How to replace the rear brake caliper bracket on the 1500 Series on Chevrolet Silverado 1500 Classic?

Before handling the 1500 series Brake Caliper Bracket replacement start by checking the brake master cylinder reservoir fluid. If the fluid rests in the center of its range no draining is needed but lowering the level to midpoint when the fluid is above the center mark. Put the brake caliper pistons into complete retraction through the use of a c-clamp placed over the housing top onto caliper backing. Tighten the clamp over the top of the caliper housing against the back of the outboard pad when the pistons reach their fully depressed position. Use heavy mechanic's wire to hold the caliper when you untie its bolts and take it away from the bracket. Avoid disconnecting the hydraulic hose during this step. Take out the brake pads and clips first then uninstall the Brake Caliper Bracket bolts to remove the entire bracket. Discard all contaminants from inside both Brake Caliper Bracket ends then check the mounting surface and threads for cleanliness. Set the Brake Caliper Bracket in place after cleansing both the threads and original adhesive surface while applying threadlocker gm p/n 12345493 (Canadian P/N 10953488) to the threads. Secure the Brake Caliper Bracket bolts at 200 nm (148 ft. Lbs.) torque and put on anti-rattle clips followed by brake pads. Run the caliper through its bracket and bolt it into position with 42 nm torque setting before placing the tire and wheel assembly back. Turn off the engine and press the brake pedal to its 2/3rds mark then release slowly to accomplish the pad and caliper piston bedding process. Put fresh brake fluid into the reservoir when required to reach the proper fluid level.

OEM Chevrolet Silverado 1500 Classic Brake Caliper Bracket

Caliper Bracket

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

6 Brake Caliper Brackets found

View related parts
Chevrolet Silverado 1500 Classic Caliper Bracket, Passenger Side
Part Number: 25997055
$127.26 MSRP: $246.98
You Save: $119.72 (49%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bracket Kit-Front Brake Caliper; Brake Caliper Bracket; Caliper Support; Bracket; Bracket Kit, Wheel Brake Cylinder/Caliper
- Position: Passenger Side
- Replaces: 18040094
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2007 Chevrolet Silverado 1500 Classic | LS, LT, SS, WT | 6 Cyl 4.3 L GAS, 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L GAS
View related parts
Chevrolet Silverado 1500 Classic Caliper Bracket, Driver Side
Part Number: 25997053
$142.64 MSRP: $255.84
You Save: $113.20 (45%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bracket Kit-Front Brake Caliper; Brake Caliper Bracket; Caliper Support; Bracket; Bracket Kit, Wheel Brake Cylinder/Caliper
- Position: Driver Side
- Replaces: 18040093
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2007 Chevrolet Silverado 1500 Classic | LS, LT, SS, WT | 6 Cyl 4.3 L GAS, 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L GAS
View related parts
Chevrolet Silverado 1500 Classic Caliper Bracket, Silver
Part Number: 23498371
$62.47 MSRP: $125.42
You Save: $62.95 (51%)
ADD TO CART
Product Specifications
- Other Name: Bracket Kit-Front Brake Caliper *Silver; Brake Caliper Bracket; Caliper Support; Bracket
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2007 Chevrolet Silverado 1500 Classic | LS, LT, SS, WT | 6 Cyl 4.3 L GAS, 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L GAS
View related parts
Chevrolet Silverado 1500 Classic Caliper Bracket, Rear
Part Number: 25997047
Product Specifications
- Other Name: Bracket Kit-Rear Brake Caliper; Brake Caliper Bracket; Mount Bracket; Caliper Mount; Caliper Support; Bracket; Bracket Kit, Wheel Brake Cylinder/Caliper
- Position: Rear
- Replaces: 18040099
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2007 Chevrolet Silverado 1500 Classic | Hybrid, LS, LT, SS, WT | 6 Cyl 4.3 L GAS, 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L FULL HYBRID EV-GAS (FHEV), 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L GAS
View related parts
Chevrolet Silverado 1500 Classic Caliper Mount
Part Number: 18048917
Product Specifications
- Other Name: Bracket, Wheel Brake Cylinder/Caliper; Brake Caliper Bracket
- Position: Rear
- Replaces: 18048082
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2007 Chevrolet Silverado 1500 Classic | Hybrid | 8 Cyl 5.3 L FULL HYBRID EV-GAS (FHEV)
View related parts
Chevrolet Silverado 1500 Classic Caliper Bracket, Rear
Part Number: 25997048
Product Specifications
- Other Name: Bracket Kit-Rear Brake Caliper; Brake Caliper Bracket; Mount Bracket; Caliper Mount; Caliper Support; Bracket; Bracket Kit, Wheel Brake Cylinder/Caliper
- Position: Rear
- Replaces: 18040098
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2007 Chevrolet Silverado 1500 Classic | Hybrid, LS, LT, SS, WT | 6 Cyl 4.3 L GAS, 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L FULL HYBRID EV-GAS (FHEV), 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L GAS

Chevrolet Silverado 1500 Classic Brake Caliper Bracket

Our website offers an extensive catalog of genuine Chevrolet Silverado 1500 Classic Brake Caliper Bracket at unbeatable prices. Every OEM Chevrolet Silverado 1500 Classic Brake Caliper Bracket comes with a manufacturer's warranty, an easy return policy, and rapid delivery service. Don't miss out on this great opportunity!

Chevrolet Silverado 1500 Classic Brake Caliper Bracket Parts Questions & Experts Answers

Caliper Bracket, Driver Side
25997053
Q: How to replace the rear brake caliper bracket on the 1500 Series on Chevrolet Silverado 1500 Classic?
A: Before handling the 1500 series Brake Caliper Bracket replacement start by checking the brake master cylinder reservoir fluid. If the fluid rests in the center of its range no draining is needed but lowering the level to midpoint when the fluid is above the center mark. Put the brake caliper pistons into complete retraction through the use of a c-clamp placed over the housing top onto caliper backing. Tighten the clamp over the top of the caliper housing against the back of the outboard pad when the pistons reach their fully depressed position. Use heavy mechanic's wire to hold the caliper when you untie its bolts and take it away from the bracket. Avoid disconnecting the hydraulic hose during this step. Take out the Brake Pads and clips first then uninstall the Brake Caliper Bracket bolts to remove the entire bracket. Discard all contaminants from inside both Brake Caliper Bracket ends then check the mounting surface and threads for cleanliness. Set the Brake Caliper Bracket in place after cleansing both the threads and original adhesive surface while applying threadlocker gm p/n 12345493 (Canadian P/N 10953488) to the threads. Secure the Brake Caliper Bracket bolts at 200 nm (148 ft. Lbs.) torque and put on anti-rattle clips followed by brake pads. Run the caliper through its bracket and bolt it into position with 42 nm torque setting before placing the tire and wheel assembly back. Turn off the engine and press the brake pedal to its 2/3rds mark then release slowly to accomplish the pad and caliper piston bedding process. Put fresh brake fluid into the reservoir when required to reach the proper fluid level.