GM 13503102
Fuel Pump Relay, Gray; Green

The first step to replace a power distribution relay requires removing the electrical center cover but locating the relay while observing its orientation then securing the electrical center before and after the replacement. The J 43244 Relay Puller Pliers (J 43244) should be placed against opposing relay corners before extracting it straight through the electrical center terminals because pliers and flat-bladed tools may damage the electrical center. Place the new relay into the same opening from which you removed the original device followed by the installation of the electrical center cover.

Service operations for the Fuel Pump Relay must begin with ignition off and the removal of the rear seat cushion. Push the tabs away from the fuse relay center cover before taking out the Fuel Pump Relay from its location. To complete the installation reinstalle the Fuel Pump Relay into the fuse relay center followed by putting on the rear fuse relay center cover then return the rear seat cushion.

The first step to service the fuel pump relay includes turning off the ignition followed by removing the under hood electrical center cover. After removing the power supply from the ignition switch proceed to disconnect the fuel pump relay. Install the fuel pump relay first then replace the under hood electrical center cover for the procedure. Finally, turn the ignition ON.

The first step to service the fuel pump relay includes turning off the ignition followed by removing the under hood electrical center cover. After removing the power supply from the ignition switch proceed to disconnect the fuel pump relay. Install the fuel pump relay first then replace the under hood electrical center cover for the procedure. Finally, turn the ignition ON.

Service of the Fuel Pump Relay starts with turning off the ignition before unbearably the negative Battery Cable. You should start by taking the underhood bec cover off and subsequently removing the Fuel Pump Relay from the underhood bec. To complete the installation process reconnect the negative Battery Cable after reattaching both the underhood bec cover and inserting the Fuel Pump Relay into the underhood bec.

Before servicing the Daytime Running Lamp Relay begin by opening the electrical center cover to locate it through the relays/fuses diagram. Extract the relay from its place in the underhood electrical center. Study the cover's relays/fuses diagram to find the relay position before placing it back into the electrical center during installation. Then install the cover back into its original position. Open the vehicle's ignition and put the gear lever into a position that's out of park while your assistant checks the front area to verify DRL operation.

Service of the Fuel Pump Relay begins by unsnapping the fuse block assembly cover then removing the Fuel Pump Relay. Install the Fuel Pump Relay by putting it back into its original position before placing on the fuse block assembly cover that had been removed from the assembly.

Service of the Fuel Pump Relay begins by unsnapping the fuse block assembly cover then removing the Fuel Pump Relay. Install the Fuel Pump Relay by putting it back into its original position before placing on the fuse block assembly cover that had been removed from the assembly.

Start by opening the hood then removing protection from the underhood fuse block before working on replacing the DRL Relay. You need to remove the DRL relay from its position in the underhood fuse block. The procedure begins with repositioning the DRL relay into the underhood fuse block. After this install the protective cover onto the underhood fuse block before finishing with hood closure.

The first task for replacing the power distribution relay requires removal of the electrical center cover followed by relay location identification while making a record of its alignment then properly securing the electrical center to prevent wire or terminal damage. The J 43244 Relay Puller Pliers (J 43244) should be positioned against opposing relay corners before removing it from electrical center terminals because pliers or flat-bladed tools can harm the electrical center. Replace the new relay into the same slot where you removed the original one and after that replace the electrical center cover.

Service of the Daytime Running Lamp Relay begins with hood opening and hood support followed by removing protection from the underhood fuse block. First extract the DRL relay from the underhood fuse block. Install the DRL relay into the underhood fuse block while also placing the protective cover back then close the hood.

Before servicing the Daytime Running Lamp Relay begin by opening the electrical center cover to locate it through the relays/fuses diagram. Extract the relay from its place in the underhood electrical center. Study the cover's relays/fuses diagram to find the relay position before placing it back into the electrical center during installation. Then install the cover back into its original position. Open the vehicle's ignition and put the gear lever into a position that's out of park while your assistant checks the front area to verify DRL operation.

The Fuel Pump Relay service process begins with removing the negative Battery Cable. The Fuel Pump Relay can be found after underhood electrical center cover removal in the location identified on the electrical center cover. After the Fuel Pump Relay installation put it in its original position and replace the underhood electrical center cover before reconnecting the negative Battery Cable.

The left side knee bolster needs removal before starting to service the Daytime Running Lamp Relay. Start by removing the cover off the block to reach the DRL daytime running lights relay before you disconnect it from the block. Installation requires placing the relay into the block then adding the cover to the DRL daytime running lights relay and finally securing the left side knee bolster.

Start by removing the left knee bolster before attempting Daytime Running Lamps (DRL) relay replacement. Access the DRL relay by removing the block cover then remove the relay from its block position. Follow these replacement steps: insert the relay into the block before you secure the cover and finish by reinstalled the left knee bolster.

The service of the fuel pump relay requires remove of the relay center cover followed by pulling upward to extract the fuel pump relay. The fuel pump relay must be inserted into its socket within the relay center before you install the center cover.

Service of the fuel pump relay requires the removal step by step of the relay center cover. Two movements are needed to remove the fuel pump relay: first you should take the relay cover off and then pull upward on the relay. To install the relay position it into the matching socket inside the relay center before placing the relay center cover.

Begin by uninstalling the cover from the electrical center before accessing the relay. When finding the relay mark its current position then safely place the electrical center before wires or terminals become damaged. The Relay Puller Pliers (J 43244) should be placed on opposing corners of the relay to extract it directly from the electrical center terminals since pliers or flat-bladed tools might harm the electrical center. When installing a new relay it should replace the previous relay in its original installation position before securing everything with the electrical center cover.

Service of the Fuel Pump Relay begins with disconnecting the negative Battery Cable. First disconnect the underhood electrical center cover and then remove the Fuel Pump Relay located according to the marked position on the cover. Install the Fuel Pump Relay into its electrical center cover position followed by underhood electrical cover replacement before reconnecting the negative cable.

Start the service of the Daytime Running Lamp Relay by taking out the instrument panel driver knee bolster panel. Untighten the three bolts connecting the relay center and the bracket to the inner/outer brackets of the instrument panel driver knee bolster before removing them both from their mounting sites. Start by taking out the DRL relay from its position within the relay center. First connect the DRL relay to the relay center and reinstall both components back onto the inner and outer brackets of the instrument panel driver knee bolster. Three bolts need to be carefully installed to fasten the relay center with the bracket while you should tighten them to 4 N.m (35 lb in). Reinstall the instrument panel driver knee bolster panel as the concluding step.

The first step for replacing the Power Distribution Relay involves finding the relay then unfastening all screw connectors that stabilize it along with any connector position assurance (CPA) devices or secondary lock components. The user should exercise special care when disconnecting the relay from the wiring harness particularly if fasteners or tape are used for attachment. You should disconnect the relay from its position on the wire harness connector. The installation process starts with attaching the relay to wire harness connector and following by adding secondary locks and CPA devices and ending with original fastening devices or tape.

The process to replace a Power Distribution Relay attached to the wire harness begins by finding the relay before unfastening its location while disassembling CPA devices and secondary lock systems. To detach the relay from its wires ensure extra care because fasteners together with tape may be securing the components. You need to disconnect the relay from its position inside the wire harness connector. Follow this procedure to install the relay: connect it to the wire harness connector followed by CPA devices and secondary locks installation before reinstalling the original fasteners or tape.

To service the fuel pump relay first, turn OFF the ignition and remove under hood electrical center cover. Then remove the fuel pump relay. To install replace the fuel pump relay in position then reinstall under the hood electrical center cover.

The process starts by opening the electrical center cover while using the relays/fuses diagram to find the DRL relay. Extract the relay from the underhood electrical center. Look at the diagram to determine the correct relay location then mount the relay in the electrical center. Afterward, reinstall the cover . Begin vehicle operation with gear out of "P" before having an assistant check out front to verify DRL function.

Before servicing the Daytime Running Lamp Relay begin by opening the electrical center cover to locate it through the relays/fuses diagram. Extract the relay from its place in the underhood electrical center. Study the cover's relays/fuses diagram to find the relay position before placing it back into the electrical center during installation. Then install the cover back into its original position. Open the vehicle's ignition and put the gear lever into a position that's out of park while your assistant checks the front area to verify DRL operation.

Service of the Fuel Pump Relay starts by removing the cover from the left underhood electrical center. First remove the cover from the left underhood electrical center before pulling the fuel pump relay upward. The procedure for installation requires you to insert the relay into the relay center socket before reattaching the left underhood electrical center cover.

Service of the Fuel Pump Relay starts by removing the cover from the left underhood electrical center. First remove the cover from the left underhood electrical center before pulling the fuel pump relay upward. The procedure for installation requires you to insert the relay into the relay center socket before reattaching the left underhood electrical center cover.

The first step to replace a Power Distribution Relay which connects to the wire harness begins with using the Master Electrical Component List to identify its location in the vehicle. The following steps should be used for relay replacement beginning with fastener removal before extracting CPA devices and secondary locks while paying attention to avoid damaging the relay while disconnecting it from the wiring harness. Reconnect the new relay to its wire harness connector after separating it then reinstall CPA devices and secondary locks followed by replacing original fasteners and tape for securing the relay.

The Fuel Pump Relay service process begins with removing the negative Battery Cable. The Fuel Pump Relay can be found after underhood electrical center cover removal in the location identified on the electrical center cover. After the Fuel Pump Relay installation put it in its original position and replace the underhood electrical center cover before reconnecting the negative Battery Cable.

Before servicing the Daytime Running Lamp Relay begin by opening the electrical center cover to locate it through the relays/fuses diagram. Extract the relay from its place in the underhood electrical center. Study the cover's relays/fuses diagram to find the relay position before placing it back into the electrical center during installation. Then install the cover back into its original position. Open the vehicle's ignition and put the gear lever into a position that's out of park while your assistant checks the front area to verify DRL operation.

Service of the Fuel Pump Relay starts by removing the cover from the left underhood electrical center. First remove the cover from the left underhood electrical center before pulling the fuel pump relay upward. The procedure for installation requires you to insert the relay into the relay center socket before reattaching the left underhood electrical center cover.

Start the Fuel Pump Relay servicing by disconnecting the negative Battery Cable. You should start by removing the underhood electrical center cover before removing the Fuel Pump Relay from its designated location shown on the cover. Install the Fuel Pump Relay in its original position then replace the underhood electrical cover before returning the negative Battery Cable connection.

The left side knee bolster needs to be uninstalled before servicing the Daytime Running Lamp Relay. The installation process begins with removing the cover that allows access to the DRL daytime running lights relay which then needs removal from its block. The installation sequence follows placement of the relay into the block then cover reinstallation for the DRL daytime running lights relay followed by bolted left knee bolster reattachment.

The process starts by opening the electrical center cover while using the relays/fuses diagram to find the DRL relay. Extract the relay from the underhood electrical center. Look at the diagram to determine the correct relay location then mount the relay in the electrical center. Afterward, reinstall the cover . Begin vehicle operation with gear out of "P" before having an assistant check out front to verify DRL function.

Use the J 43244 Relay Puller Pliers (J 43244) to position the tool on opposing corners of the relay and pull it straight out from the electrical center terminals.

Exercise caution to avoid damage when detaching the relay from the wire harness connector.

Install the new relay in the same position as the old one and then reinstall the electrical center cover.

First, remove the electrical center cover.

Reinstall any CPA devices or secondary locks and secure the relay using the original fasteners or tape.

Position the tool on opposing corners of the relay and pull it straight out from the electrical center terminals.

Use the Relay Puller Pliers (J43244).

Using them may damage the electrical center.

Exercise caution if the relay is secured by fasteners or tape.

Gently separate the relay from the wire harness connector.

First, remove the electrical center cover and locate the relay, ensuring to note its orientation and secure the electrical center to avoid stress on the wires or terminals.

Disconnect the negative battery cable.

Place the protective cover back onto the rear fuse block.

Place the protective cover back onto the rear fuse block.

Place the reverse lamp relay back into the rear fuse block.

Put the rear seat cushion back in place.

Take out any connector position assurance (CPA) devices or secondary locks.

Use the Master Electrical Component List to locate the relay.

First, locate the relay and remove any fasteners securing it.

First, remove the electrical center cover and locate the relay, ensuring to note its orientation and secure the electrical center to avoid stress on the wires or terminals.

Take out the fuel pump relay.

Exercise caution to avoid damage when detaching the relay from the wire harness connector.

Finally, secure the relay using the fasteners or tape that originally held it in place.

Reattach any CPA devices or secondary locks.

Reinstall the electrical center cover.

Use the Relay Puller Pliers (J 43244) to position the tool on opposing corners of the relay.

Take out any connector position assurance (CPA) devices or secondary locks.

Using them may damage the electrical center.

Place the fuel pump relay back in position and reinstall the under hood electrical center cover.

Reinstall the electrical center cover.

Reinstall the electrical center cover.

Identify the electrical center where it exists, ensuring to note the orientation of the relay.

Exercise caution to avoid damage when detaching the relay from the wiring harness.

First, pull the relay from the relay center and remove it from the convenience center.

Reinstall the under hood electrical center cover.

Install the new relay in the same position as the one removed.

Use the Master Electrical Component List for guidance on its position in the vehicle.

Remove the underhood electrical center cover.

First, remove the electrical center cover and locate the relay, ensuring to note its orientation and secure the electrical center to avoid stress on the wires or terminals.

Exercise caution when detaching the relay from the wire harness connector, especially if it is secured by fasteners or tape.

Avoid using pliers or a flat-bladed tool, as they may damage the electrical center.

Secure the relay using the original fasteners or tape that held it in place.

Reinstall the electrical center cover.

Exercise caution to avoid damage when detaching the relay from the wire harness connector.

Connect the fuel pump relay electrical connector.

Push the relay back into the relay center and then install it into the convenience center.

Place the fuel pump relay back in its designated location.

Use the Master Electrical Component List for guidance on its position in the vehicle.

Remove the underhood electrical center cover.

Exercise caution when detaching the relay from the wire harness connector, especially if it is secured by fasteners or tape.

First, locate the relay and remove any fasteners securing it in place, along with any connector position assurance (CPA) devices or secondary locks.

Install the new relay in the same position as the one removed.

Exercise caution when detaching the relay from the wiring harness, especially if it is secured by fasteners or tape.

Install any CPA devices or secondary locks.

Take out the three bolts that secure the relay center and the bracket to the inner and outer brackets of the instrument panel driver knee bolster.