GM 84674406
Nameplate

Clean an uncontaminated work space before any body emblem or nameplate installation to prevent adhesive problems. Start by cleaning the installation space using flash naphtha or a combination of 50% isopropyl alcohol and water solution. Afterward, properly dry the area before proceeding. Keep the body area at temperatures between 27 and 41 degrees Celsius (80 to 105 Fahrenheit) while applying heat when needed. Also normalize the item to be installed to 29 to 32 degrees Celsius (80 to 90 Fahrenheit) before heating with care. Take off the shield covering from the emblem. Apply 3-10 pounds of pressure against the molding as you press it against the body part. Next place 0.12mm (0.005 inch) thick clear plastic over the item and use a heavy force to spread 75% of the adhesive film. Firmly apply emblems in their right position to make sure the adhesive connects well with the vehicle surface.

Clear the work space from dust and dirt before working with the adhesive backing. Use a cleaning solution like flash naphtha or an isopropyl alcohol and water mix to wipe the marking area before making it completely dry. Control area temperatures at 27-41°C (80-105°F) while warming up the body and keep the item to mount at 29-32°C (80-90°F) using heat carefully. Ready the surface for application when you take off the protection. Place appliques against the body using 3-10 lb of pressure followed by 0.12 mm (0.005 in) thick clear plastic taped over the item to wet about 75 percent of the adhesive under high pressure. To mount emblems properly, apply them at the center section while using foam padding to shield them from damage.

Hand roll the emblem/nameplate to ensure proper adhesion and inspect for bonding before removing the tape from the area around the endgate emblem.

Maintain a temperature range of 27-41°C (80-105°F) in the body area, applying heat if necessary.

Remove the upper grille baffle.

Hand roll the emblem/nameplate and inspect for bonding before removing the tape from the area around the door emblem.

A minimum of 21°C (70°F).

A minimum of 21°C (70°F).

Secure the emblem by installing the nuts on the back side and tightening them to 2.5 Nm (22 lb.in.).

Apply tape to the area surrounding the emblem for protection and alignment.

Carefully remove the emblem/nameplate from the door surface with a plastic, flat-bladed tool.

Clean the door surface with varnish makers and painters (VMP) naptha.

Use a heat gun (J 25070) positioned 152 mm (6.0 in) from the surface to heat the emblem/nameplate in a circular motion for about 30 seconds.

A minimum of 21°C (70°F) without touching the adhesive backing of the emblem/nameplate.

Use a heat gun (J 25070) positioned 152 mm (6.0 in) from the surface to heat the emblem/nameplate in a circular motion for about 30 seconds.

Warm the door surface with the heat gun (J 25070) to a minimum of 21°C (70°F) without touching the adhesive backing of the emblem/nameplate.

Clean them with 3M(TM) scotch brite molding adhesive remover disk 3M(TM) P/N 07501 or equivalent, then clean the door surface using varnish makers and painters (VMP) naphtha.

Remove the backing from the front end of the emblem/nameplate and press it onto the door panel surface while continuing to remove the backing.

Take off the nuts that secure the emblem to the radiator grille, and then detach the emblem from the radiator grille.

Eliminate any adhesive residue using the 3M(TM) ScotchBrite molding adhesive remover disk (3M(TM) P/N 07501).

Clean the area with varnish makers and painters (VMP) naptha.

Carefully remove it with a plastic, flat-bladed tool and eliminate any adhesive residue using the 3M adhesive remover.

Carefully remove the emblem/nameplate with a plastic, flat-bladed tool.

Carefully remove it with a plastic, flat-bladed tool.

Secure the emblem by installing the nuts on the back side and tightening them to 2.5 N.m (22 lb in).

The environment should be free of dust or dirt, and the mounting area should be cleaned with a suitable solvent.

Use 3M(R) P/N 07501 or equivalent.

Remove the tape from around the emblem/nameplate.

A plastic, flat-bladed tool.

Use a small flat-bladed tool to release the retaining clips located on the rear of the emblem.

Attach the emblem to the grille, ensuring to follow the Fastener Notice.

Hand roll the emblem/nameplate to ensure proper adhesion and inspect for bonding.

Peel the backing from the adhesive tape, align the emblem/nameplate with the masking tape or magnetic strip, and firmly press it into place for 30 seconds to ensure proper adhesion before removing the masking tape or magnetic strip.

Take off the nuts that secure the emblem to the radiator grille and then remove the emblem from the radiator grille.

Place the emblem back onto the radiator grille and ensure to follow fastener caution to avoid vehicle damage.

The body area should be within a temperature range of 27-41°C (80-105°F), heating if necessary.

Apply it to the back of the emblem/nameplate and press it in place.

Remove the radiator grille.

Remove the protective liner from the back of the molding or emblem and apply pressure to ensure the adhesive makes contact.

First, remove the upper grille baffle.

A small flat-bladed tool.

Align the emblem with the openings on the grille and push it rearward until the retaining clips are fully seated.

Separate and remove the emblem from the grille.

A minimum of 21°C (70°F).

Ensure it is free from dust.

Secure the nuts to the back side of the grille emblem, tightening them to 2.5 N.m (22 lb in).

Maintain a temperature range of 27-41°C (80-105°F) in the body area, applying heat if necessary.