Menu
×
Search Bar
Search by Part Number, Part Name, or Vehicle
My Garage
Cart
Help Center Contact Us
Make sure this part fits

GM 10359973
Inner Boot, Front

2006-2017 GM

Customer Questions & Expert Answers (7)
GM 10359973 Inner Boot, Front
GM 10359973 Inner Boot, Front
GM 10359973 Inner Boot, Front
GM 10359973 Inner Boot, Front
  • Part Description
    Boot Kit, Front Wheel Drive Axle Shaft; CV Boot
  • Position
    Front
  • Manufacturer
    General Motors
Make sure this part fits
$33.28 MSRP: $81.20
You Save: $47.92 (60%)
1
ADD TO CART

  • 10359973 Inner Boot, Front is Ref No. 5 in the diagram below

    2010 GMC Terrain Inner Boot, Front Diagram for 10359973
    The diagram listed above is for your reference. View diagram for your vehicle

    Related Parts for 10359973

  • Vehicle Fitment

    Year Make Model Trim Engine
    2010-2017 Chevrolet EquinoxL, LS, LT, LTZ, Premier4 Cyl 2.4 L FLEX, 4 Cyl 2.4 L GAS
    2006-2011 Chevrolet HHRLS, LS Panel, LT, LT Panel, SS, SS Panel4 Cyl 2.0 L GAS, 4 Cyl 2.2 L FLEX, 4 Cyl 2.2 L GAS, 4 Cyl 2.4 L FLEX, 4 Cyl 2.4 L GAS
    2010-2017 GMC TerrainDenali, SL, SLE, SLT4 Cyl 2.4 L FLEX, 4 Cyl 2.4 L GAS
    Warning: California's Proposition 65

  • Customer Questions & Expert Answers

    Q:
    Is this 10359973 designed for my car? Posted by ChevyPartsGiant Specialist
    A:
    Please Select Your Vehicle model to see if part number 10359973 is suitable before ordering.
    Posted by ChevyPartsGiant Specialist
    Q:
    How to replace the front CV Boot and CV Joint on the drive shaft inner joint on GMC Terrain? Posted by Customer
    A:
    Start by removing the wheel drive shaft from your vehicle before replacing its front inner joint and boot assembly. Set the wheel drive shaft bar inside a soft-cushioned vise. First remove the boot retaining clamp from the tripod housing boot with a flat-bladed tool before using side cutters to remove the boot clamp from the wheel drive shaft boot. Start by separating the tripod housing from the wheel drive shaft before removing the retaining clip and the tripod spider that's fitted onto the wheel drive shaft. Check the wheel drive shaft internal joint for damage as well as signs of too much wear after removing the boot from the shaft. Fasten the boot onto the wheel drive shaft before installing the tripot spider assembly on the wheel drive shaft so it rests against the shoulder. Insert the retaining ring into the wheel drive shaft before filling the seal with half of the kit grease and the remaining grease into the tripod housing. The tripod housing should be positioned onto the wheel drive shaft followed by installing boot clamp on both tripot housing boot and wheel drive boot spaces. To secure the boot clamp properly use the J 35910 - Drive Axle Seal Clamp Pliers together with a breaker bar, torque wrench, or ratchet. First adjust the clamp to create a 2.15 mm (0.085 in) wide gap and then finalize the clamp at 1.9 mm (0.070 in). Use circular motion to spread tripot joint grease between applications before the permanent reinstallation of the wheel drive shaft.
    Posted by ChevyPartsGiant Specialist
    Q:
    What should be done after compressing the retaining ring into the groove for the 2010 Chevrolet Equinox? Posted by Customer
    A:
    Install the inner CV joint, ensuring it just touches the inner retaining ring.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar CV Boot
    Q:
    What should be done with the old boot clamp for the 2009 Chevrolet HHR? Posted by Customer
    A:
    Discard the boot clamp from the boot and the wheel drive shaft with side cutters, and replace it with new clamps.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar CV Boot
    Q:
    What is the next step after removing the tripot housing for the 2007 Chevrolet HHR? Posted by Customer
    A:
    Take out the retaining ring from the groove on the wheel drive shaft bar and remove the spider assembly, followed by the seal from the wheel drive shaft bar.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar CV Boot
    Q:
    How do you close the boot clamp securely for the 2008 Chevrolet HHR? Posted by Customer
    A:
    Use the CH-48894 Wheel Drive Shaft Boot Clamp Pliers to close the boot clamp securely.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar CV Boot
    Q:
    What is the required distance between the boot edges when installing the CV joint boot and clamp on the CV joint housing for the 2010 GMC Terrain? Posted by Customer
    A:
    The distance should be 88.6 mm (3.50 in).
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar CV Boot
    If you have any questions about this product, please don't hesitate to ask us. We will be happy to help you!

OEM GM Inner Boot, Front 10359973 Designed for Proper Fit and Performance

Original OEM GM parts deliver superior quality and meet all performance standards needed for optimal automotive operation. The authentic part identified by 10359973 Inner Boot, Front is available in the market under the name GM CV Boot. This genuine product has a full warranty coverage from the manufacturer available at all authorized GM dealers throughout the United States. This part 10359973 Inner Boot, Front fits certain Chevrolet Equinox, HHR models, as well as GMC Terrain models.
The original GM component designated by manufacturer part number 10359973 maintains top performance when functioning as the Boot Kit, Front Wheel Drive Axle Shaft; CV Boot unit at its Front. The component 10359973 is constructed from durable material and its dimensions span 7.4 x 5.2 x 3.1 inches while weighing 1.20 Pounds. The Direct Replacement component is ready in New condition to ensure full compatibility with your vehicle system. The part 10359973 has available replacement options. GM manufacturer provides a warranty that ensures reliable operation of this product. The Shipping Policy and Return Policy pages outline complete details regarding shipping procedures and return processes.
If you want to save money in the long run on maintenance and repairs, you should choose OEM products because they're of the top level of durability. Are you on the quest of finding GM parts, our site is worth a visit. We stock an endless selection of high-quality GM components including things like ignition coils all the way through to fan shrouds and all at prices that can not be matched. You have nothing to worry about because all our OEM parts are covered with a manufacturer warranty, which guarantees superior quality and value.