Make sure this part fits

GM 88965345
Clockspring

2006-2009 GM

Customer Questions & Expert Answers (5)
GM 88965345 Clockspring
GM 88965345 Clockspring
  • Part Description
    Coil, Inflatable Restraint System; Air Bag Clockspring
  • Manufacturer
    General Motors
  • Manufacturer's Notes
    This part is discontinued.
Make sure this part fits
  • Related Parts
  • Product Specifications
  • Vehicle Fitment
  • Customer Questions & Expert Answers
  • Product Specifications

    BrandGenuine GM
    Manufacturer Part Number88965345
    Part DescriptionCoil, Inflatable Restraint System; Air Bag Clockspring
    Item Dimensions9.8 x 6.2 x 5.0 inches
    Item Weight1.80 Pounds
    ConditionNew
    Fitment TypeDirect Replacement
    ManufacturerGeneral Motors
    SKU88965345
    WarrantyThis genuine GM part is guaranteed by GM's factory warranty.
    Shipping & ReturnShipping Policy Return Policy
    Warning: California's Proposition 65
  • Vehicle Fitment

    Year Make Model Trim Engine
    2006-2007 Buick RainierCXL6 Cyl 4.2 L GAS, 8 Cyl 5.3 L GAS
    2006-2009 Chevrolet TrailblazerBase, LS, LT, SS6 Cyl 4.2 L GAS, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L GAS
    2006 Chevrolet Trailblazer EXTLS, LT6 Cyl 4.2 L GAS, 8 Cyl 5.3 L GAS
    2006-2009 GMC EnvoyDenali, SLE, SLT6 Cyl 4.2 L GAS, 8 Cyl 5.3 L GAS
    2006 GMC Envoy XLDenali, SLE, SLT6 Cyl 4.2 L GAS, 8 Cyl 5.3 L GAS
  • Customer Questions & Expert Answers

    Q:
    Is 88965345 compatible with my car? Posted by ChevyPartsGiant Specialist
    A:
    Please Select Your Vehicle model to see if part number 88965345 is suitable before ordering.
    Posted by ChevyPartsGiant Specialist
    Q:
    How to Remove and Replace the Air Bag Clockspring Assembly on GMC Envoy? Posted by Customer
    A:
    The air bag clock spring assembly / spiral cable replacement operation requires disabling the sir system before proceeding. Begin with a center position tilt of the Steering Column before you remove the Steering Wheel from its column. The next step requires you to eliminate both the upper and bottom trim pieces. Check the Steering Column for damage caused by accidents when possible. Pad control enabled steering wheels require the entire inflatable restraint Steering Wheel module coil and wire harness assembly to be removed at once. The coil can be removed by itself when such removal technique is approved. Use a screwdriver to eliminate the wire harness strap alongside possible wire harness assembly detachment. Steer towards the removal of the Steering Wheel module coil after using snap ring pliers on the retaining ring. The installation of the wave washer occurs when required. Insert and position the wave washer carefully along the Steering Shaft assembly block tooth at the 12 o'clock direction. Installation of new inflatable restraint Steering Wheel modules must wait until final installation because their centering tab serves as a pre-installation organizer. Users must verify that their originally used coil maintains proper positioning before further installation steps. Guide the inflatable restraint Steering Wheel module coil to face the horn tower before sliding it onto the Steering Shaft assembly. Use snap ring pliers to install the retaining ring into the race and upper shaft assembly's groove. Then discard the centering tab but ensure the whole retaining ring is seated properly. Put the retaining ring into position using snap ring pliers. Whenever a Steering Wheel has pad control functions you need to add the wire harness assembly. Set the wire harness strap in place before you install upper and lower trim covers as well as the Steering Wheel onto its column. Finally, enable the sir system.
    Posted by ChevyPartsGiant Specialist
    Q:
    What should be done after completing the installation for the 2006 Buick Rainier? Posted by Customer
    A:
    Enable the SIR system afterward.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Air Bag Clockspring
    Q:
    What should be removed after the steering wheel for the 2008 GMC Envoy? Posted by Customer
    A:
    Remove the upper and lower trim covers.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Air Bag Clockspring
    Q:
    What should be done during installation regarding the wave washer for the 2007 GMC Envoy? Posted by Customer
    A:
    If needed, install the wave washer and align the block tooth on the steering shaft assembly to the 12 o'clock position.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Air Bag Clockspring
    If you have any questions about this product, please don't hesitate to ask us. We will be happy to help you!

OEM GM 88965345, Excellent Performance and Perfect Fitment

To ensure reliability, purchase GM part # 88965345 Clockspring. It is sometimes referred to as GM Air Bag Clockspring. Choosing OEM parts is the optimal decision for guaranteeing superior quality and perfect performance. These components undergo stringent quality checks and are carefully constructed to comply with GM's factory specifications, ensuring a smooth installation process.

ChevyPartsGiant.com is a leading supplier of genuine GM parts such as GM 88965345 Clockspring. Our website boasts an extensive inventory of OEM GM parts, available at highly competitive prices in the market. Should you require any new genuine GM parts, rest assured we will deliver them swiftly and efficiently to your doorstep. Furthermore, all our parts come with the assurance of a manufacturer's warranty. For detailed Chevy parts information, click here.
Choose ChevyPartsGiant for discounted prices, exceptional service and fast delivery