How to replace the front wheel bearing and wheel hub on Chevrolet Corvette?

Start by raising the vehicle and placing supports underneath. Then take off the tire and wheel unit. Take off the Wheel Speed Sensor electrical plug before removing both brake caliper and rotor. Place the jackstand under the lower Control Arm after unlocking its connection to the stabilizer shaft. The j 42188 tool helps you disconnect both the lower ball joint stud and outer tie rod ball stud from the Steering Knuckle. When you extract all the wheel hub bolts you can pull out the hub and bearing assembly from the Steering Knuckle. Insert the hub and bearing assembly into the Steering Knuckle by fitting the wheel hub mounting bolts before securing them to 130 nm (96 ft. Lbs.). Position the lower Control Arm ball stud onto the Steering Knuckle and remove the jackstand before putting the steering linkage outer tie rod ball stud into place. Connect the Wheel Speed Sensor power wires and join the stabilizer shaft to the lower Control Arm before putting back the brake rotor and caliper. Install tire and wheel assembly back on the vehicle then lower it to ground level while ensuring proper wheel toe adjustment according to specifications.

How to replace the rear wheel bearing and wheel hub on Chevrolet Corvette?

You should start by lifting the vehicle and supporting it before you take off the tire and wheel unit. When working disconnect the wheel speed electrical wire and the rtd position sensor link as necessary. First disconnect the brake caliper and rotor before filtering out the shock absorber solenoid electrical connector on equipped models. Sever the Tie Rod End from the suspension knuckle and take off its holding parts including the nut retainer, nut, and washer. Take the suspension knuckle apart by freeing the upper Control Arm out of it and disconnecting the lower Control Arm ball joint stud. Pull out the suspension knuckle from the vehicle before removing wheel hub mounting bolts so you can take out the hub and bearing assembly. Modeled installation demands the use of appropriate wheel hub/wheel speed sensor parts since the front and back sensors are distinct. Place the wheel hub and bearing assembly onto the suspension knuckle before tightening its wheel hub mounting bolts to 130 nm (96 ft. Lbs.). Place the lower Control Arm ball stud back into the suspension knuckle before joining it to the upper Control Arm. Put the Spindle Nut and washer onto the suspension assembly then add the retainer. Thread the outer Tie Rod End onto the suspension knuckle. Reposition the brake rotor and its caliper before docking the speed sensor and shock absorber electrical connections. Add the real-time damping position sensor link if installed before putting on the wheel and tire assembly then lowering the vehicle into place.

OEM Chevrolet Corvette Wheel Hub

Wheel Axle Hub

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

17 Wheel Hubs found

View related parts
Chevrolet Corvette Hub & Bearing, Rear Part Number: 23193306
$144.74 MSRP: $259.62
You Save: $114.88 (45%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Hub Assembly-Rear Wheel (W/Bearing); Wheel Bearing and Hub Assembly; Wheel Bearing; Axle Bearing; Wheel Hub; Hub & Bearing Assembly; Hub, Rear Wheel
- Position: Rear
- Replaced by: 85144277
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2014-2019 Chevrolet Corvette | Grand Sport, Stingray, Z06, ZR1 | 8 Cyl 6.2 L GAS
View related parts
Chevrolet Corvette Front Hub & Bearing Part Number: 22804376
$294.79 MSRP: $528.78
You Save: $233.99 (45%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Hub Assembly-Front Wheel (W/ Bearing & Sensor); Repair Kit; Wheel Bearing; Axle Bearing; ABS Sensor; Rear Speed Sensor; Front Speed Sensor; Hub & Bearing Assembly; Front & Rear Wheel Hubs.
- Position: Front
- Replaced by: 19421347
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2009-2013 Chevrolet Corvette | 427, Base, Grand Sport, Z06, Z06 Carbon, ZR1 | 8 Cyl 6.2 L GAS, 8 Cyl 7.0 L GAS
View related parts
Chevrolet Corvette Front Hub & Bearing Part Number: 20981829
$116.39 MSRP: $227.88
You Save: $111.49 (49%)
ADD TO CART
Product Specifications
- Other Name: Hub, Front Wheel; Wheel Hub Repair Kit; Wheel Bearing; Axle Bearing; Wheel Hub; Hub & Bearing
- Position: Front
- Replaced by: 85144278
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2014-2019 Chevrolet Corvette | Grand Sport, Stingray, Z06, ZR1 | 8 Cyl 6.2 L GAS
View related parts
Chevrolet Corvette Front Hub & Bearing Part Number: 85150737
$118.23 MSRP: $212.08
You Save: $93.85 (45%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Hub, Front Wheel
- Position: Front
- Replaced by: 87833625
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2023 Chevrolet Corvette | Stingray, Z06 | 8 Cyl 5.5 L GAS, 8 Cyl 6.2 L GAS
View related parts
Chevrolet Corvette Hub Assembly, Front Part Number: 23291487
$90.87 MSRP: $162.26
You Save: $71.39 (44%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Hub, Front Wheel; Wheel Bearing; Axle Bearing; Front Hub & Bearing
- Position: Front
- Replaced by: 85120533
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2020-2023 Chevrolet Corvette | Stingray, Z06 | 8 Cyl 5.5 L GAS, 8 Cyl 6.2 L GAS
View related parts
Chevrolet Corvette Hub Assembly, Front Part Number: 87833625
$118.23 MSRP: $212.08
You Save: $93.85 (45%)
ADD TO CART
Product Specifications
- Other Name: Hub, Front Wheel
- Position: Front
- Replaces: 85150737
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2023-2024 Chevrolet Corvette | Stingray, Z06 | 8 Cyl 5.5 L GAS, 8 Cyl 6.2 L GAS
View related parts
Chevrolet Corvette Hub Assembly, Front Part Number: 87833622
$109.01 MSRP: $194.66
You Save: $85.65 (44%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Hub, Front Wheel; Hub, Rear Wheel
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2024 Chevrolet Corvette | E-Ray, Stingray | 8 Cyl 6.2 L FULL HYBRID EV-GAS (FHEV), 8 Cyl 6.2 L GAS
View related parts
Chevrolet Corvette Hub Assembly, Rear Part Number: 86812989
$119.37 MSRP: $214.12
You Save: $94.75 (45%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Hub Assembly-Rear Wheel (W/Bearing); Rear Hub & Bearing; Hub, Rear Wheel
- Position: Rear
- Replaced by: 87833624
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2023-2024 Chevrolet Corvette | Stingray, Z06 | 8 Cyl 5.5 L GAS, 8 Cyl 6.2 L GAS
View related parts
Chevrolet Corvette Front Hub & Bearing Part Number: 19421349
$235.86 MSRP: $457.77
You Save: $221.91 (49%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Bearing Assembly, Front Wheel; Rear Speed Sensor; Front Speed Sensor; Hub & Bearing Assembly; Front & Rear Wheel Hubs.
- Position: Front
- Replaces: 19208046, 19208047, 13588035
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2009-2013 Chevrolet Corvette | 427, Base, Grand Sport, Z06, Z06 Carbon, ZR1 | 8 Cyl 6.2 L GAS, 8 Cyl 7.0 L GAS
View related parts
Chevrolet Corvette Rear Speed Sensor Part Number: 88967288
Product Specifications
- Other Name: Hub, Rear Wheel; Wheel Bearing and Hub Assembly; ABS Sensor.; Hub & Bearing; Hub & Bearing Assembly
- Position: Rear
- Replaces: 07470571, 7470571
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1997-2008 Chevrolet Corvette | 427 Limited Edition Z06, 50th Anniversary Edition, 50th Anniversary Edition Pace Car, Base, Indianapolis 500 Pace Car, Z06 | 8 Cyl 5.7 L GAS, 8 Cyl 6.0 L GAS, 8 Cyl 6.2 L GAS, 8 Cyl 7.0 L GAS
View related parts
Chevrolet Corvette Front Hub & Bearing Part Number: 88967287
Product Specifications
- Other Name: Hub Assembly, Front Wheel (W/Bearing & Speed Sensor); Wheel Hub Repair Kit; ABS Sensor.; Hub & Bearing; Front Speed Sensor; Hub, Front Wheel
- Position: Front
- Replaces: 07470569, 7470569
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1997-2008 Chevrolet Corvette | 427 Limited Edition Z06, 50th Anniversary Edition, 50th Anniversary Edition Pace Car, Base, Indianapolis 500 Pace Car, Z06 | 8 Cyl 5.7 L GAS, 8 Cyl 6.0 L GAS, 8 Cyl 6.2 L GAS, 8 Cyl 7.0 L GAS
View related parts
Chevrolet Corvette Hub, Front Part Number: 12413041
Product Specifications
- Other Name: Hub Assembly, Front Wheel; Wheel Bearing and Hub Assembly; Wheel Hub Repair Kit; Hub, Front Wheel
- Position: Front
- Replaces: 7470551, 07470551
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1984-1990 Chevrolet Corvette | 35th Anniversary Edition, Base, Indianapolis 500 Pace Car, ZR-1 | 8 Cyl 5.7 L GAS
View related parts
Chevrolet Corvette Hub Part Number: 7466965
Product Specifications
- Other Name: Hub Assembly
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1991 Chevrolet Corvette | Base, ZR-1 | 8 Cyl 5.7 L GAS
View related parts
Chevrolet Corvette Hub Part Number: 7466945
Product Specifications
- Other Name: Hub Assembly-R; Wheel Hub
- Replaced by: 7470501
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1984-1991 Chevrolet Corvette | 35th Anniversary Edition, Base, Indianapolis 500 Pace Car, ZR-1 | 8 Cyl 5.7 L GAS
View related parts
Chevrolet Corvette Hub & Bearing, Rear Part Number: 7470501
Product Specifications
- Other Name: Hub Assembly, Rear Wheel; Wheel Bearing & Hub; Axle Bearing; Wheel Hub; Hub; Hub, Rear Wheel
- Position: Rear
- Replaces: 7466945
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1984-1996 Chevrolet Corvette | 35th Anniversary Edition, 40th Anniversary Edition, Base, Collector's Edition, Grand Sport, Indianapolis 500 Pace Car, ZR-1 | 8 Cyl 5.7 L GAS
View related parts
Chevrolet Corvette Hub & Bearing, Front Part Number: 12413001
Product Specifications
- Other Name: Hub Assembly, Front Wheel; Wheel Bearing and Hub Assembly; Wheel Hub Repair Kit; Wheel Bearing; Axle Bearing; Wheel Hub; Hub; Hub, Front Wheel
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1991-1996 Chevrolet Corvette | 40th Anniversary Edition, Base, Collector's Edition, Grand Sport, Indianapolis 500 Pace Car, ZR-1 | 8 Cyl 5.7 L GAS
View related parts
Chevrolet Corvette Hub Assembly, Rear Part Number: 23291488
$93.79 MSRP: $167.48
You Save: $73.69 (44%)
Product Specifications
- Other Name: Hub Assembly-Rear Wheel (W/Bearing); Wheel Bearing; Wheel Hub; Rear Hub & Bearing; Hub, Rear Wheel
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2020-2024 Chevrolet Corvette | Stingray, Z06 | 8 Cyl 5.5 L GAS, 8 Cyl 6.2 L GAS

Chevrolet Corvette Wheel Hub

Want to cut long-term maintenance and repair costs? Choose OEM Wheel Hub. Those parts deliver top durability you can trust. On our site, you'll find a huge catalog of genuine Chevrolet Corvette parts. Prices are unbeatable, so you can keep more in your pocket. Every OEM Chevrolet Corvette Wheel Hub includes a manufacturer's warranty. You can also get an easy return policy that keeps buying risk free. Fast delivery, get your car on the road quickly. It's simple to search, compare, and order. Stop guessing about quality or fit. Order today and save with parts that last.

Chevrolet Corvette cars' Wheel Hub works as a link between the wheels and the car that provides safer controlling of steering as well as stability. It contains hubs, bearings, sensors, brake system and other parts which help in smooth rotation of wheel and firm fixing of the same. The Chevrolet Corvette has gone through the use of different Wheel Hub designs up to date, with each design have its unique characteristic such as bolt patterns and axle extension width among others. Some basic choices are produced but specially designed replacements that are direct-fit to the Corvette are preferred. Its installation process is very crucial because torque is applied properly during its fixations so that mechanical problems do not happen, thus proving the relevance of the Wheel Hub which enhances the Corvette's operational capability on the road.

Chevrolet Corvette Wheel Hub Parts and Q&A

Front Hub & Bearing
88967287
Q: How to replace the front wheel bearing and wheel hub on Chevrolet Corvette?
A:
Start by raising the vehicle and placing supports underneath. Then take off the tire and wheel unit. Take off the Wheel Speed Sensor electrical plug before removing both brake caliper and rotor. Place the jackstand under the lower Control Arm after unlocking its connection to the stabilizer shaft. The j 42188 tool helps you disconnect both the lower ball joint stud and outer tie rod ball stud from the Steering Knuckle. When you extract all the wheel hub bolts you can pull out the hub and bearing assembly from the Steering Knuckle. Insert the hub and bearing assembly into the Steering Knuckle by fitting the wheel hub mounting bolts before securing them to 130 nm (96 ft. Lbs.). Position the lower Control Arm ball stud onto the Steering Knuckle and remove the jackstand before putting the steering linkage outer tie rod ball stud into place. Connect the Wheel Speed Sensor power wires and join the stabilizer shaft to the lower Control Arm before putting back the brake rotor and caliper. Install tire and wheel assembly back on the vehicle then lower it to ground level while ensuring proper wheel toe adjustment according to specifications.
Rear Speed Sensor
88967288
Q: How to replace the rear wheel bearing and wheel hub on Chevrolet Corvette?
A:
You should start by lifting the vehicle and supporting it before you take off the tire and wheel unit. When working disconnect the wheel speed electrical wire and the rtd position sensor link as necessary. First disconnect the brake caliper and rotor before filtering out the shock absorber solenoid electrical connector on equipped models. Sever the Tie Rod End from the suspension knuckle and take off its holding parts including the nut retainer, nut, and washer. Take the suspension knuckle apart by freeing the upper Control Arm out of it and disconnecting the lower Control Arm ball joint stud. Pull out the suspension knuckle from the vehicle before removing wheel hub mounting bolts so you can take out the hub and bearing assembly. Modeled installation demands the use of appropriate wheel hub/Wheel Speed Sensor parts since the front and back sensors are distinct. Place the wheel hub and bearing assembly onto the suspension knuckle before tightening its wheel hub mounting bolts to 130 nm (96 ft. Lbs.). Place the lower Control Arm ball stud back into the suspension knuckle before joining it to the upper Control Arm. Put the Spindle Nut and washer onto the suspension assembly then add the retainer. Thread the outer Tie Rod End onto the suspension knuckle. Reposition the brake rotor and its caliper before docking the speed sensor and shock absorber electrical connections. Add the real-time damping position sensor link if installed before putting on the wheel and tire assembly then lowering the vehicle into place.