GM 22692679
Tail Lamp Bulb

Starting the replacement of front fog lamp bulbs requires removal of the front bumper fascia deflector. Disengage the electrical connector tied to the front fog lamp bulb/socket while following the halogen bulb caution warning. First follow the halogen bulb caution instructions before turning the front fog lamp bulb/socket counterclockwise to disgorge it. Remove the bulb/socket from the assembly. The fog lamp bulb/socket needs to be inserted into its opening followed by a clockwise rotation until complete insertion while maintaining attention to the halogen bulb caution. Use the electrical connector to connect both the fog lamp bulb/socket then return the front bumper fascia deflector into position.

The first step for installing a new rear fog lamp bulb requires removal of the rear fog lamp lens through removing its retaining screws. You should turn the bulb counterclockwise before removing it from the rear fog lamp assembly. To perform the installation keep the new bulb facing the rear fog lamp assembly then turn it clockwise. When reinstalling the rear fog lamp lens you must fasten it using the retaining screws which should be tightened to 2 n.m (18 lb in). Check the function of the rear fog lamp as the last part of the process.

The first step to exchange the rear fog lamp bulb requires removal of the rear fog lamp lens by unscrewing its retaining screws. Pull the bulb out from the rear fog lamp assembly by turning it counterclockwise before tucking the bulb clockwise into place. Proceed with careful handling of the halogen bulbs throughout this operation. Installation requires users to place the new bulb into the fog lamp assembly before rotating it clockwise for tight fixing. Reconnect the rear fog lamp lens after you install its retaining screws which you must tighten to 2 n.m (18 lb in). Regular inspection of the rear fog lamp will determine its correct functional state.

Vehicle elevation and support are necessary before replacing the fog lamp bulb on Camaro and Firebird models. Open the entry way located inside the front air deflector on the bumper. Trans Am owners need to remove push pin retainers that exist at the bottom center of their front fascia before continuing. Detaching the electrical connector from the fog lamp will enable the removal of the fog lamp bulb from this connection. Begin with attaching the new bulb to the electrical connector then place the connector back onto the fog lamp. Put push pin retainers back in their proper place at the bottom center of the front fascia for Trans Am vehicles and restore the access door in front bumper air deflector before lowering the vehicle for Camaro and Firebird models.

Start by removing the push-in retainers securing the front flap on the front wheelhouse liner to the fascia. Then bend the flap upwards to obtain access to the fog lamp. You should rotate the fog lamp socket counterclockwise before it will exit from the housing for bulb removal from the socket. Start with inserting a new fog lamp bulb into the socket and reinstall the fog lamp bulb socket into its housing. Install the wheelhouse liner front flap after moving it back into its proper position and fastening its push-in retainers.

The first step to replace old style front fog lamp bulbs requires disconnecting their electrical connector. People need to exercise caution with halogen bulbs when following these instructions. First, rotate the bulb counterclockwise while pulling it straight from the fog lamp assembly. Place the new bulb into the fog lamp component and turn it first in a clockwise direction until secure followed by reattaching the electrical wiring.

A service person should begin by turning off the fog lamp switch followed by carefully removing the bulb from the bottom of the fog lamp assembly using counterclockwise twisting motion and pulling action. The new bulb installation requires inserting it into the bottom part of the fog lamp assembly and twisting it clockwise for lock. Complete the bulb check by switching on the fog lamp control.

In order to replace the rear fog lamp bulb, the first step is to remove the rear fog lamp lens retaining screws . Be careful about halogen bulb safety. Then, twist bulb anti-clockwise and remove from the rear fog lamp assembly. For fitting, push the new bulb into the rear fog lamp assembly and turn clockwise. Secure the retaining screws to 2 n.m (18 lb in) and ultimately, check the operation of the rear fog lamp.

Users should begin the rear fog lamp bulb replacement process by removing the lens through screw removal. The replacement steps require careful handling of halogen bulbs. After removing the retaining screws from the rear fog lamp lens you should proceed to remove the bulb from its assembly by turning it counterclockwise while pulling it out. You must insert the new bulb into the rear fog lamp assembly before securing it by turning the bulb clockwise. Install the rear fog lamp lens through a procedure of reinstalled retaining screws which must be tightened to 2 n.m (18 lb in). The last step involves checking the functioning of the rear fog lamp.

The first step to exchange the rear fog lamp bulb requires removal of the rear fog lamp lens by unscrewing its retaining screws. Pull the bulb out from the rear fog lamp assembly by turning it counterclockwise before tucking the bulb clockwise into place. Proceed with careful handling of the halogen bulbs throughout this operation. Installation requires users to place the new bulb into the fog lamp assembly before rotating it clockwise for tight fixing. Reconnect the rear fog lamp lens after you install its retaining screws which you must tighten to 2 n.m (18 lb in). Regular inspection of the rear fog lamp will determine its correct functional state.

A service person should begin by turning off the fog lamp switch followed by carefully removing the bulb from the bottom of the fog lamp assembly using counterclockwise twisting motion and pulling action. The new bulb installation requires inserting it into the bottom part of the fog lamp assembly and twisting it clockwise for lock. Complete the bulb check by switching on the fog lamp control.

The first step in fog lamp bulb replacement is to disconnect the electrical connector while following the halogen bulb caution in service precautions. The bulb needs counterclockwise twisting before pulling it out from the fog lamp assembly. The installation process starts with inserting the new bulb into the fog lamp while twisting it clockwise for screwing and finishing by reattaching the electrical connector.

To change the rear fog lamp bulb detach the rear fog lamp lens ( remove the retaining screws) first. Then turn the bulb anti-clockwise and take it out from the rear fog lamp assembly. Be careful with halogen bulbs with the process. For installation, fit the new bulb in the rear fog lamp assembly and turn it clockwise to fix. Rear fog lamp lens to reattach it by fixing retaining screws and 2 n.m (18 lb in tightening). Finally, test the functioning of the rear fog lamp for proper operation.

Remove the front bumper fascia deflector.

Disconnect the electrical connector from the front fog lamp bulb, taking care to observe the Halogen Bulb Caution.

Remove the front bumper fascia deflector.

Reinstall the push pin retainers at the bottom center of the front fascia.

First, raise and suitably support the vehicle.

Remove the push pin retainers located at the bottom center of the front fascia.

Insert the rear fog lamp bulb back into the harness socket.

Insert the new fog lamp bulb into the socket.

Place the new fog lamp bulb into the lamp housing and twist it about 1/4 turn clockwise to secure it.

Raise and support the vehicle.

Insert the new bulb into the fog lamp assembly and twist it clockwise to secure it.

First raise and support the vehicle.

Insert the new bulb into the rear fog lamp assembly and twist it clockwise to secure it.

Reinstall the rear fog lamp lens by securing it with the retaining screws, tightening them to 2 N.m (18 lb in).

Twist the bulb counterclockwise and pull it out from the rear fog lamp assembly.

Remove the electrical connector, taking care to observe the Halogen Bulb Caution.

Twist the bulb counterclockwise and pull it out from the fog lamp assembly.

Exercise caution regarding halogen bulbs.

Twist the bulb counterclockwise and pull it out from the fog lamp assembly.

Reconnect the electrical connector.