How to replace the front brake line on Chevrolet Corvette?

To replace the brake hose of the front wheel: raise and support the vehicle, remove the tire and wheel assembly. Remove any dirt from the brake hose and brake pipe fitting and place a rubber cap or plug on the exposed brake pipe fitting end for the prevention of fluid loss and possible contamination. The brake pipe fitting should be disconnected from the brake hose using a back up wrench and, at the same time, the meeting end of the brake pipe fitting should be covered or stopped up without deforming the brake pipe or bracket. The retainer of brake hose should be removed from the hose bracket before getting the brake hose from the bracket. Then, take out the brake caliper inlet fitting bolt and the brake hose to the caliper, disposing off the left two copper brake hose gaskets that will likely adhere to caliper or hose end. For assembly as part of installation, use new copper brake hose gaskets to assemble with brake caliper inlet fitting bolt commenced then to the brake hose, and assemble this unit to the brake caliper, tightening bolt of 50n.m (37 ft. Lbs.). Secure the brake hose to the hose bracket without kinking or twisting and secure the retainer on the fitting of the brake hose onto the bracket. Take off rubber cap/plug on brake pipe fitting end and hook up brake pipe fitting to brake hose while using back up wrench from which no part can be bent or the bracket/pipes; tighten fitting at 18 nm (13 ft. Lbs.). Lastly, the tire and wheel assembly can be reinstalled, the hydraulic brake system should be bled, and the car should be lowered.

How to Service and Repair the Brake Line on Chevrolet Corvette?

Begin the brake hose/line repair process by getting ready the J 29803-A ISO Flaring Kit and its components. You must install double-walled steel brake pipes to stay safe from brake system breakdown and secure the replacement pipes through their original bolt anchors. Double lap flaring tools provide better pressure resistance than single lap tools so avoid using them for this task. Get the recommended tubing and steel fitting nuts before cutting the tubing to match old pipe length plus 3 mm (1/8 inch) for each ISO flare installation. Begin the work by fitting the hardware onto the tubes before flaring then round both tube edges using a de-burring tool. Thoroughly clean all lubricants from the brake pipe and flaring device. Place the flaring tool into a vise and put on its corresponding collet and forming mandrel. Then place the mandrel into the body of the tool. Move the forcing screw up until it hits the mandrel before stepping it down one rotation. Put the clamping nut over the brake pipe into the collet and position the pipe end just 19 mm (3/4 inch) past the collet face before placing the collet into the tool body. Snug the clamping nut first to keep the brake line inside the tool before turning the forcing screw until it stops. Over-torque could enlarge the flare. Press release the clamping nut to install this setup before removing it along with the collet for use of the new flare. End the new pipe shape according to the original unit but keep a 19 mm (3/4 inch) distance from nearby moving features.

OEM Chevrolet Corvette Brake Line

Brake Hose

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

42 Brake Lines found

View related parts
Chevrolet Corvette Flex Hose, Front Passenger Side Part Number: 85589040
$50.21 MSRP: $89.66
You Save: $39.45 (44%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Hose Assembly-Front Brake; Brake Hose; Hose, Hydraulic Brake
- Position: Front Passenger Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2023-2024 Chevrolet Corvette | Stingray, Z06 | 8 Cyl 5.5 L GAS, 8 Cyl 6.2 L GAS
View related parts
Chevrolet Corvette Flex Hose, Front Passenger Side Part Number: 84688474
$38.98 MSRP: $69.61
You Save: $30.63 (44%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Hose Assembly-Front Brake; Brake Hose; Hose, Hydraulic Brake
- Position: Front Passenger Side
- Replaces: 20988186, 84251375
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2014-2019 Chevrolet Corvette | Grand Sport, Stingray, Z06, ZR1 | 8 Cyl 6.2 L GAS
View related parts
Chevrolet Corvette Flex Hose, Front Driver Side Part Number: 85589039
$50.15 MSRP: $89.56
You Save: $39.41 (44%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Hose Assembly-Front Brake; Brake Hose; Hose, Hydraulic Brake
- Position: Front Driver Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2023-2024 Chevrolet Corvette | Stingray, Z06 | 8 Cyl 5.5 L GAS, 8 Cyl 6.2 L GAS
View related parts
Chevrolet Corvette Flex Hose, Front Driver Side Part Number: 84841275
$21.43 MSRP: $38.26
You Save: $16.83 (44%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Hose Assembly-Front Brake; Hydraulic Hose; Brake Hose; Brake Line
- Position: Front Driver Side
- Replaced by: 85029663
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2020-2024 Chevrolet Corvette | E-Ray, Stingray, Z06 | 8 Cyl 5.5 L GAS, 8 Cyl 6.2 L FULL HYBRID EV-GAS (FHEV), 8 Cyl 6.2 L GAS
View related parts
Chevrolet Corvette Flex Hose, Front Passenger Side Part Number: 84841276
$21.43 MSRP: $38.26
You Save: $16.83 (44%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Hose Assembly-Front Brake; Hydraulic Hose; Brake Hose; Brake Line; Hose, Hydraulic Brake
- Position: Front Passenger Side
- Replaced by: 85029664
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2020-2024 Chevrolet Corvette | E-Ray, Stingray, Z06 | 8 Cyl 5.5 L GAS, 8 Cyl 6.2 L FULL HYBRID EV-GAS (FHEV), 8 Cyl 6.2 L GAS
View related parts
Chevrolet Corvette Flex Hose, Rear Part Number: 19173979
$28.12 MSRP: $50.22
You Save: $22.10 (45%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Hose Assembly, Rear Brake; Hydraulic Hose; Brake Hose; Brake Line
- Position: Rear
- Replaces: 18032753
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1993-1996 Chevrolet Corvette | 40th Anniversary Edition, Base, Collector's Edition, Grand Sport, Indianapolis 500 Pace Car, ZR-1 | 8 Cyl 5.7 L GAS
View related parts
Chevrolet Corvette Flex Hose, Front Part Number: 85589037
$34.37 MSRP: $61.38
You Save: $27.01 (44%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Hose Assembly-Front Brake; Hose, Hydraulic Brake
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2023 Chevrolet Corvette | Stingray, Z06 | 8 Cyl 5.5 L GAS, 8 Cyl 6.2 L GAS
View related parts
Chevrolet Corvette Flex Hose, Front Part Number: 85560988
$49.45 MSRP: $88.30
You Save: $38.85 (44%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Hose Assembly-Front Brake; Hose, Hydraulic Brake
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2023 Chevrolet Corvette | Stingray, Z06 | 8 Cyl 5.5 L GAS, 8 Cyl 6.2 L GAS
View related parts
Chevrolet Corvette Flex Hose, Front Part Number: 86538578
$27.04 MSRP: $48.29
You Save: $21.25 (44%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Hose Assembly-Front Brake; Hose, Hydraulic Brake
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2023 Chevrolet Corvette | Stingray, Z06 | 8 Cyl 5.5 L GAS, 8 Cyl 6.2 L GAS
View related parts
Chevrolet Corvette Flex Hose, Front Part Number: 85560987
$24.88 MSRP: $44.42
You Save: $19.54 (44%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Hose Assembly-Front Brake; Hose, Hydraulic Brake
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2023 Chevrolet Corvette | Stingray, Z06 | 8 Cyl 5.5 L GAS, 8 Cyl 6.2 L GAS
View related parts
Chevrolet Corvette Flex Hose, Front Passenger Side Part Number: 18037192
$27.60 MSRP: $49.28
You Save: $21.68 (44%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Hose Assembly, Front Brake; Hydraulic Hose; Brake Hose; Brake Line
- Position: Front Passenger Side
- Replaces: 17999662
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1994-1996 Chevrolet Corvette | Base, Collector's Edition, Grand Sport, Indianapolis 500 Pace Car, ZR-1 | 8 Cyl 5.7 L GAS
View related parts
Chevrolet Corvette Flex Hose, Front Driver Side Part Number: 19174135
$28.99 MSRP: $51.76
You Save: $22.77 (44%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Hose Assembly, Front Brake; Hydraulic Hose; Brake Hose; Brake Line
- Position: Front Driver Side
- Replaces: 17999661, 18037191
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1994-1996 Chevrolet Corvette | Base, Collector's Edition, Grand Sport, Indianapolis 500 Pace Car, ZR-1 | 8 Cyl 5.7 L GAS
View related parts
Chevrolet Corvette Flex Hose Part Number: 17999556
$14.42 MSRP: $20.64
You Save: $6.22 (31%)
ADD TO CART
Product Specifications
- Other Name: F-Hose Assembly; Hydraulic Hose; Brake Hose; Brake Line
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1993 Chevrolet Corvette | 40th Anniversary Edition, Base, ZR-1 | 8 Cyl 5.7 L GAS
View related parts
Chevrolet Corvette Flex Hose, Front Driver Side Part Number: 84688473
$39.95 MSRP: $71.34
You Save: $31.39 (44%)
Product Specifications
- Other Name: Hose Assembly-Front Brake; Hydraulic Hose; Brake Hose; Brake Line; Hose, Hydraulic Brake
- Position: Front Driver Side
- Replaced by: 85880715
- Replaces: 20988185, 84251374
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2014-2019 Chevrolet Corvette | Grand Sport, Stingray, Z06, ZR1 | 8 Cyl 6.2 L GAS
View related parts
Chevrolet Corvette Flex Hose Part Number: 14076178
Product Specifications
- Other Name: Hose, Hydraulic Brake; Hydraulic Hose; Brake Hose; Brake Line
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1984-1987 Chevrolet Corvette | Base, Indianapolis 500 Pace Car | 8 Cyl 5.7 L GAS
View related parts
Chevrolet Corvette Brake Hose, Rear Driver Side Part Number: 19366776
Product Specifications
- Other Name: Hose Assembly, Rear Brake; Hydraulic Hose; Brake Line; Hose, Hydraulic Brake
- Position: Rear Driver Side
- Replaces: 25998825
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2009-2013 Chevrolet Corvette | 427, ZR1 | 8 Cyl 6.2 L GAS, 8 Cyl 7.0 L GAS
View related parts
Chevrolet Corvette Flex Hose, Passenger Side Part Number: 10097648
Product Specifications
- Other Name: Hose, Hydraulic Brake; Hydraulic Hose; Brake Hose; Brake Line
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1988-1992 Chevrolet Corvette | 35th Anniversary Edition, Base, ZR-1 | 8 Cyl 5.7 L GAS
View related parts
Chevrolet Corvette Flex Hose, Driver Side Part Number: 10097647
Product Specifications
- Other Name: Hose, Hydraulic Brake; Hydraulic Hose; Brake Hose; Brake Line
- Position: Driver Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1988-1992 Chevrolet Corvette | 35th Anniversary Edition, Base, ZR-1 | 8 Cyl 5.7 L GAS
View related parts
Chevrolet Corvette Flex Hose, Driver Side Part Number: 10097649
Product Specifications
- Other Name: Hose, Hydraulic Brake; Hydraulic Hose; Brake Hose; Brake Line
- Position: Driver Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1988-1992 Chevrolet Corvette | 35th Anniversary Edition, Base, ZR-1 | 8 Cyl 5.7 L GAS
View related parts
Chevrolet Corvette Flex Hose, Passenger Side Part Number: 10097650
Product Specifications
- Other Name: Hose, Hydraulic Brake; Hydraulic Hose; Brake Hose; Brake Line
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1988-1992 Chevrolet Corvette | 35th Anniversary Edition, Base, ZR-1 | 8 Cyl 5.7 L GAS

| Page 1 of 3 |Next >

1-20 of 42 Results

Chevrolet Corvette Brake Line

Want to cut long-term maintenance and repair costs? Choose OEM Brake Line. Those parts deliver top durability you can trust. On our site, you'll find a huge catalog of genuine Chevrolet Corvette parts. Prices are unbeatable, so you can keep more in your pocket. Every OEM Chevrolet Corvette Brake Line includes a manufacturer's warranty. You can also get an easy return policy that keeps buying risk free. Fast delivery, get your car on the road quickly. It's simple to search, compare, and order. Stop guessing about quality or fit. Order today and save with parts that last.

The Brake Line is part of the Chevrolet corvette- located in the hydraulic-braking system- translating the amount of pressure applied on the pedal into hydraulic pressure to activate the brake. This is achieved by a system with a master cylinder and a wheel cylinder, Brake Lines and hoses as the means of transferring pressurized brake fluid to the brake pads or shoes. Through the years different Brake Lines have been used in models of Chevrolet Corvette and all of them where intended to provide proper supply of fluid. Any problem in these lines, for example, leaks may drastically affect the braking capability, a characteristic like light-pedal feel or weak brakes. Most of the maintenance tasks for the Chevrolet Corvette's braking system involves the Brake Line, therefore, it is essential to inspect and maintain the system frequently.

Chevrolet Corvette Brake Line Parts and Q&A

Flex Hose
10333773
Q: How to replace the front brake line on Chevrolet Corvette?
A:
To replace the brake hose of the front wheel: raise and support the vehicle, remove the tire and wheel assembly. Remove any dirt from the brake hose and brake pipe fitting and place a rubber cap or plug on the exposed brake pipe fitting end for the prevention of fluid loss and possible contamination. The brake pipe fitting should be disconnected from the brake hose using a back up wrench and, at the same time, the meeting end of the brake pipe fitting should be covered or stopped up without deforming the brake pipe or bracket. The retainer of brake hose should be removed from the hose bracket before getting the brake hose from the bracket. Then, take out the brake caliper inlet fitting bolt and the brake hose to the caliper, disposing off the left two copper brake hose gaskets that will likely adhere to caliper or hose end. For assembly as part of installation, use new copper brake hose gaskets to assemble with brake caliper inlet fitting bolt commenced then to the brake hose, and assemble this unit to the brake caliper, tightening bolt of 50n.m (37 ft. Lbs.). Secure the brake hose to the hose bracket without kinking or twisting and secure the retainer on the fitting of the brake hose onto the bracket. Take off rubber cap/plug on brake pipe fitting end and hook up brake pipe fitting to brake hose while using back up wrench from which no part can be bent or the bracket/pipes; tighten fitting at 18 nm (13 ft. Lbs.). Lastly, the tire and wheel assembly can be reinstalled, the hydraulic brake system should be bled, and the car should be lowered.
Flex Hose, Front
19366737
Q: How to Service and Repair the Brake Line on Chevrolet Corvette?
A:
Begin the brake hose/line repair process by getting ready the J 29803-A ISO Flaring Kit and its components. You must install double-walled steel brake pipes to stay safe from brake system breakdown and secure the replacement pipes through their original bolt anchors. Double lap flaring tools provide better pressure resistance than single lap tools so avoid using them for this task. Get the recommended tubing and steel fitting nuts before cutting the tubing to match old pipe length plus 3 mm (1/8 inch) for each ISO flare installation. Begin the work by fitting the hardware onto the tubes before flaring then round both tube edges using a de-burring tool. Thoroughly clean all lubricants from the brake pipe and flaring device. Place the flaring tool into a vise and put on its corresponding collet and forming mandrel. Then place the mandrel into the body of the tool. Move the forcing screw up until it hits the mandrel before stepping it down one rotation. Put the clamping nut over the brake pipe into the collet and position the pipe end just 19 mm (3/4 inch) past the collet face before placing the collet into the tool body. Snug the clamping nut first to keep the brake line inside the tool before turning the forcing screw until it stops. Over-torque could enlarge the flare. Press release the clamping nut to install this setup before removing it along with the collet for use of the new flare. End the new pipe shape according to the original unit but keep a 19 mm (3/4 inch) distance from nearby moving features.