How to Replace the Front Brake Disc (JH6, JH9) on 2010 Chevrolet Express 3500?

Use jack and supports to lift the vehicle and uncover the wheel components first before replacing the front Brake Disc (JH6, JH9). Drive a screwdriver through the Brake Disc vanes to stop the disc spinning before removing the hub extension but retaining its marks to the hub. Install aawl to separate the bolts from the hub extension bolts. You can use a non-metallic mallet in a tapping motion to loosen the hub extension where needed. After marking the hub-disc position attach a c-clamp over the caliper to force pistons in before taking off the clamp. Wedge the brake caliper in place using mechanics wire to prevent brake fluid tube harm from accidental damage. Use mechanics wire to sustain the brake caliper assembly as you disconnect its bolts from the caliper bracket and remove it along with the bracket from the wheel assembly. Before pulling off the disc use an oil penetrant to clean surfaces and apply force through two bolts sized m10 x 1.5 to push the disc away from the hub when the disc retaining washers prove difficult to remove. Clean all rust from the hub flange area using j-42450-a. Also remove debris from both contact surfaces. Place the disc back in its proper position and then add the caliper and its support hardware. Clean the caliper bracket bolts from old adhesive then treat their threads with threadlocker part number gm 12345493 (Canadian 10953488). Apply threadlocker to two-thirds of the bolt and allow it to set for 10 minutes before assembly. Safely add the front wheel hub extension if equipped. Then secure all caliper bracket bolts at 300 nm (221 lb ft) prior to installing the wheel hub extension. Put on the tire and wheel components before you apply the brake pedal at one-third of its range until the pedal pressure achieves solidity in multiple instances. After filling the master cylinder with new brake fluid, you should let the pad and disc pairing form a smooth surface by operating the brakes.

OEM 2010 Chevrolet Express 3500 Brake Disc

Disc Rotor

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

6 Brake Discs found

View related parts
2010 Chevrolet Express 3500 Rotor
Part Number: 15712803
$141.83 MSRP: $250.60
You Save: $108.77 (44%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Rotor, Front And Rear Wheel Brake; Brake Rotor
- Position: Rear
- Item Weight: 30.00 Pounds
- Item Dimensions: 16.5 x 17.0 x 6.2 inches
- Condition: New
- Fitment Type: Direct Replacement
- Require Quantity: 2
- SKU: 15712803
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2010 Chevrolet Express 3500 Submodels:
- Base, LS, LT | 8 Cyl 4.8 L FLEX, 8 Cyl 4.8 L GAS, 8 Cyl 6.0 L CNG, 8 Cyl 6.0 L FLEX, 8 Cyl 6.0 L GAS, 8 Cyl 6.6 L DIESEL
View related parts
2010 Chevrolet Express 3500 Rotor
Part Number: 15712801
$96.36 MSRP: $180.93
You Save: $84.57 (47%)
ADD TO CART
Product Specifications
- Other Name: Rotor, Front And Rear Wheel Brake; Brake Rotor
- Position: Rear
- Item Weight: 13.40 Pounds
- Item Dimensions: 15.9 x 16.6 x 5.6 inches
- Condition: New
- Fitment Type: Direct Replacement
- Require Quantity: 2
- SKU: 15712801
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2010 Chevrolet Express 3500 Submodels:
- Base, LS, LT | 8 Cyl 4.8 L FLEX, 8 Cyl 4.8 L GAS, 8 Cyl 6.0 L FLEX, 8 Cyl 6.0 L GAS, 8 Cyl 6.6 L DIESEL
View related parts
2010 Chevrolet Express 3500 Rotor, Front
Part Number: 15942198
$181.17 MSRP: $324.96
You Save: $143.79 (45%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Rotor-Front Brake; Disc Brake Hardware Kit; Brake Rotor; Rotor, Front And Rear Wheel Brake
- Position: Front
- Replaces: 18060654
- Item Weight: 30.20 Pounds
- Item Dimensions: 14.2 x 13.8 x 3.9 inches
- Condition: New
- Fitment Type: Direct Replacement
- Require Quantity: 2
- SKU: 15942198
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2010 Chevrolet Express 3500 Submodels:
- Base, LS, LT | 4 Cyl 2.8 L DIESEL, 6 Cyl 4.3 L FLEX, 6 Cyl 4.3 L GAS, 8 Cyl 4.8 L FLEX, 8 Cyl 4.8 L GAS, 8 Cyl 6.0 L CNG, 8 Cyl 6.0 L FLEX, 8 Cyl 6.0 L GAS, 8 Cyl 6.6 L DIESEL, 8 Cyl 6.6 L GAS
View related parts
2010 Chevrolet Express 3500 Rotor, Rear
Part Number: 15127537
$145.40 MSRP: $260.76
You Save: $115.36 (45%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Rotor-Rear Brake; Brake Rotor; Rotor, Front And Rear Wheel Brake
- Position: Rear
- Item Weight: 24.20 Pounds
- Item Dimensions: 16.5 x 16.2 x 5.6 inches
- Condition: New
- Fitment Type: Direct Replacement
- Require Quantity: 2
- SKU: 15127537
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2010 Chevrolet Express 3500 Submodels:
- Base, LS, LT | 4 Cyl 2.8 L DIESEL, 6 Cyl 4.3 L FLEX, 6 Cyl 4.3 L GAS, 8 Cyl 4.8 L FLEX, 8 Cyl 4.8 L GAS, 8 Cyl 6.0 L CNG, 8 Cyl 6.0 L FLEX, 8 Cyl 6.0 L GAS, 8 Cyl 6.6 L DIESEL, 8 Cyl 6.6 L GAS
View related parts
2010 Chevrolet Express 3500 Rotor, Front
Part Number: 22950036
$143.63 MSRP: $257.65
You Save: $114.02 (45%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Rotor-Front Brake; Disc Brake Hardware Kit; Brake Rotor; Rotor, Front And Rear Wheel Brake
- Position: Front
- Replaces: 88963556, 25819670
- Item Weight: 29.40 Pounds
- Item Dimensions: 13.9 x 14.2 x 3.4 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 22950036
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2010 Chevrolet Express 3500 Submodels:
- Base, LS, LT | 8 Cyl 4.8 L FLEX, 8 Cyl 4.8 L GAS, 8 Cyl 6.0 L CNG, 8 Cyl 6.0 L FLEX, 8 Cyl 6.0 L GAS, 8 Cyl 6.6 L DIESEL
View related parts
2010 Chevrolet Express 3500 Rotor, Front
Part Number: 84587921
$156.52 MSRP: $280.76
You Save: $124.24 (45%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Rotor-Front Brake; Disc Brake Hardware Kit; Brake Rotor; Rotor, Front And Rear Wheel Brake
- Position: Front
- Replaces: 15733625
- Item Weight: 31.60 Pounds
- Item Dimensions: 14.2 x 13.4 x 4.2 inches
- Condition: New
- Fitment Type: Direct Replacement
- Require Quantity: 2
- SKU: 84587921
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2010 Chevrolet Express 3500 Submodels:
- Base, LS, LT | 4 Cyl 2.8 L DIESEL, 6 Cyl 4.3 L FLEX, 6 Cyl 4.3 L GAS, 8 Cyl 4.8 L FLEX, 8 Cyl 4.8 L GAS, 8 Cyl 6.0 L CNG, 8 Cyl 6.0 L FLEX, 8 Cyl 6.0 L GAS, 8 Cyl 6.6 L DIESEL, 8 Cyl 6.6 L GAS

2010 Chevrolet Express 3500 Brake Disc

With a comprehensive array of OEM 2010 Chevrolet Express 3500 Brake Disc, from fuel pumps to door handles, our website is a one-stop-shop for your needs. All our genuine 2010 Chevrolet Express 3500 Brake Disc are backed by the manufacturer's warranty and are offered at competitive prices in the market. Rest assured, you can shop with complete confidence.

2010 Chevrolet Express 3500 Brake Disc Parts Questions & Experts Answers

Q: How to Replace the Front Brake Disc (JH6, JH9) on 2010 Chevrolet Express 3500?
A: Use jack and supports to lift the vehicle and uncover the wheel components first before replacing the front Brake Disc (JH6, JH9). Drive a screwdriver through the Brake Disc vanes to stop the disc spinning before removing the hub extension but retaining its marks to the hub. Install aawl to separate the bolts from the hub extension bolts. You can use a non-metallic mallet in a tapping motion to loosen the hub extension where needed. After marking the hub-disc position attach a c-clamp over the caliper to force pistons in before taking off the clamp. Wedge the brake caliper in place using mechanics wire to prevent brake fluid tube harm from accidental damage. Use mechanics wire to sustain the brake caliper assembly as you disconnect its bolts from the caliper bracket and remove it along with the bracket from the wheel assembly. Before pulling off the disc use an oil penetrant to clean surfaces and apply force through two bolts sized m10 x 1.5 to push the disc away from the hub when the disc retaining washers prove difficult to remove. Clean all rust from the hub flange area using j-42450-a. Also remove debris from both contact surfaces. Place the disc back in its proper position and then add the caliper and its support hardware. Clean the caliper bracket bolts from old adhesive then treat their threads with threadlocker part number gm 12345493 (Canadian 10953488). Apply threadlocker to two-thirds of the bolt and allow it to set for 10 minutes before assembly. Safely add the front wheel hub extension if equipped. Then secure all caliper bracket bolts at 300 nm (221 lb ft) prior to installing the wheel hub extension. Put on the tire and wheel components before you apply the brake pedal at one-third of its range until the pedal pressure achieves solidity in multiple instances. After filling the master cylinder with new brake fluid, you should let the pad and disc pairing form a smooth surface by operating the brakes.