Other Name: Switch, Back Up Lamp; Back Up Light Switch; Back-Up Switch
Fits the following Chevrolet Models:
Astro | 1985-1989 | Base, CL, CS, LT | 4 Cyl 2.5 L GAS, 6 Cyl 4.3 L GAS
Camaro | 1993-2002, 1984-1989 | Base, Berlinetta, Indianapolis 500 Pace Car, Iroc-Z, LT, RS, Sport, Z28, Z28 SS | 4 Cyl 2.5 L GAS, 6 Cyl 2.8 L GAS, 6 Cyl 3.4 L GAS, 6 Cyl 3.8 L GAS, 8 Cyl 5.0 L GAS, 8 Cyl 5.7 L GAS
Chevette | 1984-1987 | Base, CS | 4 Cyl 1.6 L GAS
Corvette | 1997-2004 | 50th Anniversary Edition, 50th Anniversary Edition Pace Car, Base, Indianapolis 500 Pace Car, Z06 | 8 Cyl 5.7 L GAS
S10 | 1984-1996 | Baja, Base, Durango, EL, LS, Sport, Tahoe | 4 Cyl 1.9 L GAS, 4 Cyl 2.0 L GAS, 4 Cyl 2.2 L DIESEL, 4 Cyl 2.2 L GAS, 4 Cyl 2.5 L GAS, 6 Cyl 2.8 L GAS, 6 Cyl 4.3 L GAS
S10 Blazer | 1984-1993 | Base, High Country, Sport, Tahoe, Tahoe LT | 4 Cyl 1.9 L GAS, 4 Cyl 2.0 L GAS, 4 Cyl 2.2 L DIESEL, 4 Cyl 2.5 L GAS, 6 Cyl 2.8 L GAS, 6 Cyl 4.3 L GAS
Q: How to replace the Back Up Light Switch on Chevrolet Colorado?
A: Start by raising the vehicle before proceeding with replacement of the back up lamp switch. First disconnect the back up lamp switch electrical connector at the pigtail before opening the tie strap that secures the pigtail to the transmission. Extract the back up lamp switch while also removing its aluminum washer. Insert a NEW aluminum washer into the transmission case when installing the back up lamp switch while tightening it to 44 Nm (32 ft. lbs.). Lower the vehicle only after securing the pigtail to the transmission through the tie strap and reconnecting the back up lamp switch electrical connector at the pigtail.
Q: How to replace the Back Up Light Switch on Chevrolet Camaro?
A: First, raise and appropriately hold the vehicle. idar Disconnect the back up lamp switch electrical connector and remove the back up lamp switch. Before installation, apply a pipe sealant with Teflon on the back up lamp switch threads with GM P/N 1052080 or its equivalent. Install the back up lamp switch and get it tightened to 38 Nm (28 ft. lbs.). Last but not least, connect the back up lamp switch electrical connector and let the vehicle down.
Q: How to Change the Back Up Light Switch on a Chevrolet SSR?
A: In order to replace the back up lamp switch, first lift the vehicle. Remove the back lamp switch electrical connector, remove the retaining bolt for the back up lamp electrical connector bracket and take out the back up lamp switch. If for installation, install the back up lamp switch and tighten it 20 nm (14 ft. Lbs.). In turn, position the retaining bracket on the transmission and fasten the retaining bolt by the bolt is to tighten to 10 nm (88 inch lbs.). Lastly, reconnect the switch for the back up lights and bring the vehicle down.