How to replace the steering knuckle on Chevrolet Equinox?

A replacement Steering Knuckle procedure starts by supporting the vehicle while it is raised then moving on to tire and wheel removal. You should begin by removing the wheel bearing/hub assembly. Take care that the stabilizer link ball stud stays stationary when you remove the link nut before you remove the stabilizer link from the strut assembly. First loosen the Steering Knuckle to strut bolts and nuts before discarding the lower Ball Joint cotter pin while also setting the ball stud nut at the same height as the ball stud top. Insert the j-42188-b Ball Joint separator into the lower Ball Joint-Steering Knuckle connection to disconnect them before you remove the lower Ball Joint nut. Avoid using a pickle fork or wedge-type tool to break free the ball stud to preserve the seal and bushing. Drive out the tie rod from the knuckle followed by installing the Steering Knuckle to strut bolts and nuts and removing the knuckle from the vehicle chassis. Attachment of the Steering Knuckle to the strut assembly includes preliminary bolt and nut tightening on the strut to Steering Knuckle components. Put the lower Ball Joint stud into the Steering Knuckle then begin threading and tighten the ball stud nut to 40 n.m (30 lb ft). Steer the bolts and nuts of the strut to Steering Knuckle until torque reaches 180 n.m (133 lb ft) while avoiding loosening the castle nut for installing the cotter pin. Widen the castle nut until you can install the new cotter pin but avoid letting it touch either the drive axle or Wheel Speed Sensor unit. After tightening the nut for the cotter pin, put a new pin into place. Install the outer Tie Rod End to its position on the knuckle but avoid let the stabilizer link ball stud rotate during link nut installation. Attach the stabilizer shaft link to the strut assembly before torquing the nut to 65 n.m (48 lb ft). First install the new wheel bearing/hub assembly before adding the tire and wheel to the vehicle then lower it and have a wheel alignment completed.

OEM Chevrolet Equinox Steering Knuckle

Front Steering Knuckle

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

18 Steering Knuckles found

View related parts
Chevrolet Equinox Knuckle, Driver Side Part Number: 15837478
$248.07 MSRP: $390.32
You Save: $142.25 (37%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Position: Driver Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2007-2008 Chevrolet Equinox | LS, LT, LTZ, Sport | 6 Cyl 3.4 L GAS, 6 Cyl 3.6 L GAS
View related parts
Chevrolet Equinox Knuckle, Rear Passenger Side Part Number: 87825520
$87.79 MSRP: $150.78
You Save: $62.99 (42%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Knuckle, Rear Wheel
- Position: Rear Passenger Side
- Replaces: 84034348, 84034344
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2018-2024 Chevrolet Equinox | L, LS, LT, Premier, RS | 4 Cyl 1.5 L GAS, 4 Cyl 1.6 L DIESEL, 4 Cyl 2.0 L GAS
View related parts
Chevrolet Equinox Knuckle, Rear Driver Side Part Number: 87825519
$96.25 MSRP: $150.78
You Save: $54.53 (37%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Knuckle, Rear Wheel
- Position: Rear Driver Side
- Replaces: 84034347, 84034343
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2018-2024 Chevrolet Equinox | L, LS, LT, Premier, RS | 4 Cyl 1.5 L GAS, 4 Cyl 1.6 L DIESEL, 4 Cyl 2.0 L GAS
View related parts
Chevrolet Equinox Knuckle, Passenger Side Part Number: 84210077
$51.88 MSRP: $126.56
You Save: $74.68 (60%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Knuckle, Steering
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2018-2024 Chevrolet Equinox | L, LS, LT, Premier, RS | 4 Cyl 1.5 L GAS, 4 Cyl 1.6 L DIESEL, 4 Cyl 2.0 L GAS
View related parts
Chevrolet Equinox Knuckle, Driver Side Part Number: 84210076
$72.98 MSRP: $125.34
You Save: $52.36 (42%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Knuckle, Steering
- Position: Driver Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2018-2024 Chevrolet Equinox | L, LS, LT, Premier, RS | 4 Cyl 1.5 L GAS, 4 Cyl 1.6 L DIESEL, 4 Cyl 2.0 L GAS
View related parts
Chevrolet Equinox Knuckle Part Number: 89047806
Product Specifications
- Other Name: Knuckle, Rear Suspension; Knuckle, Rear Wheel
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2005-2006 Chevrolet Equinox | LS, LT | 6 Cyl 3.4 L GAS
View related parts
Chevrolet Equinox Knuckle Part Number: 89047805
Product Specifications
- Other Name: Knuckle, Rear Suspension; Knuckle, Rear Wheel
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2005-2006 Chevrolet Equinox | LS, LT | 6 Cyl 3.4 L GAS
View related parts
Chevrolet Equinox Knuckle, Rear Passenger Side Part Number: 23343506
Product Specifications
- Other Name: Knuckle, Rear Wheel
- Position: Rear Passenger Side
- Replaces: 22864823, 25927799
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2008-2009 Chevrolet Equinox | LS, LT, LTZ, Sport | 6 Cyl 3.4 L GAS, 6 Cyl 3.6 L GAS
View related parts
Chevrolet Equinox Knuckle, Driver Side Part Number: 22702780
Product Specifications
- Other Name: Knuckle Assembly-Steering; Knuckle, Steering
- Position: Driver Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2005-2006 Chevrolet Equinox | LS, LT | 6 Cyl 3.4 L GAS
View related parts
Chevrolet Equinox Knuckle, Passenger Side Part Number: 22702779
Product Specifications
- Other Name: Knuckle Assembly-Steering; Knuckle, Steering
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2005-2006 Chevrolet Equinox | LS, LT | 6 Cyl 3.4 L GAS
View related parts
Chevrolet Equinox Knuckle, Driver Side Part Number: 15837011
Product Specifications
- Other Name: Knuckle, Steering
- Position: Driver Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2007-2009 Chevrolet Equinox | LS, LT, LTZ, Sport | 6 Cyl 3.4 L GAS, 6 Cyl 3.6 L GAS
View related parts
Chevrolet Equinox Knuckle, Rear Driver Side Part Number: 23337211
$74.91 MSRP: $117.33
You Save: $42.42 (37%)
Product Specifications
- Other Name: Knuckle, Rear Wheel
- Position: Rear Driver Side
- Replaces: 25918954, 22873265
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2008-2017 Chevrolet Equinox | L, LS, LT, LTZ, Premier | 4 Cyl 2.4 L FLEX, 4 Cyl 2.4 L GAS, 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS, 6 Cyl 3.4 L GAS, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS
View related parts
Chevrolet Equinox Knuckle, Rear Passenger Side Part Number: 23337210
$74.91 MSRP: $117.33
You Save: $42.42 (37%)
Product Specifications
- Other Name: Knuckle, Rear Wheel
- Position: Rear Passenger Side
- Replaces: 22873264, 25918953, 25982348
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2008-2017 Chevrolet Equinox | L, LS, LT, LTZ, Premier | 4 Cyl 2.4 L FLEX, 4 Cyl 2.4 L GAS, 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS, 6 Cyl 3.4 L GAS, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS
View related parts
Chevrolet Equinox Knuckle, Driver Side Part Number: 22786979
$214.27 MSRP: $337.14
You Save: $122.87 (37%)
Product Specifications
- Other Name: Knuckle, Steering
- Position: Driver Side
- Replaces: 25978805
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2010-2017 Chevrolet Equinox | L, LS, LT, LTZ, Premier | 4 Cyl 2.4 L FLEX, 4 Cyl 2.4 L GAS, 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS
View related parts
Chevrolet Equinox Knuckle, Passenger Side Part Number: 22786978
$214.27 MSRP: $337.14
You Save: $122.87 (37%)
Product Specifications
- Other Name: Knuckle, Steering
- Position: Passenger Side
- Replaces: 25978806
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2010-2017 Chevrolet Equinox | L, LS, LT, LTZ, Premier | 4 Cyl 2.4 L FLEX, 4 Cyl 2.4 L GAS, 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS
View related parts
Chevrolet Equinox Knuckle, Passenger Side Part Number: 15837479
Product Specifications
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2007 Chevrolet Equinox | LS, LT | 6 Cyl 3.4 L GAS
View related parts
Chevrolet Equinox Knuckle, Passenger Side Part Number: 15837014
Product Specifications
- Other Name: Knuckle, Steering
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2007-2009 Chevrolet Equinox | LS, LT, LTZ, Sport | 6 Cyl 3.4 L GAS, 6 Cyl 3.6 L GAS
View related parts
Chevrolet Equinox Knuckle, Rear Driver Side Part Number: 23343507
$294.49 MSRP: $463.36
You Save: $168.87 (37%)
Product Specifications
- Other Name: Knuckle, Rear Wheel
- Position: Rear Driver Side
- Replaces: 22864824, 25937773
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2008-2009 Chevrolet Equinox | LS, LT, LTZ, Sport | 6 Cyl 3.4 L GAS, 6 Cyl 3.6 L GAS

Chevrolet Equinox Steering Knuckle

Want to cut long-term maintenance and repair costs? Choose OEM Steering Knuckle. Those parts deliver top durability you can trust. On our site, you'll find a huge catalog of genuine Chevrolet Equinox parts. Prices are unbeatable, so you can keep more in your pocket. Every OEM Chevrolet Equinox Steering Knuckle includes a manufacturer's warranty. You can also get an easy return policy that keeps buying risk free. Fast delivery, get your car on the road quickly. It's simple to search, compare, and order. Stop guessing about quality or fit. Order today and save with parts that last.

The Steering Knuckle of Chevrolet Equinox vehicles is still a control arm link that joins the front wheels with the suspension and steering assemblies. It is the place where control arms, tie rod ends and spindle or hubs to which the wheels are fixed are attached. Depending on the type of the drivetrain, the Knuckle may contain an integral spindle or just the hub with the roller bearing in form of tapered ones. In term of suspension, the transition from kingpins to ball joints is seen in steering knuckles to prove innovation of the equipment. An example of the function of the Knuckle is during replacing of ball joints or tie-rod ends, thus, constant check up of the Knuckle is often advised.

Chevrolet Equinox Steering Knuckle Parts Questions & Experts Answers

Knuckle, Rear Passenger Side
23337210
Q: How to replace the steering knuckle on Chevrolet Equinox?
A:
A replacement Steering Knuckle procedure starts by supporting the vehicle while it is raised then moving on to tire and wheel removal. You should begin by removing the wheel bearing/hub assembly. Take care that the stabilizer link ball stud stays stationary when you remove the link nut before you remove the stabilizer link from the strut assembly. First loosen the Steering Knuckle to strut bolts and nuts before discarding the lower Ball Joint cotter pin while also setting the ball stud nut at the same height as the ball stud top. Insert the j-42188-b Ball Joint separator into the lower Ball Joint-Steering Knuckle connection to disconnect them before you remove the lower Ball Joint nut. Avoid using a pickle fork or wedge-type tool to break free the ball stud to preserve the seal and bushing. Drive out the tie rod from the knuckle followed by installing the Steering Knuckle to strut bolts and nuts and removing the knuckle from the vehicle chassis. Attachment of the Steering Knuckle to the strut assembly includes preliminary bolt and nut tightening on the strut to Steering Knuckle components. Put the lower Ball Joint stud into the Steering Knuckle then begin threading and tighten the ball stud nut to 40 n.m (30 lb ft). Steer the bolts and nuts of the strut to Steering Knuckle until torque reaches 180 n.m (133 lb ft) while avoiding loosening the castle nut for installing the cotter pin. Widen the castle nut until you can install the new cotter pin but avoid letting it touch either the drive axle or Wheel Speed Sensor unit. After tightening the nut for the cotter pin, put a new pin into place. Install the outer Tie Rod End to its position on the knuckle but avoid let the stabilizer link ball stud rotate during link nut installation. Attach the stabilizer shaft link to the strut assembly before torquing the nut to 65 n.m (48 lb ft). First install the new wheel bearing/hub assembly before adding the tire and wheel to the vehicle then lower it and have a wheel alignment completed.