; Caliper, Wheel Brake Cylinder/Caliper
- Position: Front
- Replaced by: 13546091
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2021-2022 GMC Canyon | AT4, Denali, Elevation, Elevation Standard | 4 Cyl 2.5 L GAS, 4 Cyl 2.8 L DIESEL, 6 Cyl 3.6 L GAS
View related parts
GMC Canyon Overhaul Kit Part Number: 89040313
Product Specifications
- Other Name: Caliper Kit, Front Brake; Brake Caliper Repair Kit; Disc Brake Hardware Kit; Caliper Kit, Wheel Brake Cylinder/Caliper
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2004-2008 GMC Canyon | SL, SLE, SLT, WT, Z71 Fleet, Z71 SL, Z71 SLE, Z85 SL, Z85 SLE | 4 Cyl 2.8 L GAS, 4 Cyl 2.9 L GAS, 5 Cyl 3.5 L GAS, 5 Cyl 3.7 L GAS
View related parts
GMC Canyon Caliper Part Number: 89040312
Product Specifications
- Other Name: Caliper, Wheel Brake Cylinder/Caliper; Brake Caliper
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2004-2008 GMC Canyon | SL, SLE, SLT, WT, Z71 Fleet, Z71 SL, Z71 SLE, Z85 SL, Z85 SLE | 4 Cyl 2.8 L GAS, 4 Cyl 2.9 L GAS, 5 Cyl 3.5 L GAS, 5 Cyl 3.7 L GAS
View related parts
GMC Canyon Caliper Part Number: 89040311
Product Specifications
- Other Name: Caliper, Wheel Brake Cylinder/Caliper; Brake Caliper
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2004-2008 GMC Canyon | SL, SLE, SLT, WT, Z71 Fleet, Z71 SL, Z71 SLE, Z85 SL, Z85 SLE | 4 Cyl 2.8 L GAS, 4 Cyl 2.9 L GAS, 5 Cyl 3.5 L GAS, 5 Cyl 3.7 L GAS
View related parts
GMC Canyon Caliper, Passenger Side Part Number: 87837860
$123.41 MSRP: $221.36
You Save: $97.95 (45%)
Product Specifications
- Other Name: Caliper Assembly-Front Brake (W/O Brake Pads & Bracket); Caliper, Wheel Brake Cylinder/Caliper
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2023 GMC Canyon | AT4, AT4X, Denali, Elevation | 4 Cyl 2.7 L GAS

GMC Canyon Brake Calipers

Want to cut long-term maintenance and repair costs? Choose OEM Brake Calipers. Those parts deliver top durability you can trust. On our site, you'll find a huge catalog of genuine GMC Canyon parts. Prices are unbeatable, so you can keep more in your pocket. Every OEM GMC Canyon Brake Calipers includes a manufacturer's warranty. You can also get an easy return policy that keeps buying risk free. Fast delivery, get your car on the road quickly. It's simple to search, compare, and order. Stop guessing about quality or fit. Order today and save with parts that last.

GMC Canyon Brake Calipers is one of the vital chassis subsystems, which are charged with the task of applying the forces that act on brake pads and cause them to press against the rotors to produce the necessary friction for the process of vehicle stopping. These calipers come in two main types: The type of allowance is also divided into two categories these are: fixed and floating. As for fixed calipers, they move two pistons with the disc and work more effectively, but they are more sensitive to the disc's flaws. The floating calipers, on the other hand work along the diameter of the disc with one piston that acts on the inner brake pad that results to the sliding of the caliper and apply pressure in both sides of the disc. Nevertheless, a significant problem that affects the floating calipers is sticking resulting from one or many factors that cut down the fuel consumption rate, heightened disc heating, and the pad wearing at varying rates. Other designs of brake calipers are also incorporated in the rim brakes of bicycles.

GMC Canyon Brake Calipers Parts and Q&A

Caliper
21998526
Q: How to replace the Brake Calipers on GMC Canyon?
A:
Lift the vehicle into position and support it properly at the beginning of brake caliper replacement. Take the wheel with tire off the vehicle. Replace the brake hose fitting gaskets with new ones during your work. Separate the brake caliper from its brake hose fitting by first taking off the bolt and secondly removing the gaskets then the brake fitting. Place a fitting cap on the hose to maintain the brake fluid supply during replacement. Once raised and supported, you must remove first the brake caliper guide pin bolts and then the brake caliper itself. Install the brake caliper at first and make sure to put the brake caliper guide pin bolts into place while tightening them to 64Nm (47 lb ft). Insert fresh brake hose gaskets when connecting the brake hose fitting bolt and gaskets to the brake hose fitting. Fix the brake hose assembly to the caliper and wrench-tighten the fitting bolt to 40 Nm (30 lb ft). After bleeding the brake lines you will put on the tire wheel unit.
Caliper
89040311
Q: How to Service and Repair Brake Calipers on GMC Canyon?
A:
Before servicing the brake caliper you need to drain all brake fluid out of the caliper unit. Never put your fingers before a Piston during compressed air use because the outcome can harm you severely. During brake caliper removal you may experience damage to the Piston which needs replacement by a new one. Hang the brake caliper in a safe device then wedge in a timber part before placing a shop towel over it. Compressed filtered air without lubricate helps you take out the brake caliper pistons. Position the taken Piston back into the caliper. Then use a small wood block and a c-clamp with compressed air to force the Piston halfway inside. Place another block of wood ahead of the final Piston and repeat the air application. Push out three pistons from each caliper barrel and afterward two Piston seals without using metal tools. Disconnect the bleeder valve components from the caliper housing and cleanse them all with denatured alcohol before drying them under compressed air filtration. Replace smooth caliper bores either with new pistons or a new caliper before installing unharmed boots back into place. Discard brake caliper debris by cleaning the parts with denatured alcohol before air drying them using compressed lubricated air. Apply brake fluid sparingly onto the Piston dust seal as you place the Piston seal and strut spring using the boot seal installer (J 45863). Put the Piston in place only when it stands flat and straight. Press down the Piston using wood as a buffer and then take away the wooden tool when installation is complete. At last install the Piston dust seal using a driver handle and boot seal installer. Install the bleeder valve and tighten it to 19 nm (14 ft. Lbs.) before covering it with its cap.