How to replace the steering knuckle on Buick Century?

Initially, lift and adequately support the vehicle. Pull the bearing/hub assembly off, then undo the front lower control arm ball stud and outtie rod end from the Steering Knuckle. Then scribe the strut to the knuckle, alternative it is removed with bolts and nuts which attach the strut to the knuckle and take off the knuckle from the vehicle. On installation, place the knuckle back onto the vehicle while making sure to install the two bolts and nuts that fasten the strut to the knuckle and doing it with a 122 nm(90 ft. Lbs. Of torque). Next, install the outer tie rod to the Steering Knuckle and install the front lower control arm ball stud to the knuckle and also install the front wheel drive shaft bearing. Lastly, lower the vehicle and check the fornt wheel alignment and adjust if necessary.

How to service and repair the steering knuckle on Buick Century?

Service and repair operations for the Steering Knuckle start from elevating the vehicle correctly while providing safe support followed by tire and wheel assembly removal. Start by taking off the front wheel drive shaft bearing. Use the j 41820 ball joint/stud separator (J 41820) on the front lower control arm stud to detach it from the front Steering Knuckle while removing the front lower control arm ball stud-to-knuckle cotter pin and nut. Use the j 24319-b universal steering linkage puller (J 24319-B) to detach the outer Tie Rod End from the Steering Knuckle before scribing the strut to the knuckle and removing connecting bolts so you can remove the knuckle from the vehicle. The installation procedure requires fitting the knuckle onto your vehicle followed by bolting the strut to the knuckle and tightening these bolts to 123 nm (90 ft. Lbs.). Connect the outer tie rod to the Steering Knuckle before adding the front lower control arm ball stud to its attachment point on the knuckle. Finally, install the front lower control arm ball stud nut until it reaches 55 nm (40 ft. Lbs.) torque while shifting the slots to match the cotter pin hole without letting the nut loosen. To finish up install the front lower control arm ball stud cotter pin then reattach the front wheel drive shaft bearing before replacing the tire with the wheel assembly followed by vehicle lowering.

OEM Buick Century Steering Knuckle

Front Steering Knuckle

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

15 Steering Knuckles found

View related parts
Buick Century Knuckle, Driver Side Part Number: 23130696
$388.19 MSRP: $639.48
You Save: $251.29 (40%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Knuckle, Rear Wheel
- Position: Driver Side
- Replaces: 19151396, 18022046, 25816705, 18060616
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1997-2005 Buick Century | Custom, Limited, Special Edition | 6 Cyl 3.1 L GAS
View related parts
Buick Century Knuckle, Driver Side Part Number: 23127629
$268.88 MSRP: $442.93
You Save: $174.05 (40%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Knuckle, Steering (Machining); Knuckle, Steering
- Position: Driver Side
- Replaces: 18060638, 18060652, 88955418, 10434254, 18060680, 20899802, 25816684, 22990752
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1997-2005 Buick Century | Custom, Limited, Special Edition | 6 Cyl 3.1 L GAS
View related parts
Buick Century Knuckle, Passenger Side Part Number: 22990753
$265.66 MSRP: $421.79
You Save: $156.13 (38%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Knuckle, Steering (Machining)
- Position: Passenger Side
- Replaced by: 23127630
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1997-2005 Buick Century | Custom, Limited, Special Edition | 6 Cyl 3.1 L GAS
View related parts
Buick Century Knuckle, Passenger Side Part Number: 23130695
$433.92 MSRP: $623.98
You Save: $190.06 (31%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Knuckle, Rear Wheel
- Position: Passenger Side
- Replaces: 19151397, 18022047, 18060617, 25816704
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1997-2005 Buick Century | Custom, Limited, Special Edition | 6 Cyl 3.1 L GAS
View related parts
Buick Century Knuckle, Driver Side Part Number: 18060577
Product Specifications
- Other Name: Knuckle, Steering
- Position: Driver Side
- Replaces: 18016185
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1994-1996 Buick Century | Custom, Limited, Special | 4 Cyl 2.2 L GAS, 6 Cyl 3.1 L GAS
View related parts
Buick Century Knuckle Part Number: 18018876
Product Specifications
- Other Name: Knuckle, Steering (Machining)
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1993 Buick Century | Custom, Limited, Special | 4 Cyl 2.2 L GAS, 6 Cyl 3.3 L GAS
View related parts
Buick Century Knuckle, Passenger Side Part Number: 18060597
Product Specifications
- Other Name: Knuckle, Steering (Machining); Knuckle, Steering
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1993-1994 Buick Century | Custom, Limited, Special | 4 Cyl 2.2 L GAS, 6 Cyl 3.1 L GAS, 6 Cyl 3.3 L GAS
View related parts
Buick Century Knuckle, Driver Side Part Number: 18060596
Product Specifications
- Other Name: Knuckle, Steering (Machining); Knuckle, Steering
- Position: Driver Side
- Replaces: 18018875
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1993-1994 Buick Century | Custom, Limited, Special | 4 Cyl 2.2 L GAS, 6 Cyl 3.1 L GAS, 6 Cyl 3.3 L GAS
View related parts
Buick Century Knuckle, Passenger Side Part Number: 18060578
Product Specifications
- Other Name: Knuckle, Steering
- Position: Passenger Side
- Replaces: 18016186
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1994-1996 Buick Century | Custom, Limited, Special | 4 Cyl 2.2 L GAS, 6 Cyl 3.1 L GAS
View related parts
Buick Century Knuckle, Rear Passenger Side Part Number: 18023002
Product Specifications
- Other Name: Knuckle, Rear Suspension; Knuckle, Rear Wheel
- Position: Rear Passenger Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1997-2003 Buick Century | Custom, Limited | 6 Cyl 3.1 L GAS
View related parts
Buick Century Knuckle, Rear Driver Side Part Number: 18023001
Product Specifications
- Other Name: Knuckle, Rear Suspension; Knuckle, Rear Wheel
- Position: Rear Driver Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1997-2003 Buick Century | Custom, Limited | 6 Cyl 3.1 L GAS
View related parts
Buick Century Steering Knuckle, Passenger Side Part Number: 18015471
Product Specifications
- Other Name: Knuckle, Steering; Knuckle
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1984-1992 Buick Century | Custom, Estate, Estate Wagon, Limited, Olympia Limited, Special, T-Type | 4 Cyl 2.5 L GAS, 6 Cyl 2.8 L GAS, 6 Cyl 3.0 L GAS, 6 Cyl 3.3 L GAS, 6 Cyl 3.8 L GAS, 6 Cyl 4.3 L DIESEL
View related parts
Buick Century Steering Knuckle, Driver Side Part Number: 18015470
Product Specifications
- Other Name: Knuckle, Steering; Knuckle
- Position: Driver Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1984-1992 Buick Century | Custom, Estate, Estate Wagon, Limited, Olympia Limited, Special, T-Type | 4 Cyl 2.5 L GAS, 6 Cyl 2.8 L GAS, 6 Cyl 3.0 L GAS, 6 Cyl 3.3 L GAS, 6 Cyl 3.8 L GAS, 6 Cyl 4.3 L DIESEL
View related parts
Buick Century Steering Knuckle, Passenger Side Part Number: 14076994
Product Specifications
- Other Name: Knuckle, Steering; Knuckle; Knuckle, Rear Wheel
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1984-1989 Buick Century | Custom, Estate, Estate Wagon, Limited, Olympia Limited, T-Type | 4 Cyl 2.5 L GAS, 6 Cyl 2.8 L GAS, 6 Cyl 3.0 L GAS, 6 Cyl 3.3 L GAS, 6 Cyl 3.8 L GAS, 6 Cyl 4.3 L DIESEL
View related parts
Buick Century Steering Knuckle, Driver Side Part Number: 14076993
Product Specifications
- Other Name: Knuckle; Knuckle, Rear Wheel; Knuckle, Steering
- Position: Driver Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1984-1989 Buick Century | Custom, Estate, Estate Wagon, Limited, Olympia Limited, T-Type | 4 Cyl 2.5 L GAS, 6 Cyl 2.8 L GAS, 6 Cyl 3.0 L GAS, 6 Cyl 3.3 L GAS, 6 Cyl 3.8 L GAS, 6 Cyl 4.3 L DIESEL

Buick Century Steering Knuckle

Want to cut long-term maintenance and repair costs? Choose OEM Steering Knuckle. Those parts deliver top durability you can trust. On our site, you'll find a huge catalog of genuine Buick Century parts. Prices are unbeatable, so you can keep more in your pocket. Every OEM Buick Century Steering Knuckle includes a manufacturer's warranty. You can also get an easy return policy that keeps buying risk free. Fast delivery, get your car on the road quickly. It's simple to search, compare, and order. Stop guessing about quality or fit. Order today and save with parts that last.

The Steering Knuckle of Buick Century vehicles is an important part which plays the role of suspension and steering to link the front wheels and the auto structure. It can retain control arms, tie-rod ends and the wheel hub so that it must undergo vertically movement depending on the surface of the road and, horizontal movements during steering. Different types of Steering Knuckles have been used in Buick Century models based on the drive systems namely rear-wheel drive (RWD) and front or all-wheel or four-wheel drive (FWD/AWD/4WD). RWD vehicle manufacture may have an integral spindle within the Steering Knuckle that is different from the FWD/AWD/4WD which has a drive axle passing through the Steering Knuckle and both of them are connectedbolted or pressed to a hub. The changes in the Steering Knuckle from the most basic kingpin designs to the current ones are as a result of developments in automobile engineering for better and efficient pedals in Buick Century automobiles.

Buick Century Steering Knuckle Parts and Q&A

Knuckle, Driver Side
23127629
Q: How to replace the steering knuckle on Buick Century?
A:
Initially, lift and adequately support the vehicle. Pull the bearing/hub assembly off, then undo the front lower control arm ball stud and outTie Rod End from the Steering Knuckle. Then scribe the strut to the knuckle, alternative it is removed with bolts and nuts which attach the strut to the knuckle and take off the knuckle from the vehicle. On installation, place the knuckle back onto the vehicle while making sure to install the two bolts and nuts that fasten the strut to the knuckle and doing it with a 122 nm(90 ft. Lbs. Of torque). Next, install the outer tie rod to the Steering Knuckle and install the front lower control arm ball stud to the knuckle and also install the front wheel drive shaft bearing. Lastly, lower the vehicle and check the fornt wheel alignment and adjust if necessary.
Knuckle, Driver Side
23130696
Q: How to service and repair the steering knuckle on Buick Century?
A:
Service and repair operations for the Steering Knuckle start from elevating the vehicle correctly while providing safe support followed by tire and wheel assembly removal. Start by taking off the front wheel drive shaft bearing. Use the j 41820 ball joint/stud separator (J 41820) on the front lower control arm stud to detach it from the front Steering Knuckle while removing the front lower control arm ball stud-to-knuckle cotter pin and nut. Use the j 24319-b universal steering linkage puller (J 24319-B) to detach the outer Tie Rod End from the Steering Knuckle before scribing the strut to the knuckle and removing connecting bolts so you can remove the knuckle from the vehicle. The installation procedure requires fitting the knuckle onto your vehicle followed by bolting the strut to the knuckle and tightening these bolts to 123 nm (90 ft. Lbs.). Connect the outer tie rod to the Steering Knuckle before adding the front lower control arm ball stud to its attachment point on the knuckle. Finally, install the front lower control arm ball stud nut until it reaches 55 nm (40 ft. Lbs.) torque while shifting the slots to match the cotter pin hole without letting the nut loosen. To finish up install the front lower control arm ball stud cotter pin then reattach the front wheel drive shaft bearing before replacing the tire with the wheel assembly followed by vehicle lowering.