How to service and repair the front brake calipers on Buick Park Avenue?

Service and repair work on the front brake caliper starts with taking it out of the vehicle. Putting your fingers close to the Piston under compressed air pressure puts you at significant risk of injuring yourself. Clean cloths inside caliper housing protect pins from harm during removal when you supply enough compressor air to move them smoothly out of their bores. Pump low-pressure compressed air into the caliper bore until the Brake Caliper Piston moves out through the fluid inlet hole. A short wooden or plastic tool helps you take out and dispose of both the Piston dust boot seal and Piston seal from the caliper unit. First disconnect the caliper bleeder components for further work. Avoid brushing off your Brake Caliper Piston during cleaning. Use denatured alcohol or suitable cleaning solution to purge all dirt from both the caliper Piston bore and seal area plus the Piston itself. Filter clean non-lubricated air to dry the components while looking for cracks, scoring, pitting, excessive rust, and heavy corrosion inside the caliper bore. Plan to replace the caliper assembly when fine emery paper fails to remove light rust or corrosion from the components. Replace the whole caliper unit whenever you find cracks, scratches, or major corrosion in it. If you find damage on the chrome-plated caliper Piston examine or damage to the caliper Piston please replace it. Apply delco supreme 11(R) brake fluid equivalent to gm p/n 12377967 (Canadian P/N 992667) or dot-3 fluid from a clean container to the new Piston seal and install it into the caliper bore. First place the caliper Piston inside the bore space before adding the new Piston dust boot seal over the Piston. Seat the Piston seal completely by using the j 35777 caliper Piston seal installer (J 35777). Affix and tighten the bleeder valve and cap securely to finish the installation process. After installation place the caliper back into position.

How to replace the front brake calipers on Buick Park Avenue?

Before working on the front brake caliper check the fluid level in the brake master cylinder reservoir. When the fluid is higher than halfway between its marks drain it until it reaches the same level. Lift the car for access and take off the tire and wheel part. Our first step is installing two wheel lug nuts by hand while keeping the rotor in place on the hub. Place a large c-clamp on top of the brake caliper and gradually tighten to push the caliper piston into the brake rotor until it can pass through, then remove the c-clamp. Disconnect the brake caliper bolt's brake hose while discarding the two copper brake hose gaskets but sealing off the ends with pliers. Take off the caliper bolts at their pins and lift the caliper away from the bracket. Inspect the pin bolt boots for spots where leather has damaged or torn through. Before placing the brake caliper pin bolts back use a shop towel to clean them and put on a thin coat of niglube(R) grease without adding lubricant to brake pad parts. Press the brake caliper above brake pads into the Brake Caliper Bracket and fasten it using caliper pin bolts until they reach a torque of 85 nm (63 ft. Lbs.). Attach the brake hose bolt to the brake caliper by assembling it with new copper brake hose gaskets then tighten it to 45 nm (33 ft. Lbs.). Depress the brake pedal to a middle position during 2/3rd travel then let it go slowly and repeat until pedal pressure becomes steady. You should put the tire and wheel set onto the vehicle then lower it to the ground when you have removed both wheel lug nuts.

OEM Buick Park Avenue Brake Calipers

Caliper

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

17 Brake Calipers found

View related parts
Buick Park Avenue Caliper Assembly, Front Part Number: 19141284
$33.79 MSRP: $60.04
You Save: $26.25 (44%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper Assembly, Front Brake (W/O Brake Pads) (Remanufacture); Brake Caliper; Caliper
- Position: Front
- Replaces: 18037091, 18018731, 18060166
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1991-1993 Buick Park Avenue | Base, Ultra | 6 Cyl 3.8 L GAS
View related parts
Buick Park Avenue Caliper Assembly, Front Part Number: 19141283
$48.90 MSRP: $89.20
You Save: $40.30 (46%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper Assembly, Front Brake (W/O Brake Pads) (Remanufacture); Brake Caliper; Caliper
- Position: Front
- Replaces: 18060165, 18037092, 18018730
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1991-1993 Buick Park Avenue | Base, Ultra | 6 Cyl 3.8 L GAS
View related parts
Buick Park Avenue Caliper, Front Driver Side Part Number: 18046196
$145.18 MSRP: $284.26
You Save: $139.08 (49%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper Assembly, Front Brake (Service); Brake Caliper; Caliper, Wheel Brake Cylinder/Caliper
- Position: Front Driver Side
- Replaces: 18029818
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1997-2005 Buick Park Avenue | Base, Ultra | 6 Cyl 3.8 L GAS
View related parts
Buick Park Avenue Caliper, Front Passenger Side Part Number: 18046197
Product Specifications
- Other Name: Caliper Assembly, Front Brake (Service); Brake Caliper; Caliper, Wheel Brake Cylinder/Caliper
- Position: Front Passenger Side
- Replaces: 18029819
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1997-2005 Buick Park Avenue | Base, Ultra | 6 Cyl 3.8 L GAS
View related parts
Buick Park Avenue Caliper, Driver Side Part Number: 18040794
Product Specifications
- Other Name: Brake Caliper
- Position: Driver Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1999 Buick Park Avenue | Base, Ultra | 6 Cyl 3.8 L GAS
View related parts
Buick Park Avenue Caliper, Front Part Number: 18014745
Product Specifications
- Other Name: Caliper, Front Brake; Brake Caliper; Caliper, Wheel Brake Cylinder/Caliper
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1991 Buick Park Avenue | Base, Ultra | 6 Cyl 3.8 L GAS
View related parts
Buick Park Avenue Caliper, Front Part Number: 18014744
Product Specifications
- Other Name: Caliper, Front Brake; Brake Caliper; Caliper, Wheel Brake Cylinder/Caliper
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1991 Buick Park Avenue | Base, Ultra | 6 Cyl 3.8 L GAS
View related parts
Buick Park Avenue Caliper Part Number: 89047652
Product Specifications
- Other Name: Caliper Assembly, Rear Brake; Brake Caliper; Caliper, Wheel Brake Cylinder/Caliper
- Position: Rear
- Replaces: 18042414
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2005 Buick Park Avenue | Base, Ultra | 6 Cyl 3.8 L GAS
View related parts
Buick Park Avenue Caliper Part Number: 89047651
Product Specifications
- Other Name: Caliper Assembly, Rear Brake; Brake Caliper; Caliper, Wheel Brake Cylinder/Caliper
- Position: Rear
- Replaces: 18042413
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2005 Buick Park Avenue | Base, Ultra | 6 Cyl 3.8 L GAS
View related parts
Buick Park Avenue Caliper Part Number: 88962838
Product Specifications
- Other Name: Caliper Assembly, Rear Brake; Brake Caliper; Caliper, Wheel Brake Cylinder/Caliper
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1999 Buick Park Avenue | Base, Ultra | 6 Cyl 3.8 L GAS
View related parts
Buick Park Avenue Caliper Part Number: 88962830
Product Specifications
- Other Name: Caliper Assembly, Rear Brake; Brake Caliper; Caliper, Wheel Brake Cylinder/Caliper
- Position: Rear
- Replaces: 18029821
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1997-1998 Buick Park Avenue | Base, Ultra | 6 Cyl 3.8 L GAS
View related parts
Buick Park Avenue Caliper Part Number: 88962829
Product Specifications
- Other Name: Caliper Assembly, Rear Brake; Brake Caliper; Caliper, Wheel Brake Cylinder/Caliper
- Position: Rear
- Replaces: 18019526, 18029820
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1997-1998 Buick Park Avenue | Base, Ultra | 6 Cyl 3.8 L GAS
View related parts
Buick Park Avenue Overhaul Kit, Rear Part Number: 18042415
Product Specifications
- Other Name: Caliper Kit, Rear Brake; Brake Caliper Repair Kit; Disc Brake Hardware Kit; Caliper Overhaul Kit; Caliper Kit, Wheel Brake Cylinder/Caliper
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2005 Buick Park Avenue | Base, Ultra | 6 Cyl 3.8 L GAS
View related parts
Buick Park Avenue Caliper Assembly, Front Part Number: 18029938
Product Specifications
- Other Name: Caliper Assembly, Front Brake (Service); Brake Caliper; Caliper; Caliper, Wheel Brake Cylinder/Caliper
- Position: Front
- Replaces: 18029929, 18021252
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1994-1996 Buick Park Avenue | Base, Ultra | 6 Cyl 3.8 L GAS
View related parts
Buick Park Avenue Caliper Assembly, Front Part Number: 18029937
Product Specifications
- Other Name: Caliper Assembly, Front Brake (Service); Brake Caliper; Caliper; Caliper, Wheel Brake Cylinder/Caliper
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1994-1996 Buick Park Avenue | Base, Ultra | 6 Cyl 3.8 L GAS
View related parts
Buick Park Avenue Overhaul Kit Part Number: 18029823
Product Specifications
- Other Name: Caliper Kit, Wheel Brake Cylinder/Caliper; Brake Caliper Repair Kit; Disc Brake Hardware Kit; Caliper Overhaul Kit
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1997-1999 Buick Park Avenue | Base, Ultra | 6 Cyl 3.8 L GAS
View related parts
Buick Park Avenue Overhaul Kit, Front Part Number: 18017156
Product Specifications
- Other Name: Caliper Kit, Front Brake; Brake Caliper Repair Kit; Disc Brake Hardware Kit; Caliper Overhaul Kit; Wheel Brake Cylinder/Caliper Piston Kit.
- Position: Front
- Replaces: 18024958
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1991-2005 Buick Park Avenue | Base, Ultra | 6 Cyl 3.8 L GAS

Buick Park Avenue Brake Calipers

Want to cut long-term maintenance and repair costs? Choose OEM Brake Calipers. Those parts deliver top durability you can trust. On our site, you'll find a huge catalog of genuine Buick Park Avenue parts. Prices are unbeatable, so you can keep more in your pocket. Every OEM Buick Park Avenue Brake Calipers includes a manufacturer's warranty. You can also get an easy return policy that keeps buying risk free. Fast delivery, get your car on the road quickly. It's simple to search, compare, and order. Stop guessing about quality or fit. Order today and save with parts that last.

Specifically, the Buick Park Avenue Brake Calipers refer to its related braking systems that are recognized to be one of the best on the market for various models of the Park Avenue. These Brake Calipers are very crucial in increasing both efficiency and safety by exerting force on the brake pads to make contact with the rotors in order to create friction needed for a vehicle to be brought to a standstill. Comes both fixed and floating that meet distinct driving requirements; fixed that assist through the use of opposing pistons and floating to enable more flexibility. In this respect, these Brake Calipers transcend their work potentiality and are key to other areas that define the Buick Park Avenue. Adaptability to specific versions of Park Avenue underlines the fact that fuel consumers will pull off smooth, regular and strong brakes. Other features remain fine tuning of the car such as the new Dynaride system that was in previous model to control the height and stability of the vehicle. The Buick Park Avenue Brake Calipers also have the function of supporting the braking system and being safe for the operation on the roads, thus making an addition to the unique features of the company's models. Being one of the oldest Buick models, the Buick Park Avenue and its Brake Calipers are synonyms to luxury and reliability thus supporting the brand's policy of providing only the best to its consumers.

Buick Park Avenue Brake Calipers Parts and Q&A

Caliper, Front Driver Side
18046196
Q: How to service and repair the front brake calipers on Buick Park Avenue?
A:
Service and repair work on the front brake caliper starts with taking it out of the vehicle. Putting your fingers close to the Piston under compressed air pressure puts you at significant risk of injuring yourself. Clean cloths inside caliper housing protect pins from harm during removal when you supply enough compressor air to move them smoothly out of their bores. Pump low-pressure compressed air into the caliper bore until the Brake Caliper Piston moves out through the fluid inlet hole. A short wooden or plastic tool helps you take out and dispose of both the Piston dust boot seal and Piston seal from the caliper unit. First disconnect the caliper bleeder components for further work. Avoid brushing off your Brake Caliper Piston during cleaning. Use denatured alcohol or suitable cleaning solution to purge all dirt from both the caliper Piston bore and seal area plus the Piston itself. Filter clean non-lubricated air to dry the components while looking for cracks, scoring, pitting, excessive rust, and heavy corrosion inside the caliper bore. Plan to replace the caliper assembly when fine emery paper fails to remove light rust or corrosion from the components. Replace the whole caliper unit whenever you find cracks, scratches, or major corrosion in it. If you find damage on the chrome-plated caliper Piston examine or damage to the caliper Piston please replace it. Apply delco supreme 11(R) brake fluid equivalent to gm p/n 12377967 (Canadian P/N 992667) or dot-3 fluid from a clean container to the new Piston seal and install it into the caliper bore. First place the caliper Piston inside the bore space before adding the new Piston dust boot seal over the Piston. Seat the Piston seal completely by using the j 35777 caliper Piston seal installer (J 35777). Affix and tighten the bleeder valve and cap securely to finish the installation process. After installation place the caliper back into position.
Caliper, Front Passenger Side
18046197
Q: How to replace the front brake calipers on Buick Park Avenue?
A:
Before working on the front brake caliper check the fluid level in the brake master cylinder reservoir. When the fluid is higher than halfway between its marks drain it until it reaches the same level. Lift the car for access and take off the tire and wheel part. Our first step is installing two wheel lug nuts by hand while keeping the rotor in place on the hub. Place a large c-clamp on top of the brake caliper and gradually tighten to push the caliper piston into the brake rotor until it can pass through, then remove the c-clamp. Disconnect the brake caliper bolt's brake hose while discarding the two copper brake hose gaskets but sealing off the ends with pliers. Take off the caliper bolts at their pins and lift the caliper away from the bracket. Inspect the pin bolt boots for spots where leather has damaged or torn through. Before placing the brake caliper pin bolts back use a shop towel to clean them and put on a thin coat of niglube(R) grease without adding lubricant to brake pad parts. Press the brake caliper above brake pads into the Brake Caliper Bracket and fasten it using caliper pin bolts until they reach a torque of 85 nm (63 ft. Lbs.). Attach the brake hose bolt to the brake caliper by assembling it with new copper brake hose gaskets then tighten it to 45 nm (33 ft. Lbs.). Depress the brake pedal to a middle position during 2/3rd travel then let it go slowly and repeat until pedal pressure becomes steady. You should put the tire and wheel set onto the vehicle then lower it to the ground when you have removed both wheel lug nuts.