How to replace the ABS Control Module with JL4 on Chevrolet HHR?

To replace brake pressure modulator valve (BPMV) with jl4, the Ignition Switch should be off when disconnecting the wiring harness connector from ebcm/ebtcm in order to prevent damage. Start with the removal of the cover from the ecm and tcm, and subsequently, clean ebcm to bpmv area and also brake pipe fittings. After that, disconnect the ebcm electrical connector, master cylinder primary and secondary brake pipe fittings and capping and plugging the bpmv inlet port to avoid fluid loss. Then, remove the lf, rf, rr, and lr brake pipe fittings, capping, and plugging the bpmv outlet port of each to prevent contamination. Pull off the bpmv bolt and gently raise the brake control module assembly straight off the bpmv bracket insulators without prying on the accumulator covers. If a new bpmv is to be installed then ebcm has to be removed. For installation, for a new used bpmv, install ebcm and attach brake control module assembly to the bpmv bracket, making sure that the mounting pins are fully admitted. Use bpmv bolt and tighten it to 11n/97lb in. Connect the lr, rr, rf, lf, master cylinder secondary and primary brake pipe fittings tighten to -21 nm (15 lb ft). Reconnect the ebcm connect, replace ecm and tcm covers, and bleed hydraulic brake system. Program the ebcm and carry out a diagnostic system check - vehicle. After the check, take note of the brake pedal feel; in case it is spongy, do the antilock brake system automated bleed procedure.

OEM Chevrolet HHR ABS Control Module

Anti Lock Brake Control Module

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

6 ABS Control Modules found

View related parts
Chevrolet HHR Control Module
Part Number: 20827128
$310.51 MSRP: $556.94
You Save: $246.43 (45%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Module Kit-Electronic Brake Control; ABS Control Module; Modulator; Module Kit, Electronic Brake Control
- Replaces: 25911087
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2009-2010 Chevrolet HHR | LS, LS Panel, LT, LT Panel, SS, SS Panel | 4 Cyl 2.0 L GAS, 4 Cyl 2.2 L FLEX, 4 Cyl 2.4 L FLEX
View related parts
Chevrolet HHR Control Module
Part Number: 25826700
$197.22 MSRP: $364.90
You Save: $167.68 (46%)
ADD TO CART
Product Specifications
- Other Name: Module Kit-Electronic Brake & Traction Control; ABS Control Module; Module Kit, Electronic Brake Control
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2008 Chevrolet HHR | LS, LS Panel, LT, LT Panel, SS | 4 Cyl 2.0 L GAS, 4 Cyl 2.2 L GAS, 4 Cyl 2.4 L GAS
View related parts
Chevrolet HHR Control Module
Part Number: 15870922
Product Specifications
- Other Name: Module Kit-Electronic Brake & Traction Control; ABS Control Module; Modulator; Module Kit, Electronic Brake Control
- Replaces: 15233333
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2006-2008 Chevrolet HHR | LS, LS Panel, LT, LT Panel, SS | 4 Cyl 2.0 L GAS, 4 Cyl 2.2 L GAS, 4 Cyl 2.4 L GAS
View related parts
Chevrolet HHR Control Module
Part Number: 20827127
$321.20 MSRP: $576.12
You Save: $254.92 (45%)
Product Specifications
- Other Name: Module Kit-Electronic Brake Control; ABS Control Module; Modulator; Module Kit, Electronic Brake Control
- Replaces: 25907539
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2009-2011 Chevrolet HHR | LS, LS Panel, LT, LT Panel, SS, SS Panel | 4 Cyl 2.0 L GAS, 4 Cyl 2.2 L FLEX, 4 Cyl 2.4 L FLEX
View related parts
Chevrolet HHR Control Module
Part Number: 19301486
$373.81 MSRP: $670.56
You Save: $296.75 (45%)
Product Specifications
- Other Name: Valve Kit, Brake Pressure Mode; ABS Control Module; Modulator Valve; Modulator; Valve Kit, Electronic Brake Control
- Replaces: 25798971
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2008-2011 Chevrolet HHR | LS, LS Panel, LT, LT Panel, SS, SS Panel | 4 Cyl 2.0 L GAS, 4 Cyl 2.2 L FLEX, 4 Cyl 2.2 L GAS, 4 Cyl 2.4 L FLEX, 4 Cyl 2.4 L GAS
View related parts
Chevrolet HHR Control Module
Part Number: 25877767
Product Specifications
- Other Name: Valve Assembly-Brake Pressure Mod (W/ Electronic Brake; ABS Control Module; Modulator Valve
- Replaced by: 19301487
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2008 Chevrolet HHR | LS, LS Panel, LT, LT Panel, SS | 4 Cyl 2.0 L GAS, 4 Cyl 2.2 L GAS, 4 Cyl 2.4 L GAS

Chevrolet HHR ABS Control Module

Our website offers an extensive catalog of genuine Chevrolet HHR ABS Control Module at unbeatable prices. Every OEM Chevrolet HHR ABS Control Module comes with a manufacturer's warranty, an easy return policy, and rapid delivery service. Don't miss out on this great opportunity!

Chevrolet HHR ABS Control Module Parts Questions & Experts Answers

Control Module
20827128
Q: How to replace the ABS Control Module with JL4 on Chevrolet HHR?
A: To replace brake pressure modulator valve (BPMV) with jl4, the Ignition Switch should be off when disconnecting the wiring harness connector from ebcm/ebtcm in order to prevent damage. Start with the removal of the cover from the ecm and tcm, and subsequently, clean ebcm to bpmv area and also brake pipe fittings. After that, disconnect the ebcm electrical connector, master cylinder primary and secondary brake pipe fittings and capping and plugging the bpmv inlet port to avoid fluid loss. Then, remove the lf, rf, rr, and lr brake pipe fittings, capping, and plugging the bpmv outlet port of each to prevent contamination. Pull off the bpmv bolt and gently raise the brake control module assembly straight off the bpmv bracket insulators without prying on the accumulator covers. If a new bpmv is to be installed then ebcm has to be removed. For installation, for a new used bpmv, install ebcm and attach brake control module assembly to the bpmv bracket, making sure that the mounting pins are fully admitted. Use bpmv bolt and tighten it to 11n/97lb in. Connect the lr, rr, rf, lf, master cylinder secondary and primary brake pipe fittings tighten to -21 nm (15 lb ft). Reconnect the ebcm connect, replace ecm and tcm covers, and bleed hydraulic brake system. Program the ebcm and carry out a diagnostic system check - vehicle. After the check, take note of the brake pedal feel; in case it is spongy, do the antilock brake system automated bleed procedure.