How to replace the Front CV Boot and CV Joint on the Wheel Drive Shaft Outer Joint on 2008 Chevrolet HHR?

To replace the front wheel drive shaft outer joint boot, it is necessary to clamp the drive Axle Shaft in a soft jawed vice carefully, so there won't be the cutting through the inboard boot, which may result in the damage of the sealing surface and the early wear of constant velocity joint. Unscrew the boot clamp from the constant velocity (CV) joint and the boot with the help of a flat-bladed tool first and then apply side cutters to cut through the boot clamp from the boot and the wheel drive shaft . Get rid of the old boot clamps and use new clamps. Next use a block of wood and a hammer to remove the cv join from the wheel drive shaft and take off the boot from the wheel drive shaft in order to look for cracks within the cv join. Examine the outer cv joint for damage and wear. Place the boot on groove of the wheel drive shaft and ensure that it properly seats in the wheel drive shaft. Inject about half the grease from the service kit into the outboard boot and pack the cv joint with the rest of it. Mount cv joint on the wheel drive shaft by using a block of wood and a hammer, mount boot clamp on the boot and the wheel drive shaft connect it to the boot clamp on the boot on the cv joint housing. Make sure the boot clamp is suitably located at the whole circumference of the boot and use the j 35910 drive axle seal clamp pliers to crimp this piece. Check the dimension of the clamp end gap, which should not be more than 2.15 mm (0.85 in), and clasp the boot clamp securely with the ch-48894 wheel drive shaft boot clamp pliers. Post the wheel drive shaft from the bench vise and evenly spread the grease through the outer cv joint by spinning inside about 4 to 5 rotations before fitting the whole drive shaft in the vehicle.

OEM 2008 Chevrolet HHR CV Boot

Axle Boot

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

8 CV Boots found

View related parts
2008 Chevrolet HHR Inner Boot, Front
Part Number: 10359973
$33.28 MSRP: $81.20
You Save: $47.92 (60%)
ADD TO CART
Product Specifications
- Other Name: Boot Kit, Front Wheel Drive Axle Shaft; CV Boot
- Position: Front
- Item Weight: 1.20 Pounds
- Item Dimensions: 7.4 x 5.2 x 3.1 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 10359973
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2008 Chevrolet HHR Submodels:
- LS, LS Panel, LT, LT Panel, SS, SS Panel | 4 Cyl 2.0 L GAS, 4 Cyl 2.2 L FLEX, 4 Cyl 2.2 L GAS, 4 Cyl 2.4 L FLEX, 4 Cyl 2.4 L GAS
View related parts
2008 Chevrolet HHR Boot Kit, Front
Part Number: 10360041
$55.29 MSRP: $87.77
You Save: $32.48 (38%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Boot Kit, Front Wheel Drive Axle Shaft; CV Boot; Outer Boot
- Position: Front
- Item Weight: 1.20 Pounds
- Item Dimensions: 8.9 x 8.5 x 5.1 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 10360041
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2008 Chevrolet HHR Submodels:
- LS, LS Panel, LT, LT Panel, SS, SS Panel | 4 Cyl 2.0 L GAS, 4 Cyl 2.2 L FLEX, 4 Cyl 2.2 L GAS, 4 Cyl 2.4 L FLEX, 4 Cyl 2.4 L GAS
View related parts
2008 Chevrolet HHR Boot Kit, Green Line, Front
Part Number: 25786428
Product Specifications
- Other Name: Boot Kit, Front Wheel Drive Axle Shaft; CV Boot; Inner Boot; Outer Boot; Boots
- Position: Front
- Item Weight: 1.70 Pounds
- Item Dimensions: 6.9 x 6.2 x 6.1 inches
- Condition: New
- Fitment Type: Direct Replacement
- Require Quantity: 2
- SKU: 25786428
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2008 Chevrolet HHR Submodels:
- SS, SS Panel | 4 Cyl 2.0 L GAS
View related parts
2008 Chevrolet HHR Inner Boot, Front
Part Number: 10359813
Product Specifications
- Other Name: Boot Kit, Front Wheel Drive Axle Shaft; CV Boot
- Position: Front
- Item Weight: 1.10 Pounds
- Item Dimensions: 7.3 x 5.1 x 3.1 inches
- Condition: New
- Fitment Type: Direct Replacement
- Require Quantity: 2
- SKU: 10359813
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2008 Chevrolet HHR Submodels:
- LS, LS Panel, LT, LT Panel, SS, SS Panel | 4 Cyl 2.0 L GAS, 4 Cyl 2.2 L FLEX, 4 Cyl 2.2 L GAS, 4 Cyl 2.4 L FLEX, 4 Cyl 2.4 L GAS
View related parts
2008 Chevrolet HHR Boot Kit, Front
Part Number: 10360040
Product Specifications
- Other Name: Boot Kit, Front Wheel Drive Axle Shaft; CV Boot; Outer Boot
- Position: Front
- Item Weight: 1.20 Pounds
- Item Dimensions: 7.1 x 5.1 x 3.1 inches
- Condition: New
- Fitment Type: Direct Replacement
- Require Quantity: 2
- SKU: 10360040
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2008 Chevrolet HHR Submodels:
- LS, LS Panel, LT, LT Panel, SS, SS Panel | 4 Cyl 2.0 L GAS, 4 Cyl 2.2 L FLEX, 4 Cyl 2.2 L GAS, 4 Cyl 2.4 L FLEX, 4 Cyl 2.4 L GAS
View related parts
2008 Chevrolet HHR Outer Boot, Front
Part Number: 19181205
Product Specifications
- Other Name: Boot Kit, Front Wheel Drive Shaft CV Joint; CV Boot; Boot Kit, Front Wheel Drive Axle Shaft
- Position: Front
- Item Weight: 0.40 Pounds
- Item Dimensions: 4.9 x 4.6 x 4.0 inches
- Condition: New
- Fitment Type: Direct Replacement
- Require Quantity: 2
- SKU: 19181205
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2008 Chevrolet HHR Submodels:
- SS, SS Panel | 4 Cyl 2.0 L GAS
View related parts
2008 Chevrolet HHR Boot Kit, Front
Part Number: 22692206
Product Specifications
- Other Name: Boot Kit, Front Wheel Drive Axle Shaft; CV Boot; Inner Boot; Outer Boot; Boots
- Position: Front
- Item Weight: 1.50 Pounds
- Item Dimensions: 6.1 x 4.4 x 4.3 inches
- Condition: New
- Fitment Type: Direct Replacement
- Require Quantity: 2
- SKU: 22692206
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2008 Chevrolet HHR Submodels:
- SS, SS Panel | 4 Cyl 2.0 L GAS
View related parts
2008 Chevrolet HHR Inner Boot, Front
Part Number: 19181204
Product Specifications
- Other Name: Boot Kit, Front Wheel Drive Shaft Tri-Pot Joint; CV Boot; Boot Kit, Front Wheel Drive Axle Shaft
- Position: Front
- Item Weight: 0.50 Pounds
- Item Dimensions: 4.7 x 4.7 x 4.4 inches
- Condition: New
- Fitment Type: Direct Replacement
- Require Quantity: 2
- SKU: 19181204
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2008 Chevrolet HHR Submodels:
- SS, SS Panel | 4 Cyl 2.0 L GAS

2008 Chevrolet HHR CV Boot

With a comprehensive array of OEM 2008 Chevrolet HHR CV Boot, from fuel pumps to door handles, our website is a one-stop-shop for your needs. All our genuine 2008 Chevrolet HHR CV Boot are backed by the manufacturer's warranty and are offered at competitive prices in the market. Rest assured, you can shop with complete confidence.

2008 Chevrolet HHR CV Boot Parts Questions & Experts Answers

Q: How to replace the Front CV Boot and CV Joint on the Wheel Drive Shaft Outer Joint on 2008 Chevrolet HHR?
A: To replace the front wheel drive shaft outer joint boot, it is necessary to clamp the drive Axle Shaft in a soft jawed vice carefully, so there won't be the cutting through the inboard boot, which may result in the damage of the sealing surface and the early wear of constant velocity joint. Unscrew the boot clamp from the constant velocity (CV) joint and the boot with the help of a flat-bladed tool first and then apply side cutters to cut through the boot clamp from the boot and the wheel drive shaft . Get rid of the old boot clamps and use new clamps. Next use a block of wood and a hammer to remove the cv join from the wheel drive shaft and take off the boot from the wheel drive shaft in order to look for cracks within the cv join. Examine the outer cv joint for damage and wear. Place the boot on groove of the wheel drive shaft and ensure that it properly seats in the wheel drive shaft. Inject about half the grease from the service kit into the outboard boot and pack the cv joint with the rest of it. Mount cv joint on the wheel drive shaft by using a block of wood and a hammer, mount boot clamp on the boot and the wheel drive shaft connect it to the boot clamp on the boot on the cv joint housing. Make sure the boot clamp is suitably located at the whole circumference of the boot and use the j 35910 drive axle seal clamp pliers to crimp this piece. Check the dimension of the clamp end gap, which should not be more than 2.15 mm (0.85 in), and clasp the boot clamp securely with the ch-48894 wheel drive shaft boot clamp pliers. Post the wheel drive shaft from the bench vise and evenly spread the grease through the outer cv joint by spinning inside about 4 to 5 rotations before fitting the whole drive shaft in the vehicle.