Menu
×
Search Bar
Search by Part Number, Part Name, or Vehicle
My Garage
Cart
Help Center Contact Us
Make sure this part fits

GM 12371989
Water Pump

1987-2005 GM

Customer Questions & Expert Answers (26)
GM 12371989 Water Pump
  • Part Description
    Pump Kit, Water
  • Manufacturer
    General Motors
  • Manufacturer's Notes
    This part is discontinued.
Make sure this part fits

  • 12371989 Water Pump is Ref No. 9 in the diagram below

    2004 Chevy Monte Carlo Water Pump Diagram for 12371989
    The diagram listed above is for your reference. View diagram for your vehicle

    Related Parts for 12371989

  • Vehicle Fitment

    Year Make Model Trim Engine
    1994-2005, 1987-1989 Buick CenturyCustom, Estate Wagon, Limited, Special, Special Edition4 Cyl 2.2 L GAS, 4 Cyl 2.5 L GAS, 6 Cyl 2.8 L GAS, 6 Cyl 3.1 L GAS, 6 Cyl 3.3 L GAS, 6 Cyl 3.8 L GAS
    1988-1996 Buick RegalCustom, Gran Sport, Limited6 Cyl 2.8 L GAS, 6 Cyl 3.1 L GAS
    2002 Buick RendezvousCX, CX Plus, CXL, CXL Plus6 Cyl 3.4 L GAS
    1994-1998 Buick SkylarkCustom, Gran Sport, Limited, Olympic Gold Edition6 Cyl 3.1 L GAS
    1987-1988 Cadillac CimarronBase6 Cyl 2.8 L GAS
    1987-1996 Chevrolet BerettaBase, GT, GTZ, Indianapolis 500 Pace Car, Z266 Cyl 2.8 L GAS, 6 Cyl 3.1 L GAS
    1987-1994 Chevrolet CavalierBase, CS, RS, Z246 Cyl 2.8 L GAS, 6 Cyl 3.1 L GAS
    1987-1990 Chevrolet CelebrityBase, CL, Estate, Eurosport6 Cyl 2.8 L GAS, 6 Cyl 3.1 L GAS
    1987-1996 Chevrolet CorsicaBase, LT, LTZ6 Cyl 2.8 L GAS, 6 Cyl 3.1 L GAS
    2000-2005 Chevrolet ImpalaBase6 Cyl 3.4 L GAS
    View More
    Warning: California's Proposition 65

  • Customer Questions & Expert Answers

    Q:
    Is this 12371989 designed for my car? Posted by ChevyPartsGiant Specialist
    A:
    Please Select Your Vehicle model to see if part number 12371989 is suitable before ordering.
    Posted by ChevyPartsGiant Specialist
    Q:
    How to service and repair a water pump on Chevrolet Lumina? Posted by Customer
    A:
    The first step in servicing the Water Pump requires draining the cooling system. Start by unpacking the Drive Belt guard and then slightly loosen the Water Pump Pulley bolts before you detach the Drive Belt. Detach the pulley bolts of the Water Pump and uninstall the Water Pump itself along with the Water Pump Gasket . Prepare the Water Pump surfaces thoroughly before placing the gasket and the Water Pump on the engine. Apply the Water Pump bolts and tighten them to 10 newton meters or 89 inch pounds torque. Put the Water Pump Pulley in place and bolt it down while snug at 25 nm (18 ft. Lbs.). Put the belt back in place while tightening both Water Pump Pulley bolts. Place the Drive Belt guard back in its position. Stop by filling the cooling system then check for fluid leakage.
    Posted by ChevyPartsGiant Specialist
    Q:
    How to replace a water pump on Chevrolet Venture? Posted by Customer
    A:
    To replace the Water Pump, you would need first drain the cooling system so that the coolant level is below the Water Pump level. Then, you remove the Drive Belt guard and loosen the Water Pump Pulley bolts before removing the Drive Belt. Then turn the Water Pump pulleys and bolts to unscrew them and take out pulley bolts and pulley in the Water Pump. Do not forget to clean the mating surfaces if you remove the Water Pump Gasket. For installation, we first place a new Water Pump Gasket then proceed with placing the Water Pump following the fastener notice in service precautions. Secure the Water Pump with 10 nm 89 inch lbs engaged bolts, then loosen the Water Pump Pulley Drive Belt makes sense. Then, replace the Water Pump Pulley bolts using 25 nm (18 inch lbs) and re-installing the Drive Belt guard. The cooling system should be filled and we should look for drips.
    Posted by ChevyPartsGiant Specialist
    Q:
    What is the final step in the process for the 2003 Buick Century? Posted by Customer
    A:
    Fill the cooling system.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Water Pump
    Q:
    What should be done after removing the drive belt guard for the 2002 Buick Century? Posted by Customer
    A:
    Loosen the water pump pulley bolts, then remove the drive belt and the water pump pulley bolts before taking off the water pump pulley itself.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Water Pump
    Q:
    What is the next step after removing the drive belt for the 2000 Buick Century? Posted by Customer
    A:
    Remove the water pump pulley bolts and then the water pump pulley itself.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Water Pump
    Q:
    What should be reinstalled after the water pump pulley for the 2004 Buick Century? Posted by Customer
    A:
    Reinstall the drive belt.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Water Pump
    Q:
    What should be done before installing the new gasket and water pump for the 2001 Buick Century? Posted by Customer
    A:
    Clean the water pump mating surfaces.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Water Pump
    Q:
    What should be done before installing the new water pump for the 2002 Chevrolet Malibu? Posted by Customer
    A:
    Clean the mating surfaces of the water pump.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Water Pump
    Q:
    What is the next step after repositioning the power steering pump for the 2005 Chevrolet Impala? Posted by Customer
    A:
    Remove the water pump bolts and the water pump.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Water Pump
    Q:
    What should be removed after the water pump pulley for the 2000 Chevrolet Malibu? Posted by Customer
    A:
    Remove the water pump attaching bolts and then the water pump, followed by the water pump gasket.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Water Pump
    Q:
    What is the next step after securing the holding tool for the 2004 Chevrolet Malibu? Posted by Customer
    A:
    Remove the three inner water pump sprocket to water pump bolts and the two water pump assembly bolts, followed by the rear two water pump assembly bolts.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Water Pump
    Q:
    How should the water pump bolts be installed for the 2000 Chevrolet Impala? Posted by Customer
    A:
    Install the water pump bolts, tightening them to 10 Nm (89 inch lbs.).
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Water Pump
    Q:
    What are the final steps after reinstalling the water pump pulley for the 2000 Chevrolet Monte Carlo? Posted by Customer
    A:
    Reinstall the power steering pump, the drive belt, fill the cooling system, and inspect for leaks.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Water Pump
    Q:
    What should be done before installing the new water pump for the 2003 Chevrolet Malibu? Posted by Customer
    A:
    Clean the water pump mating surfaces.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Water Pump
    Q:
    What is the first step to replace the water pump for the 2002 Chevrolet Monte Carlo? Posted by Customer
    A:
    First, drain the cooling system and remove the drive belt guard.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Water Pump
    Q:
    What is the next step after installing the water pump bolts for the 2005 Chevrolet Monte Carlo? Posted by Customer
    A:
    Install the water pump pulley and its bolts, tightening them to 25 Nm (18 inch lbs.).
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Water Pump
    Q:
    What should be done after draining the cooling system for the 2004 Chevrolet Impala? Posted by Customer
    A:
    Loosen the water pump pulley bolts and remove the drive belt.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Water Pump
    Q:
    What is the first step to replace the water pump in a 3.4L engine for the 2003 Chevrolet Monte Carlo? Posted by Customer
    A:
    First, drain the cooling system.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Water Pump
    Q:
    What are the final steps after installing the water pump and pulley for the 2001 Chevrolet Impala? Posted by Customer
    A:
    Reinstall the drive belt and the drive belt guard, then fill the cooling system and inspect for leaks.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Water Pump
    Q:
    What should be done before installing the new water pump for the 2004 Chevrolet Monte Carlo? Posted by Customer
    A:
    Clean the mating surfaces for the water pump gasket.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Water Pump
    Q:
    What is the torque specification for securing the water pump pulley bolts for the 2001 Chevrolet Venture? Posted by Customer
    A:
    Secure the water pump pulley bolts to 25 Nm (18 inch lbs.).
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Water Pump
    Q:
    What is the procedure for installing the new water pump for the 2001 Chevrolet Malibu? Posted by Customer
    A:
    Install the water pump gasket and pump, then install the water pump bolts and tighten them to 10 Nm (89 inch lbs.).
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Water Pump
    Q:
    What needs to be taken out before removing the pump for the 2000 Chevrolet Venture? Posted by Customer
    A:
    Take out the auxiliary coolant pump retaining clips.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Water Pump
    Q:
    What should be done after removing the drive belt for the 2002 Chevrolet Venture? Posted by Customer
    A:
    Remove the water pump pulley bolts and the water pump pulley itself.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Water Pump
    Q:
    What should be done after installing the water pump bolts for the 2005 Chevrolet Venture? Posted by Customer
    A:
    Loosely install the water pump pulley and the drive belt.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Water Pump
    If you have any questions about this product, please don't hesitate to ask us. We will be happy to help you!

OEM GM Water Pump 12371989 Designed for Proper Fit and Performance

Original OEM GM parts deliver superior quality and meet all performance standards needed for optimal automotive operation. The authentic part identified by 12371989 Water Pump is available in the market under the name GM Water Pump. This genuine product has a full warranty coverage from the manufacturer available at all authorized GM dealers throughout the United States. This part 12371989 Water Pump fits certain Chevrolet Malibu, Impala, Cavalier models, as well as Cadillac Cimarron. Additionally, it is compatible with Buick Regal, Skylark, Century and Pontiac Grand Prix, Grand Am, 6000 models.
The original GM component designated by manufacturer part number 12371989 maintains top performance when functioning as the Pump Kit, Water unit. The component 12371989 is constructed from durable material and its dimensions span 6.9 x 6.4 x 5.4 inches while weighing 3.20 Pounds. The Direct Replacement component is ready in New condition to ensure full compatibility with your vehicle system. This component receives the designation of Water Pump Assembly; Pump; Pump Kit, Engine Coolant; Pump, Engine Coolant. The part 12371989 has available replacement options. GM manufacturer provides a warranty that ensures reliable operation of this product. The Shipping Policy and Return Policy pages outline complete details regarding shipping procedures and return processes.
If you want to save money in the long run on maintenance and repairs, you should choose OEM products because they're of the top level of durability. Are you on the quest of finding GM parts, our site is worth a visit. We stock an endless selection of high-quality GM components including things like ignition coils all the way through to fan shrouds and all at prices that can not be matched. You have nothing to worry about because all our OEM parts are covered with a manufacturer warranty, which guarantees superior quality and value.