How to replace the RH engine mount and engine mount bracket on Chevrolet Trailblazer?

The first step to replace the right engine mount and bracket is disconnecting the battery negative cable. Disconnect the electrical connector of the Fan Clutch. The Fan Clutch remover and installer (J 46406) should be used to disconnect the cooling Fan Clutch from the Water Pump Pulley before leaving it free inside the fan shroud. The procedure begins by disconnecting the MAP Sensor electrical connector and its retainer after which follows MAP Sensor removal. The right shock module should be removed if the frame engine mount will be taken out. Raise the vehicle after you remove the nuts securing upper right and left engine mount points. Unfasten the right and left lower engine mount nuts and also remove the engine protection shield. When installing a jack against the Oil Pan prevent hitting the oil level sender with the equipment. Apply a floor jack on the Oil Pan using wood while lowering the vehicle until the engine clears the mount studs. Separate the right engine mount from its bracket while noting where it encountered the heat shield during installation before you remove both bracket bolts and the mount bracket itself. Additionally remove the right frame engine mount bracket bolts and the bracket from service. Keep the right frame engine mount bracket in place then install it before tightening bolts to 110 n.m (81 lb ft). After placing the right engine mount bracket into position you must attach it with bolts and tighten them to 50 n.m (37 lb ft). Position the right engine mount correctly while maintaining the heat shield position above the anti-rotation feature. Lower down the engine until it rests on engine mounts then install right and left upper engine mount nuts while torquing them to 70 n.m (52 lb ft). Place the engine protection shield on and fasten it with bolts when the vehicle is raised from the floor. The technician installs right and left lower engine mount nuts while tightening them to 70 n.m (52 lb ft). The vehicle must then be lowered. To finalize installation mount the right shock module and attach the MAP Sensor alongside its MAP Sensor retainer and electrical connector then use Fan Clutch remover and installer (J 46406) to attach the cooling Fan Clutch to the Water Pump Pulley. Reconnect the battery negative cable while connecting the electrical Fan Clutch connector.

OEM Chevrolet Trailblazer Engine Mount Bracket

Engine Mount

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

16 Engine Mount Brackets found

View related parts
Chevrolet Trailblazer Strut Bracket Part Number: 60006233
$29.38 MSRP: $46.02
You Save: $16.64 (37%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bracket, Transmission Mounting Support; Transmission Mount Bracket
- Replaces: 42481300
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2021-2024 Chevrolet Trailblazer | ACTIV, L, LS, LT, RS | 3 Cyl 1.2 L GAS, 3 Cyl 1.3 L GAS
View related parts
Chevrolet Trailblazer Motor Mount Part Number: 60003412
$85.75 MSRP: $134.31
You Save: $48.56 (37%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Mount, Engine Mounting; Engine Mount Bracket; Side Mount
- Replaced by: 60006090
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2021-2024 Chevrolet Trailblazer | ACTIV, LS, LT, RS | 3 Cyl 1.3 L GAS
View related parts
Chevrolet Trailblazer Motor Mount Part Number: 60003411
$87.01 MSRP: $136.30
You Save: $49.29 (37%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Mount, Engine Mounting; Engine Mount Bracket; Side Mount
- Replaced by: 60005993
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2021-2023 Chevrolet Trailblazer | ACTIV, L, LS, LT, RS | 3 Cyl 1.2 L GAS, 3 Cyl 1.3 L GAS
View related parts
Chevrolet Trailblazer Motor Mount Bracket Part Number: 88964337
$83.88 MSRP: $149.38
You Save: $65.50 (44%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bracket, Engine Mounting; Engine Mount Bracket; Motor Mount
- Replaces: 15079400
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2002-2009 Chevrolet Trailblazer | Base, LS, LT, LTZ, North Face | 6 Cyl 4.2 L GAS
View related parts
Chevrolet Trailblazer Motor Mount Bracket Part Number: 88964338
$92.01 MSRP: $144.12
You Save: $52.11 (37%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Bracket, Engine Mounting; Engine Mount Bracket; Motor Mount
- Replaces: 15079401
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2002-2009 Chevrolet Trailblazer | Base, LS, LT, LTZ, North Face | 6 Cyl 4.2 L GAS
View related parts
Chevrolet Trailblazer Motor Mount Part Number: 60005993
$87.01 MSRP: $136.30
You Save: $49.29 (37%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Mount, Engine Mounting; Mount, Engine
- Replaces: 60003411
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2021-2024 Chevrolet Trailblazer | ACTIV, L, LS, LT, RS | 3 Cyl 1.2 L GAS, 3 Cyl 1.3 L GAS
View related parts
Chevrolet Trailblazer Mount Support Part Number: 60002825
$64.68 MSRP: $101.32
You Save: $36.64 (37%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Bracket-Engine Mount Engine Side; Engine Mount Bracket; Motor Mount; Bracket, Engine Mounting
- Replaced by: 60006668
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2021-2024 Chevrolet Trailblazer | L, LS, LT | 3 Cyl 1.2 L GAS
View related parts
Chevrolet Trailblazer Mount Support Part Number: 60002266
$63.20 MSRP: $99.01
You Save: $35.81 (37%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Bracket-Engine Mount Engine Side; Engine Mount Bracket; Motor Mount; Bracket, Engine Mounting
- Replaced by: 60006091
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2021-2024 Chevrolet Trailblazer | ACTIV, LS, LT, RS | 3 Cyl 1.3 L GAS
View related parts
Chevrolet Trailblazer Mount Bracket Part Number: 55512875
$21.92 MSRP: $34.33
You Save: $12.41 (37%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Brace, Engine Mounting; Engine Mount Bracket; Motor Mount
- Replaced by: 55515910
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2021-2024 Chevrolet Trailblazer | L, LS, LT | 3 Cyl 1.2 L GAS
View related parts
Chevrolet Trailblazer Support Brace Part Number: 42481285
$5.94 MSRP: $9.31
You Save: $3.37 (37%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Brace, Engine Mounting; Motor Mount
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2021-2024 Chevrolet Trailblazer | ACTIV, L, LS, LT, RS | 3 Cyl 1.2 L GAS, 3 Cyl 1.3 L GAS
View related parts
Chevrolet Trailblazer Motor Mount, Front Part Number: 15255897
Product Specifications
- Other Name: Front Mount; Engine Mount Bracket; Mount
- Position: Front
- Replaces: 15237337
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2006-2009 Chevrolet Trailblazer | SS | 8 Cyl 6.0 L GAS
View related parts
Chevrolet Trailblazer Motor Mount Bracket, Passenger Side Part Number: 15062380
Product Specifications
- Other Name: Bracket, Engine Mounting
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2002-2009 Chevrolet Trailblazer | Base, LS, LT, LTZ, North Face | 6 Cyl 4.2 L GAS
View related parts
Chevrolet Trailblazer Motor Mount Bracket, Driver Side Part Number: 15062379
$100.58 MSRP: $157.55
You Save: $56.97 (37%)
Product Specifications
- Other Name: Bracket, Engine Mounting
- Position: Driver Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2002-2009 Chevrolet Trailblazer | Base, LS, LT, LTZ, North Face | 6 Cyl 4.2 L GAS
View related parts
Chevrolet Trailblazer Motor Mount, Front Part Number: 15255898
Product Specifications
- Other Name: Front Mount; Engine Mount Bracket; Mount
- Position: Front
- Replaces: 15237338
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2006-2009 Chevrolet Trailblazer | SS | 8 Cyl 6.0 L GAS
View related parts
Chevrolet Trailblazer Motor Mount, Front Driver Side Part Number: 15788794
$179.37 MSRP: $282.21
You Save: $102.84 (37%)
Product Specifications
- Other Name: Front Mount; Engine Mount Bracket; Mount
- Position: Front Driver Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2006-2008 Chevrolet Trailblazer | Base, LS, LT | 8 Cyl 5.3 L GAS
View related parts
Chevrolet Trailblazer Motor Mount, Front Passenger Side Part Number: 15788793
$170.87 MSRP: $268.88
You Save: $98.01 (37%)
Product Specifications
- Other Name: Front Mount; Engine Mount Bracket; Mount
- Position: Front Passenger Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2006-2008 Chevrolet Trailblazer | Base, LS, LT | 8 Cyl 5.3 L GAS

Chevrolet Trailblazer Engine Mount Bracket

Want to cut long-term maintenance and repair costs? Choose OEM Engine Mount Bracket. Those parts deliver top durability you can trust. On our site, you'll find a huge catalog of genuine Chevrolet Trailblazer parts. Prices are unbeatable, so you can keep more in your pocket. Every OEM Chevrolet Trailblazer Engine Mount Bracket includes a manufacturer's warranty. You can also get an easy return policy that keeps buying risk free. Fast delivery, get your car on the road quickly. It's simple to search, compare, and order. Stop guessing about quality or fit. Order today and save with parts that last.

The Chevrolet Trailblazer Engine Mount Bracket stands as a critical component that demonstrates reliability features in all Chevrolet Trailblazer models. The Engine Mount Bracket functions to reduce engine noise and vibration and establishes engine position inside the chassis which greatly boosts driving comfort together with vehicle safety. Engine Mount Bracket components fit Chevrolet Trailblazer models through utilization of standard metal construction with rubber suspension elements and hydraulic shock absorbers and electronic mount technology which changes stiffness at different engine speeds. Through these design features the system enhances efficiency and provides better driving control in addition to performance enhancement. Since its introduction the Chevrolet Trailblazer has progressed through different generations which caused the Engine Mount Bracket to shift according to changing engine requirements. Routine checks of the Engine Mount Bracket remain important because both time-related degradation and exposure to high temperatures and leaking fluids will affect its durability and potential breakdown. The Chevrolet Trailblazer Engine Mount Bracket excels in automotive markets because of its durable design and its dedication to safety performance thus becoming vital in the vehicle's engineering. The Engine Mount Bracket of the Chevrolet Trailblazer continues to maintain its status as a premier choice in terms of vehicle reliability because of its confirmed reliability and ground-breaking design elements.

Chevrolet Trailblazer Engine Mount Bracket Parts Questions & Experts Answers

Motor Mount, Front Passenger Side
15788793
Q: How to replace the RH engine mount and engine mount bracket on Chevrolet Trailblazer?
A:
The first step to replace the right engine mount and bracket is disconnecting the battery negative cable. Disconnect the electrical connector of the Fan Clutch. The Fan Clutch remover and installer (J 46406) should be used to disconnect the cooling Fan Clutch from the Water Pump Pulley before leaving it free inside the fan shroud. The procedure begins by disconnecting the MAP Sensor electrical connector and its retainer after which follows MAP Sensor removal. The right shock module should be removed if the frame engine mount will be taken out. Raise the vehicle after you remove the nuts securing upper right and left engine mount points. Unfasten the right and left lower engine mount nuts and also remove the engine protection shield. When installing a jack against the Oil Pan prevent hitting the oil level sender with the equipment. Apply a floor jack on the Oil Pan using wood while lowering the vehicle until the engine clears the mount studs. Separate the right engine mount from its bracket while noting where it encountered the heat shield during installation before you remove both bracket bolts and the mount bracket itself. Additionally remove the right frame engine mount bracket bolts and the bracket from service. Keep the right frame engine mount bracket in place then install it before tightening bolts to 110 n.m (81 lb ft). After placing the right engine mount bracket into position you must attach it with bolts and tighten them to 50 n.m (37 lb ft). Position the right engine mount correctly while maintaining the heat shield position above the anti-rotation feature. Lower down the engine until it rests on engine mounts then install right and left upper engine mount nuts while torquing them to 70 n.m (52 lb ft). Place the engine protection shield on and fasten it with bolts when the vehicle is raised from the floor. The technician installs right and left lower engine mount nuts while tightening them to 70 n.m (52 lb ft). The vehicle must then be lowered. To finalize installation mount the right shock module and attach the MAP Sensor alongside its MAP Sensor retainer and electrical connector then use Fan Clutch remover and installer (J 46406) to attach the cooling Fan Clutch to the Water Pump Pulley. Reconnect the battery negative cable while connecting the electrical Fan Clutch connector.