Make sure this part fits

GM 15166766
Rear Seal

1994-2005 GM

Customer Questions & Expert Answers (15)
GM 15166766 Rear Seal
  • Part Description
    Seal, Hood Panel
  • Position
    Rear
  • Replaces
    15647848
  • Manufacturer
    General Motors
  • Manufacturer's Notes
    This part is discontinued.
Make sure this part fits
  • Vehicle Fitment

    Year Make Model Trim Engine
    1995-2005 Chevrolet BlazerBase, LS, LT, Trailblazer, Xtreme, ZR26 Cyl 4.3 L GAS
    1994-2004 Chevrolet S10Base, LS, SS, Xtreme, ZR2, ZR54 Cyl 2.2 L FLEX, 4 Cyl 2.2 L GAS, 6 Cyl 4.3 L GAS
    1995-2001 GMC JimmyBase, Diamond Edition, Envoy, SL, SLE, SLS, SLT6 Cyl 4.3 L GAS
    1994-2004 GMC SonomaSL, SLE, SLS4 Cyl 2.2 L FLEX, 4 Cyl 2.2 L GAS, 6 Cyl 4.3 L GAS
    1996-2004 Oldsmobile BravadaBase6 Cyl 4.2 L GAS, 6 Cyl 4.3 L GAS
    Warning: California's Proposition 65
  • Customer Questions & Expert Answers

    Q:
    Is this 15166766 designed for my car? Posted by ChevyPartsGiant Specialist
    A:
    Please Select Your Vehicle model to see if part number 15166766 is suitable before ordering.
    Posted by ChevyPartsGiant Specialist
    Q:
    What is the first step to replace the front door weatherstrip (Drip Channel) for the 2005 Chevrolet Blazer? Posted by Customer
    A:
    Open the door and remove the weatherstrip drip channel.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Weather Strip
    Q:
    How do you remove the existing weatherstrip from the door opening for the 2004 Chevrolet Blazer? Posted by Customer
    A:
    Gently pull it away from the pinch weld flange.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Weather Strip
    Q:
    What is the final step after installing the weatherstrip for the 2005 Chevrolet Blazer? Posted by Customer
    A:
    Reinstall the sunroof window.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Weather Strip
    Q:
    How do you install the new weatherstrip for the 2002 Chevrolet S10? Posted by Customer
    A:
    Open the liftgate window and push the new weatherstrip onto the pinch-weld flange, starting with the pre-formed corner at either upper corner of the liftgate window opening.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Weather Strip
    Q:
    What tool is used to remove the existing weatherstrip for the 2002 Chevrolet S10? Posted by Customer
    A:
    The Door Trim Pad Clip Remover (J 38778) is used.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Weather Strip
    Q:
    Where should the weatherstrip seal be positioned for the 2002 Chevrolet S10? Posted by Customer
    A:
    Position the weatherstrip seal at the upper rear corner of the door opening against the body side outer panel.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Weather Strip
    Q:
    How do you secure the new seal for the 2004 Chevrolet S10? Posted by Customer
    A:
    Install the screws to secure the seal to the cowl, tightening them to 1.9 N.m (17 lb in).
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Weather Strip
    Q:
    What type of adhesive should be applied during installation for the 2003 Chevrolet S10? Posted by Customer
    A:
    Apply black, non-corrosive silicone adhesive under the entire outside edge of the new seal.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Weather Strip
    Q:
    Where do you position the weatherstrip for installation for the 2001 GMC Jimmy? Posted by Customer
    A:
    Position the pre-formed corner of the weatherstrip in the upper rear corner of the door opening.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Weather Strip
    Q:
    What is the first step to replace the outer door weatherstrip for the 2000 GMC Jimmy? Posted by Customer
    A:
    Open the window and remove the outer door weatherstrip from the door.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Weather Strip
    Q:
    How do you start replacing the rear side door window weatherstrip for the 2000 GMC Jimmy? Posted by Customer
    A:
    First, open the rear side door window and remove the weatherstrip by starting at the butt joint and pulling it from the window opening.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Weather Strip
    Q:
    What should you do after removing the front seal for the 2004 GMC Sonoma? Posted by Customer
    A:
    Position the sunroof in the vent position and finish removing the seal from the rear of the mainframe.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Weather Strip
    Q:
    Where should the seam of the weatherstrip be positioned during installation for the 2004 GMC Sonoma? Posted by Customer
    A:
    The seam should be positioned at the center of the rear edge of the sunroof window.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Weather Strip
    Q:
    What should you do after removing the old seal for the 2003 GMC Sonoma? Posted by Customer
    A:
    Position the new seal assembly to the hood and press it into place until it is fully seated.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Weather Strip
    If you have any questions about this product, please don't hesitate to ask us. We will be happy to help you!

OEM GM Rear Seal 15166766 Designed for Proper Fit and Performance

Original OEM GM parts deliver superior quality and meet all performance standards needed for optimal automotive operation. The authentic part identified by 15166766 Rear Seal is available in the market under the name GM Weather Strip. This genuine product has a full warranty coverage from the manufacturer available at all authorized GM dealers throughout the United States. This part 15166766 Rear Seal fits certain Chevrolet S10, Blazer models, as well as GMC Sonoma, Jimmy. Additionally, it is compatible with Oldsmobile Bravada models.
The original GM component designated by manufacturer part number 15166766 maintains top performance when functioning as the Seal, Hood Panel unit at its Rear. The component 15166766 is constructed from durable material and its dimensions span 18.2 x 17.5 x 5.5 inches while weighing 1.80 Pounds. The Direct Replacement component is ready in New condition to ensure full compatibility with your vehicle system. This component receives the designation of Cowl Top Panel Seal; Cowl Grille Seal. The part 15166766 has available replacement options 15647848. GM manufacturer provides a warranty that ensures reliable operation of this product. The Shipping Policy and Return Policy pages outline complete details regarding shipping procedures and return processes.
If you want to save money in the long run on maintenance and repairs, you should choose OEM products because they're of the top level of durability. Are you on the quest of finding GM parts, our site is worth a visit. We stock an endless selection of high-quality GM components including things like ignition coils all the way through to fan shrouds and all at prices that can not be matched. You have nothing to worry about because all our OEM parts are covered with a manufacturer warranty, which guarantees superior quality and value.