How to replace the front side door window channel on Buick LeSabre?

The process starts with fully lowering the door window and taking off the trim panel followed by unbowling the half water deflector and extracting the window inner belt seal. Start by tearing the rearward segment of the water deflector and unfastening the window inner belt seal. You can gain access to the lower door frame applique fastener by taking the low section of window Weather Strip out of the door frame gap before you can reach the upper run channel fastener that fulfills this function. Install the window seal into its position on the door frame after attaching the wire harness from the door trim panel. Open the window to expose a 25.4 mm (1 in) opening at the top of the aperture before removing the lower fastener of the run channel. Pull the run channel toward the floor to make space before you remove it. To install this window you need to insert the run channel through the back access hole of the door and move it upward along the window while placing the upper bracket under the door frame applique. Secure the lower fastener by tightening it to 9 n.m (80 lb in). Lower the window completely while taking enough distance from the window seal to mount the upper fastener into both door applique and run channel before making sure the Window Channel bracket rests underneath the door applique. Fasten and tighten the upper fastener to 2 n.m (18 lb in). To prevent the splaying effect when reusing a window Weather Strip pinch the flange mounting area together between your index finger and thumb starting from one end and moving to the other. The window Weather Strip must go into the door frame before adding the window inner belt sealing strip and water deflector and finally the door trim panel.

How to replace the rear side door window channel on Buick LeSabre?

Starting the replacement of the rear side door window front channel requires a fully raised window followed by removal of door trim panel, door module and water deflector. First remove the upper fastener that is both the door applique lower fastener and then loosen the lower fastener. Pull down the window channel assembly until its upper bracket passes by the door applique afterward remove the front window channel from the door. Put the front window channel into the door starting at the top before adding the bottom fastener into its keyhole slot. Use a clockwise rotation on the top part of the front window channel to match it with the bottom edge of the window before installing the upper fastener and tightening it to 2 N.m (18 lb in). Fit the lower fastener to its keyhole slot then secure it at 9 N.m (80 lb in.). The installation process ends with replacement of the water deflector followed by door module and door trim panel.

OEM Buick LeSabre Window Channel

Window Run

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

44 Window Channels found

View related parts
Buick LeSabre Division Bar, Passenger Side Part Number: 20156746
$24.51 MSRP: $46.75
You Save: $22.24 (48%)
ADD TO CART
Product Specifications
- Other Name: Channel; Division Channel; Channel, Rear Door Stationary Vent Division; Channel, Rear Door Stationary Vent
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1984 Buick LeSabre | Custom, Limited | 6 Cyl 4.1 L GAS, 8 Cyl 5.0 L GAS, 8 Cyl 5.7 L DIESEL
View related parts
Buick LeSabre Sash Channel, Front Part Number: 20202349
Product Specifications
- Other Name: Channel, Front Door Window Sash; Window Channel; Lower Sash
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1984-1990 Buick LeSabre | Collector's Edition, Custom, Estate Wagon, Limited | 6 Cyl 3.8 L GAS, 6 Cyl 4.1 L GAS, 8 Cyl 5.0 L GAS, 8 Cyl 5.7 L DIESEL
View related parts
Buick LeSabre Run Channel, Front Passenger Side Part Number: 20666684
Product Specifications
- Other Name: Channel, Front Door Window; Window Channel
- Position: Front Passenger Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1984-1990 Buick LeSabre | Custom, Estate Wagon, Limited | 6 Cyl 3.8 L GAS, 6 Cyl 4.1 L GAS, 8 Cyl 5.0 L GAS, 8 Cyl 5.7 L DIESEL
View related parts
Buick LeSabre Division Bar, Driver Side Part Number: 20133043
Product Specifications
- Other Name: Channel; Window Channel; Division Channel
- Position: Driver Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1984-1985 Buick LeSabre | Custom, Limited | 6 Cyl 3.8 L GAS, 6 Cyl 4.1 L GAS, 8 Cyl 5.0 L GAS, 8 Cyl 5.7 L DIESEL
View related parts
Buick LeSabre Run Channel Lower Retainer Part Number: 20211801
Product Specifications
- Other Name: Ret Assembly Front Door; Run Channel Retainer; Channel, Front Door Window
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1984-1990 Buick LeSabre | Collector's Edition, Custom, Estate Wagon, Limited | 6 Cyl 3.8 L GAS, 6 Cyl 4.1 L GAS, 8 Cyl 5.0 L GAS, 8 Cyl 5.7 L DIESEL
View related parts
Buick LeSabre Sash Channel, Rear Part Number: 20205248
Product Specifications
- Other Name: Channel, Rear Door Window Channel; Window Channel
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1984-1985 Buick LeSabre | Custom, Limited | 6 Cyl 3.8 L GAS, 6 Cyl 4.1 L GAS, 8 Cyl 5.0 L GAS, 8 Cyl 5.7 L DIESEL
View related parts
Buick LeSabre Run Channel, Passenger Side Part Number: 20666688
Product Specifications
- Other Name: Channel Assembly Rear Door; Window Channel; Channel
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1985-1990 Buick LeSabre | Estate Wagon | 8 Cyl 5.0 L GAS, 8 Cyl 5.7 L DIESEL
View related parts
Buick LeSabre Window Channel, Front Driver Side Part Number: 20612775
Product Specifications
- Other Name: Channel, Front Door Window; Run Channel; Upper Channel Retainer; Channel
- Position: Front Driver Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1986-1991 Buick LeSabre | Base, Custom, Limited | 6 Cyl 3.0 L GAS, 6 Cyl 3.8 L GAS
View related parts
Buick LeSabre Run Channel, Passenger Side Part Number: 20666690
Product Specifications
- Other Name: Channel; Window Channel
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1984-1985 Buick LeSabre | Custom, Limited | 6 Cyl 3.8 L GAS, 6 Cyl 4.1 L GAS, 8 Cyl 5.0 L GAS, 8 Cyl 5.7 L DIESEL
View related parts
Buick LeSabre Run Channel Part Number: 20666691
Product Specifications
- Other Name: Channel; Window Channel
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1984-1985 Buick LeSabre | Custom, Limited | 6 Cyl 3.8 L GAS, 6 Cyl 4.1 L GAS, 8 Cyl 5.0 L GAS, 8 Cyl 5.7 L DIESEL
View related parts
Buick LeSabre Window Channel, Passenger Side Part Number: 25557107
Product Specifications
- Other Name: Channel Assembly-Front Side Door Window Rear; Run Channel; Glass Run; Channel, Front Door Window
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1992-1999 Buick LeSabre | Custom, Limited | 6 Cyl 3.8 L GAS
View related parts
Buick LeSabre Window Channel, Driver Side Part Number: 25557108
Product Specifications
- Other Name: Channel Assembly-Front Side Door Window Rear; Run Channel; Glass Run; Channel, Front Door Window
- Position: Driver Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1992-1999 Buick LeSabre | Custom, Limited | 6 Cyl 3.8 L GAS
View related parts
Buick LeSabre Window Channel, Front Passenger Side Part Number: 25557109
Product Specifications
- Other Name: Channel, Front Door Window; Run Channel; Glass Run; Division Channel
- Position: Front Passenger Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1992-1999 Buick LeSabre | Custom, Limited | 6 Cyl 3.8 L GAS
View related parts
Buick LeSabre Window Channel, Front Driver Side Part Number: 25557110
Product Specifications
- Other Name: Channel, Front Door Window; Run Channel; Glass Run; Division Channel
- Position: Front Driver Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1992-1999 Buick LeSabre | Custom, Limited | 6 Cyl 3.8 L GAS
View related parts
Buick LeSabre Division Channel, Rear Driver Side Part Number: 20737343
Product Specifications
- Other Name: Channel, Rear Door Stationary Vent; Window Channel
- Position: Rear Driver Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1988-1991 Buick LeSabre | Custom, Limited | 6 Cyl 3.8 L GAS
View related parts
Buick LeSabre Division Channel, Rear Passenger Side Part Number: 20737342
Product Specifications
- Other Name: Channel, Rear Door Stationary Vent; Window Channel
- Position: Rear Passenger Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1988-1991 Buick LeSabre | Custom, Limited | 6 Cyl 3.8 L GAS
View related parts
Buick LeSabre Run Channel Lower Retainer, Front Part Number: 20211802
Product Specifications
- Other Name: Channel, Front Door Window; Run Channel Retainer
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1984-1990 Buick LeSabre | Collector's Edition, Custom, Estate Wagon, Limited | 6 Cyl 3.8 L GAS, 6 Cyl 4.1 L GAS, 8 Cyl 5.0 L GAS, 8 Cyl 5.7 L DIESEL
View related parts
Buick LeSabre Run Channel, Driver Side Part Number: 25745482
Product Specifications
- Other Name: Channel Assembly-Front Side Door Window Rear; Window Channel; Channel, Front Door Window
- Position: Driver Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2005 Buick LeSabre | Custom, Limited | 6 Cyl 3.8 L GAS
View related parts
Buick LeSabre Run Channel, Rear Passenger Side Part Number: 20623620
Product Specifications
- Other Name: Weatherstrip, Rear Side Door Window Glass Running (Outer & Inner); Window Channel; Channel, Rear Door Window Glass Running
- Position: Rear Passenger Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1986-1991 Buick LeSabre | Base, Custom, Limited | 6 Cyl 3.0 L GAS, 6 Cyl 3.8 L GAS
View related parts
Buick LeSabre Run Channel, Rear Driver Side Part Number: 20623621
Product Specifications
- Other Name: Weatherstrip, Rear Side Door Window Glass Running (Outer & Inner); Window Channel; Channel, Rear Door Window Glass Running
- Position: Rear Driver Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1986-1991 Buick LeSabre | Base, Custom, Limited | 6 Cyl 3.0 L GAS, 6 Cyl 3.8 L GAS

| Page 1 of 3 |Next >

1-20 of 44 Results

Buick LeSabre Window Channel

Want to cut long-term maintenance and repair costs? Choose OEM Window Channel. Those parts deliver top durability you can trust. On our site, you'll find a huge catalog of genuine Buick LeSabre parts. Prices are unbeatable, so you can keep more in your pocket. Every OEM Buick LeSabre Window Channel includes a manufacturer's warranty. You can also get an easy return policy that keeps buying risk free. Fast delivery, get your car on the road quickly. It's simple to search, compare, and order. Stop guessing about quality or fit. Order today and save with parts that last.

Buick LeSabre Window Channel is a part of Buick LeSabre vehicles which plays a very important role in boosting the efficiency of vehicles. This Window Channel proves particularly significant in making sure that the window glass stays properly seated to discourage the intrusion of dirt together with water in the cabin. The Window Channel therefore has a functional role in enhancing the ease of movement of the sash of a particular window mainly in enhancing the operability of windows which is important in making human habitat more comfortable as well as safe. This window channel suits and fits the Buick LeSabre models manufactured between 1959 and 2005, when it comes to functionality, the Window Channel helps to seal the automotive structure in a way which leads to improved energy conditions in the interior. It is advisable that Window Channel be maintained often so that it does not acquire any dirt that would interfere with the use of windows. That is why such models as Buick LeSabre, characterized by longevity and increased performance, can successfully use the reliability of Window Channel to maintain smooth operation of windows over the entire period of operation. Additional components of the Window Channel are weath sealing to expand the special bonus of the car in the AE3F automotive market. In sum, it is impossible to overestimate the significance of the Buick LeSabre Window Channel as the car part not only contributes to the operational performance of the car but also actively provides for the safety and comfort of the passengers in great measure, and in so doing, solidifies this automobile brand's rep as a reliable one among Buick fans.

Buick LeSabre Window Channel Parts and Q&A

Run Channel, Driver Side
25745482
Q: How to replace the front side door window channel on Buick LeSabre?
A:
The process starts with fully lowering the door window and taking off the trim panel followed by unbowling the half water deflector and extracting the window inner belt seal. Start by tearing the rearward segment of the water deflector and unfastening the window inner belt seal. You can gain access to the lower door frame applique fastener by taking the low section of window Weather Strip out of the door frame gap before you can reach the upper run channel fastener that fulfills this function. Install the window seal into its position on the door frame after attaching the wire harness from the door trim panel. Open the window to expose a 25.4 mm (1 in) opening at the top of the aperture before removing the lower fastener of the run channel. Pull the run channel toward the floor to make space before you remove it. To install this window you need to insert the run channel through the back access hole of the door and move it upward along the window while placing the upper bracket under the door frame applique. Secure the lower fastener by tightening it to 9 n.m (80 lb in). Lower the window completely while taking enough distance from the window seal to mount the upper fastener into both door applique and run channel before making sure the Window Channel bracket rests underneath the door applique. Fasten and tighten the upper fastener to 2 n.m (18 lb in). To prevent the splaying effect when reusing a window Weather Strip pinch the flange mounting area together between your index finger and thumb starting from one end and moving to the other. The window Weather Strip must go into the door frame before adding the window inner belt sealing strip and water deflector and finally the door trim panel.
Sash Channel, Driver Side
25745478
Q: How to replace the rear side door window channel on Buick LeSabre?
A:
Starting the replacement of the rear side door window front channel requires a fully raised window followed by removal of door trim panel, door module and water deflector. First remove the upper fastener that is both the door applique lower fastener and then loosen the lower fastener. Pull down the window channel assembly until its upper bracket passes by the door applique afterward remove the front window channel from the door. Put the front window channel into the door starting at the top before adding the bottom fastener into its keyhole slot. Use a clockwise rotation on the top part of the front window channel to match it with the bottom edge of the window before installing the upper fastener and tightening it to 2 N.m (18 lb in). Fit the lower fastener to its keyhole slot then secure it at 9 N.m (80 lb in.). The installation process ends with replacement of the water deflector followed by door module and door trim panel.