OEM 2004 Chevrolet Corvette Front Cross-Member

Front Engine Cross Member
  • Select Vehicle by Model
  • Select Vehicle by VIN
Select Vehicle by Model
Make
Model
Year
or
Select Vehicle by VIN
For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

1 Front Cross-Member found

  • 2004 Chevy Corvette Front Cross-Member - 10319530
    2004 Chevy Corvette Front Cross-Member Diagram - 10319530
    View related parts
    Product Specifications
    • Other Name: Crossmember; Crossmember, Front Frame Cross Member
    • Position: Front
    • Replaces: 10266822, 10312076
    • Item Weight: 38.10 Pounds
    • Item Dimensions: 39.5 x 26.0 x 8.2 inches
    • Condition: New
    • Fitment Type: Direct Replacement
    • SKU: 10319530
    • Warranty: This genuine part is guaranteed by GM's factory warranty.
    More Info
    Fits the following 2004 Chevrolet Corvette Submodels:
    • 50th Anniversary Edition, 50th Anniversary Edition Pace Car, Base, Indianapolis 500 Pace Car, Z06 | 8 Cyl 5.7 L GAS

2004 Chevrolet Corvette Front Cross-Member

With a comprehensive array of OEM 2004 Chevrolet Corvette Front Cross-Member, from fuel pumps to door handles, our website is a one-stop-shop for your needs. All our genuine 2004 Chevrolet Corvette Front Cross-Member are backed by the manufacturer's warranty and are offered at competitive prices in the market. Rest assured, you can shop with complete confidence.

2004 Chevrolet Corvette Front Cross-Member Parts Questions & Experts Answers

  • Q: How to replace the Front Cross-Member on 2004 Chevrolet Corvette?
    A: In order to replace the front suspension crossmember, firstly, one should take off the generator from the accessory mounting bracket, and then the washer pump/reservoir. Service the accelerator control switch by replacement with a new one. Support the engine by the j 41803 (Engine Support Fixture) and j 28467-b (Universal Engine Support Fixture), once more, raise and support the vehicle. Remove the tire and wheel assemblies, and the steering linkage outer tie rod end stud nuts. In case present, remove the Shock Absorber solenoid electrical connector and the real-time damping (RTD) sensor connections. Eliminate stabilizer shaft, disengage intermediate shaft, lower coupling of steering gear, eliminate bolts from electronic brake control module/brake pressure modulator-valve (EBCM/BPMV) bracket, and support and relocate ebcm/bpmv and bracket from center cross member. Take off the power steering gear mounting bolts and power steering fluid cooler off the crossmember and lift the power steering gear off the crossmember. To take away the transverse spring out from the vehicle, use the j 33432-a (Transverse Spring Compressor) to remove the bolts on the level Shock Absorber from the lower control arms and the lower control arms from the crossmember. Place a transmission jack under the crossmember, and take out the engine mount lower nuts. Unplug the wheel speed sensor wiring harness, the electrical harness from clips of the momentary crossmember and the brake pipe from clips of the momentary crossmember. Unscrew the nuts of the crossmember that mount onto it and remove the crossmember from the vehicle. For installation lift the crossmember to the vehicle by matching the dowel pins to the frame rails as well as the engine mount studs. Replace new crossmember mounting nuts and tighten it at 110 nm (81 ft. Lbs ). Mount the engine lower nuts, tighten the wheel speed sensor wiring harness retaining clips, and attach the electrical harness and brake pipe onto the clip of the crossmember. Select and install the transverse spring using the j 33432-a with the lower Control Arm and shock absorbers; tighten the lower mounting nuts of the shock absorbers to 28 nm (21 ft. Lbs). Mount the power steering gear by securing it in place with the mounting bolts to 100 nm (74 ft. Lbs.), then the bolts for the brake pressure modulator valve bracket. Restoring the connection of the intermediate side to the steering gear, installing the steering linkage outtie rod ends, and joining the rtd sensor links and Shock Absorber solenoid el. Connecter when available. To complete the steering system assembly on the vehicle, install the stabilizer shaft, tire and wheel assemblies, as well as lower the vehicle. Remove the j 41803 and j 28467-b from the engine and reinstall the generator and washer pump/reservoir. Reconnect the engine coolant temperature switch electrical connector and the front headlamp electrical connector, tighten the negative Battery Cable to 15 nm (11 ft. Lbs.) and carry out the vehicle front end alignment.

Related 2004 Chevrolet Corvette Parts