Other Name: Relay, Main Wiring Junction And Fuse Block; Rear Window Defroster Relay; Multi Purpose Relay; Window Relay; Lock Relay; Relay; Relay, Headlamp/Fog Lamp/Turn Signal
Fits the following Chevrolet Models:
Aveo | 2004-2011 | Base, LS, LT, Special Value | 4 Cyl 1.6 L GAS
Aveo5 | 2007-2011 | LS, LT, Special Value | 4 Cyl 1.6 L GAS
Other Name: Relay Assembly, Stop Lamp Switch *Light Gray; Multi Purpose Relay; ABS Relay; Relay; Relay, Air Suspension And Inflator Unit; Relay, Voltage And Glow Plug
Replaces: 12135010, 12193605
Fits the following Chevrolet Models:
Beretta | 1993-1994 | Base, GT, GTZ, Z26 | 4 Cyl 2.2 L GAS, 4 Cyl 2.3 L GAS, 6 Cyl 3.1 L GAS
Cavalier | 1993-1994 | RS, VL, Z24 | 4 Cyl 2.2 L GAS, 6 Cyl 3.1 L GAS
Corsica | 1993-1994 | Base, LT | 4 Cyl 2.2 L GAS, 6 Cyl 3.1 L GAS
Uplander | 2005-2008 | Base, LS, LT | 6 Cyl 3.5 L GAS, 6 Cyl 3.9 L FLEX, 6 Cyl 3.9 L GAS
Venture | 2002-2005 | Base, LS, LT, Plus, Value, Warner Bros. | 6 Cyl 3.4 L GAS
Other Name: Relay, Main Wiring Junction And Fuse Block; Multi Purpose Relay; Relay, Engine Air Cooling(Electrical); Relay, Voltage And Glow Plug; Relay, Engine Vacuum Pump
Fits the following Chevrolet Models:
Cruze | 2011-2016 | Diesel, Eco, L, LS, LT, LTZ, Premier | 4 Cyl 1.4 L GAS, 4 Cyl 1.8 L FLEX, 4 Cyl 1.8 L GAS, 4 Cyl 2.0 L DIESEL
Cruze Limited | 2016 | Eco, L, LS, LT, LTZ | 4 Cyl 1.4 L GAS, 4 Cyl 1.8 L FLEX, 4 Cyl 1.8 L GAS
Malibu | 2013-2015 | Eco, LS, LT, LTZ | 4 Cyl 2.0 L GAS, 4 Cyl 2.4 L MILD HYBRID EV-GAS (MHEV), 4 Cyl 2.5 L GAS
Malibu Limited | 2016 | LS, LT, LTZ | 4 Cyl 2.5 L GAS
Other Name: Relay, Headlamp/Fog Lamp/Turn Signal; Multi Purpose Relay; Relay: Trans Oil Pump, Eng Air Cooling(Elec), Headlamp Washer/Wiper, Voltage & Glow Plug, Eng Vacuum Pump, Starter Motor
Replaces: 13500119
Fits the following Chevrolet Models:
Equinox | 2010-2024 | L, LS, LT, LTZ, Premier, RS | 4 Cyl 1.5 L GAS, 4 Cyl 1.6 L DIESEL, 4 Cyl 2.0 L GAS, 4 Cyl 2.4 L FLEX, 4 Cyl 2.4 L GAS, 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS
Impala | 2014-2016 | Eco, LS, LT, LTZ | 4 Cyl 2.4 L MILD HYBRID EV-GAS (MHEV), 4 Cyl 2.5 L FLEX, 4 Cyl 2.5 L GAS, 6 Cyl 3.6 L BI-FUEL, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS
Malibu | 2013-2015 | Eco, LS, LT, LTZ | 4 Cyl 2.0 L GAS, 4 Cyl 2.4 L MILD HYBRID EV-GAS (MHEV), 4 Cyl 2.5 L GAS
Malibu Limited | 2016 | LS, LT, LTZ | 4 Cyl 2.5 L GAS
Q: How to replace the relay within the electrical center on Chevrolet Equinox?
A: Begin by uninstalling the cover from the electrical center before accessing the relay. When finding the relay mark its current position then safely place the electrical center before wires or terminals become damaged. The Relay Puller Pliers (J 43244) should be placed on opposing corners of the relay to extract it directly from the electrical center terminals since pliers or flat-bladed tools might harm the electrical center. When installing a new relay it should replace the previous relay in its original installation position before securing everything with the electrical center cover.
Q: How to replace the relay within the electrical center on Chevrolet Impala?
A: Before replacing a relay within the electrical center start by removing the electrical center cover to identify the relay position and note its orientation for new relay installation and any notch placement when the relay has notches. Protecting the electrical center from damage is essential because straining wires and terminals can occur during insecure conditions. The J 43244 tool must be positioned on opposing corners of the relay before gently pulling the relay straight out from the electrical center terminals to avoid damaging the electrical center and pliers or flat bladed tools should be avoided. Manual removal of the relay leaves its installation spot available for replacing the new relay before securing the electrical center cover.
Q: How to replace the power distribution relay within the electrical center on Chevrolet Malibu?
A: The replacement process for the electrical center power distribution relay begins with removal of its cover. Identify the relay position while checking its orientation before installing the electrical center to protect wire terminals from damage. Instert the Relay Puller Pliers (J 43244) between opposing relay corners before drawing it straight out from electrical center terminals to avoid damaging the electrical center with flat-bladed tools or pliers. Move the electrical center cover away before you place the new relay precisely where the removed one was located and you can reinstall the cover.