Make sure this part fits

GM 15889807
Hub Assembly, Rear

2004-2008 GM

Customer Questions & Expert Answers (8)
GM 15889807 Hub Assembly, Rear
  • Part Description
    Bearing Assembly-Rear Wheel; Wheel Hub & Bearing Assembly; Axle Bearing.
  • Position
    Rear
  • Replaces
    22723647, 22706424
  • Manufacturer
    General Motors
  • Manufacturer's Notes
    This part is discontinued.
Make sure this part fits
  • Vehicle Fitment

    Year Make Model Trim Engine
    2006-2008 Chevrolet HHRLS, LS Panel, LT, LT Panel, SS4 Cyl 2.0 L GAS, 4 Cyl 2.2 L GAS, 4 Cyl 2.4 L GAS
    2004-2007 Chevrolet MalibuBase, LS, LT, LTZ, Maxx, Maxx LS, Maxx LT, Maxx LTZ, Maxx SS, SS4 Cyl 2.2 L GAS, 6 Cyl 3.5 L GAS, 6 Cyl 3.9 L GAS
    2005-2008 Pontiac G6Base, GT, GTP, GXP4 Cyl 2.4 L GAS, 6 Cyl 3.5 L GAS, 6 Cyl 3.6 L GAS, 6 Cyl 3.9 L GAS
    Warning: California's Proposition 65
  • Customer Questions & Expert Answers

    Q:
    Is this 15889807 designed for my car? Posted by ChevyPartsGiant Specialist
    A:
    Please Select Your Vehicle model to see if part number 15889807 is suitable before ordering.
    Posted by ChevyPartsGiant Specialist
    Q:
    What should be reconnected after installing the wheel bearing/hub assembly for the 2006 Chevrolet Malibu? Posted by Customer
    A:
    The stabilizer link bolt at the knuckle and the electrical connector to the wheel speed sensor if equipped with ABS.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Wheel Bearing
    Q:
    What should be removed after the tire and wheel assembly for the 2006 Chevrolet Malibu? Posted by Customer
    A:
    Take off the wheel drive shaft nut and the brake rotor.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Wheel Bearing
    Q:
    What should be done if it is equipped with ABS for the 2007 Chevrolet Malibu? Posted by Customer
    A:
    Disconnect the electrical connector from the wheel speed sensor and remove the wheel speed sensor connector from the bracket by depressing the locking tabs.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Wheel Bearing
    Q:
    What is the torque specification for the wheel bearing/hub mounting nuts for the 2008 Chevrolet HHR? Posted by Customer
    A:
    Tighten them to 45 N.m (33 lb ft), then use the J 45059 to rotate the mounting nuts an additional 30 degrees.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Wheel Bearing
    Q:
    What needs to be removed to access the wheel bearing/hub nuts for the 2005 Chevrolet Malibu? Posted by Customer
    A:
    Remove the stabilizer link bolt at the knuckle and position the stabilizer link out of the way.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Wheel Bearing
    Q:
    What should be avoided when removing the wheel bearing mounting bolts for the 2004 Chevrolet Malibu? Posted by Customer
    A:
    Take care to avoid contact with the outer constant velocity boot seal to prevent damage.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Wheel Bearing
    Q:
    What are the final steps after reassembling the components for the 2007 Chevrolet Malibu? Posted by Customer
    A:
    Reinstall the brake rotor, the tire and wheel assembly, and lower the vehicle.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Wheel Bearing
    If you have any questions about this product, please don't hesitate to ask us. We will be happy to help you!

OEM GM Hub Assembly, Rear 15889807 Designed for Proper Fit and Performance

Original OEM GM parts deliver superior quality and meet all performance standards needed for optimal automotive operation. The authentic part identified by 15889807 Hub Assembly, Rear is available in the market under the name GM Pinion Bearing, Wheel Bearing. This genuine product has a full warranty coverage from the manufacturer available at all authorized GM dealers throughout the United States. This part 15889807 Hub Assembly, Rear fits certain Chevrolet Malibu, HHR models, as well as Pontiac G6 models.
The original GM component designated by manufacturer part number 15889807 maintains top performance when functioning as the Bearing Assembly-Rear Wheel; Wheel Hub & Bearing Assembly; Axle Bearing. unit at its Rear. The component 15889807 is constructed from durable material and its dimensions span 7.3 x 6.8 x 8.8 inches while weighing 7.90 Pounds. The Direct Replacement component is ready in New condition to ensure full compatibility with your vehicle system. This component receives the designation of Rear Hub; Hub & Bearing; Bearing, Rear Wheel. The part 15889807 has available replacement options 22723647, 22706424. Each vehicle needs 2 units of the part marked as SKU 15889807. GM manufacturer provides a warranty that ensures reliable operation of this product. The Shipping Policy and Return Policy pages outline complete details regarding shipping procedures and return processes.
If you want to save money in the long run on maintenance and repairs, you should choose OEM products because they're of the top level of durability. Are you on the quest of finding GM parts, our site is worth a visit. We stock an endless selection of high-quality GM components including things like ignition coils all the way through to fan shrouds and all at prices that can not be matched. You have nothing to worry about because all our OEM parts are covered with a manufacturer warranty, which guarantees superior quality and value.