How to service and ensure proper assembly of brake calipers on GMC C2500?

Change all of the items in the service and repair kit and do not forget to lubricate the rubber parts with clean brake fluid before assembling. After any components are removed or unplugged, bleeding the brake system may be needed and brake pads need to be replaced inside every axle set only. Refer to the torque values for unlubricated fasteners and perform your work in a bench that does not contain any mineral oil substances. Try not to hold your fingers where the Piston is located to avoid getting hurt. The first step is to take off the brake caliper from the vehicle. Set a hardwood piece in front of the Piston for protection and then slide the Piston out by blowing air through the brake hose inlet fitting of the brake caliper's body. Following this, you should pull out the Piston boot, the Piston seal, bleed screw cap and the bleed screw. Check for any surface damage or rust on the brake caliper bore and on the groove for the Piston seal and if serious damage is noted, replace the caliper housing. Examine the guide surfaces of the brake caliper bracket for rust and damage and swap the bracket if you notice any signs of wear or rust. Remove any residue from the parts of the Brake Pad guiding surfaces on the brake caliper housing and mounting bracket and clean and dry all other parts with denatured alcohol after drying with air. Make sure every passage inside the brake caliper housing and the brake caliper bleeder valve has been blown out. The next step is to put in the bleed screw and tighten it to 12 n.m (106 lb in) before fitting the bleed screw cap. Pour brake fluid onto both the new Piston seal and the brake caliper bore groove before putting the seal into place, making sure it does not twist. Apply brake fluid to the brake caliper bore and to the Piston and then install the boot and Piston with the boot fitting snugly into both. Give the additional Piston the same treatment and reassemble it as well. The last step is to secure the brake caliper back to the vehicle.

OEM GMC C2500 Brake Calipers

Caliper

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

15 Brake Calipers found

View related parts
GMC C2500 Caliper, Front Driver Side Part Number: 19140905
$36.34 MSRP: $65.76
You Save: $29.42 (45%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper Assembly, Front Brake (W/O Brake Pads) (Remanufacture); Brake Caliper; Caliper, Wheel Brake Cylinder/Caliper
- Position: Front Driver Side
- Replaces: 18021453, 18036666
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1985-1986 GMC C2500 | Base, High Sierra, Sierra Classic | 6 Cyl 4.3 L GAS, 6 Cyl 4.8 L GAS, 8 Cyl 5.0 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 6.2 L DIESEL, 8 Cyl 7.4 L GAS
View related parts
GMC C2500 Caliper, Front Passenger Side Part Number: 19140904
$40.34 MSRP: $73.08
You Save: $32.74 (45%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper Assembly, Front Brake (W/O Brake Pads) (Remanufacture); Brake Caliper; Caliper, Wheel Brake Cylinder/Caliper
- Position: Front Passenger Side
- Replaces: 18021454, 18036665
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1985-1986 GMC C2500 | Base, High Sierra, Sierra Classic | 6 Cyl 4.3 L GAS, 6 Cyl 4.8 L GAS, 8 Cyl 5.0 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 6.2 L DIESEL, 8 Cyl 7.4 L GAS
View related parts
GMC C2500 Overhaul Kit, Front Part Number: 18031633
$8.47 MSRP: $15.12
You Save: $6.65 (44%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper Kit, Front Brake; Brake Caliper Repair Kit; Disc Brake Hardware Kit; Caliper Kit, Wheel Cylinder Piston
- Position: Front
- Replaces: 18014743
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1988-1990 GMC C2500 | Sierra, Sierra SLE, Sierra SLX | 6 Cyl 4.3 L GAS, 8 Cyl 5.0 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 6.2 L DIESEL
View related parts
GMC C2500 Caliper, Front Passenger Side Part Number: 19140914
$40.48 MSRP: $73.47
You Save: $32.99 (45%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper Assembly, Front Brake (W/O Brake Pads) (Remanufacture); Brake Caliper; Caliper, Wheel Brake Cylinder/Caliper
- Position: Front Passenger Side
- Replaces: 18021435, 18036671
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1984-1986 GMC C2500 | Base, High Sierra, Sierra Classic | 6 Cyl 4.1 L GAS, 6 Cyl 4.3 L GAS, 6 Cyl 4.8 L GAS, 8 Cyl 5.0 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 6.2 L DIESEL, 8 Cyl 7.4 L GAS
View related parts
GMC C2500 Caliper, Front Driver Side Part Number: 19140995
$45.85 MSRP: $83.62
You Save: $37.77 (46%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper Assembly, Front Brake (W/O Brake Pads) (Remanufacture); Brake Caliper; Caliper, Wheel Brake Cylinder/Caliper
- Position: Front Driver Side
- Replaces: 18014741, 18036603
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1988-1991 GMC C2500 | Sierra, Sierra SLE, Sierra SLX | 6 Cyl 4.3 L GAS, 8 Cyl 5.0 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 6.2 L DIESEL, 8 Cyl 7.4 L GAS
View related parts
GMC C2500 Caliper, Front Passenger Side Part Number: 19140994
$58.54 MSRP: $106.85
You Save: $48.31 (46%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper Assembly, Front Brake (W/O Brake Pads) (Remanufacture); Brake Caliper; Caliper, Wheel Brake Cylinder/Caliper
- Position: Front Passenger Side
- Replaces: 18014742, 18036602
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1988-1991 GMC C2500 | Sierra, Sierra SLE, Sierra SLX | 6 Cyl 4.3 L GAS, 8 Cyl 5.0 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 6.2 L DIESEL, 8 Cyl 7.4 L GAS
View related parts
GMC C2500 Caliper, Passenger Side Part Number: 19242899
Product Specifications
- Other Name: Caliper, Wheel Brake Cylinder/Caliper; Brake Caliper; Housing, Wheel Brake Cylinder/Caliper
- Position: Passenger Side
- Replaces: 14002544, 15665668
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1991-2000 GMC C2500 | Sierra, Sierra SL, Sierra SLE, Sierra SLT, Sierra SLX | 6 Cyl 4.3 L GAS, 8 Cyl 5.0 L GAS, 8 Cyl 5.7 L CNG, 8 Cyl 5.7 L GAS, 8 Cyl 6.2 L DIESEL, 8 Cyl 6.5 L DIESEL, 8 Cyl 7.4 L GAS
View related parts
GMC C2500 Caliper, Driver Side Part Number: 19242898
Product Specifications
- Other Name: Caliper, Wheel Brake Cylinder/Caliper; Brake Caliper; Housing, Wheel Brake Cylinder/Caliper
- Position: Driver Side
- Replaces: 14002543, 15665667
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1991-2000 GMC C2500 | Sierra, Sierra SL, Sierra SLE, Sierra SLT, Sierra SLX | 6 Cyl 4.3 L GAS, 8 Cyl 5.0 L GAS, 8 Cyl 5.7 L CNG, 8 Cyl 5.7 L GAS, 8 Cyl 6.2 L DIESEL, 8 Cyl 6.5 L DIESEL, 8 Cyl 7.4 L GAS
View related parts
GMC C2500 Caliper, Front Driver Side Part Number: 18036664
Product Specifications
- Other Name: Caliper Assembly, Front Brake (Remanufacture); Brake Caliper
- Position: Front Driver Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1984-1986 GMC C2500 | Base, High Sierra, Sierra Classic | 6 Cyl 4.1 L GAS, 6 Cyl 4.3 L GAS, 6 Cyl 4.8 L GAS, 8 Cyl 5.0 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 6.2 L DIESEL, 8 Cyl 7.4 L GAS
View related parts
GMC C2500 Caliper, Front Passenger Side Part Number: 18036663
Product Specifications
- Other Name: Caliper Assembly, Front Brake (Remanufacture); Brake Caliper
- Position: Front Passenger Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1984-1986 GMC C2500 | Base, High Sierra, Sierra Classic | 6 Cyl 4.1 L GAS, 6 Cyl 4.3 L GAS, 6 Cyl 4.8 L GAS, 8 Cyl 5.0 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 6.2 L DIESEL, 8 Cyl 7.4 L GAS
View related parts
GMC C2500 Caliper, Front Passenger Side Part Number: 18014748
Product Specifications
- Other Name: Caliper Kit, Front Brake; Brake Caliper; Caliper, Wheel Brake Cylinder/Caliper
- Position: Front Passenger Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1988-2000 GMC C2500 | Sierra, Sierra SL, Sierra SLE, Sierra SLT, Sierra SLX | 6 Cyl 4.3 L GAS, 8 Cyl 5.0 L GAS, 8 Cyl 5.7 L CNG, 8 Cyl 5.7 L GAS, 8 Cyl 6.2 L DIESEL, 8 Cyl 6.5 L DIESEL, 8 Cyl 7.4 L GAS
View related parts
GMC C2500 Caliper, Front Driver Side Part Number: 18014747
Product Specifications
- Other Name: Caliper Kit, Front Brake; Brake Caliper; Caliper, Wheel Brake Cylinder/Caliper
- Position: Front Driver Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1988-2000 GMC C2500 | Sierra, Sierra SL, Sierra SLE, Sierra SLT, Sierra SLX | 6 Cyl 4.3 L GAS, 8 Cyl 5.0 L GAS, 8 Cyl 5.7 L CNG, 8 Cyl 5.7 L GAS, 8 Cyl 6.2 L DIESEL, 8 Cyl 6.5 L DIESEL, 8 Cyl 7.4 L GAS
View related parts
GMC C2500 Caliper, Front Part Number: 18014745
Product Specifications
- Other Name: Caliper, Front Brake; Brake Caliper; Caliper, Wheel Brake Cylinder/Caliper
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1988-2000, 1985-1986 GMC C2500 | Base, Sierra, Sierra SL, Sierra SLE, Sierra SLT, Sierra SLX | 6 Cyl 4.3 L GAS, 6 Cyl 4.8 L GAS, 8 Cyl 5.0 L GAS, 8 Cyl 5.7 L CNG, 8 Cyl 5.7 L GAS, 8 Cyl 6.2 L DIESEL, 8 Cyl 6.5 L DIESEL, 8 Cyl 7.4 L GAS
View related parts
GMC C2500 Caliper, Front Part Number: 18014744
Product Specifications
- Other Name: Caliper, Front Brake; Brake Caliper; Caliper, Wheel Brake Cylinder/Caliper
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1988-2000, 1985-1986 GMC C2500 | Base, Sierra, Sierra SL, Sierra SLE, Sierra SLT, Sierra SLX | 6 Cyl 4.3 L GAS, 6 Cyl 4.8 L GAS, 8 Cyl 5.0 L GAS, 8 Cyl 5.7 L CNG, 8 Cyl 5.7 L GAS, 8 Cyl 6.2 L DIESEL, 8 Cyl 6.5 L DIESEL, 8 Cyl 7.4 L GAS
View related parts
GMC C2500 Caliper, Front Driver Side Part Number: 19140915
$49.39 MSRP: $89.79
You Save: $40.40 (45%)
Product Specifications
- Other Name: Caliper, Front Brake (W/O Brake Pads) (Remanufacture); Brake Caliper; Caliper, Wheel Brake Cylinder/Caliper
- Position: Front Driver Side
- Replaces: 18021434, 18015385, 18036672
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1984-1986 GMC C2500 | Base, High Sierra, Sierra Classic | 6 Cyl 4.1 L GAS, 6 Cyl 4.3 L GAS, 6 Cyl 4.8 L GAS, 8 Cyl 5.0 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 6.2 L DIESEL, 8 Cyl 7.4 L GAS

GMC C2500 Brake Calipers

Want to cut long-term maintenance and repair costs? Choose OEM Brake Calipers. Those parts deliver top durability you can trust. On our site, you'll find a huge catalog of genuine GMC C2500 parts. Prices are unbeatable, so you can keep more in your pocket. Every OEM GMC C2500 Brake Calipers includes a manufacturer's warranty. You can also get an easy return policy that keeps buying risk free. Fast delivery, get your car on the road quickly. It's simple to search, compare, and order. Stop guessing about quality or fit. Order today and save with parts that last.

It is without any doubt that the GMC C2500 Brake Calipers are very essential parts that play a major role in improving the braking system of the vehicle to make it more safe. These brake calipers are highly acclaimed for their dependability and efficiency; the purpose of these brake calipers is to transform hydraulic pressure into mechanical force to enable the GMC C2500 to stop efficiently no matter the driving conditions. As for the available types we comprehend the fixed and floating GMC C2500 Brake Calipers, while the first one applies multiple pistons to ensure equal pressure when applied for optimal braking, the second one is based on the pins and its slide in order to achieve the necessary performance. Thus, the compatibility of these brake calipers with numerous GMC C2500 models of different trims such as GMC C2500 Base, GMC C2500 Deluxe, and GMC C2500 Sierra gives the customers an opportunity to pick the demanded brake calipers for their vehicles of any configuration. Actual functionality is not the only importance of the GMC C2500 Brake Calipers: they are crucial to the truck's safety, including such problems as brake pull or dragging brakes caused by caliper abnormalities. Also, performance calipers help to improve the braking system; therefore, the GMC C2500 is one of the best trucks for any robust assignments. Due to the fact that the new seals, dust boots and bleeder screws are included in the list of the replacement options, GMC C2500 Brake Calipers are considered to be unique in automotive market because of their sturdiness and their consideration of the broader conception of the automobile's design; thus, this legendary pickup will remain one of the most reliable vehicles for quite a long time.

GMC C2500 Brake Calipers Parts Questions & Experts Answers

Caliper, Front
18014745
Q: How to service and ensure proper assembly of brake calipers on GMC C2500?
A:
Change all of the items in the service and repair kit and do not forget to lubricate the rubber parts with clean brake fluid before assembling. After any components are removed or unplugged, bleeding the brake system may be needed and Brake Pads need to be replaced inside every axle set only. Refer to the torque values for unlubricated fasteners and perform your work in a bench that does not contain any mineral oil substances. Try not to hold your fingers where the Piston is located to avoid getting hurt. The first step is to take off the brake caliper from the vehicle. Set a hardwood piece in front of the Piston for protection and then slide the Piston out by blowing air through the brake hose inlet fitting of the brake caliper's body. Following this, you should pull out the Piston boot, the Piston seal, bleed screw cap and the bleed screw. Check for any surface damage or rust on the brake caliper bore and on the groove for the Piston seal and if serious damage is noted, replace the caliper housing. Examine the guide surfaces of the brake caliper bracket for rust and damage and swap the bracket if you notice any signs of wear or rust. Remove any residue from the parts of the Brake Pad guiding surfaces on the brake caliper housing and mounting bracket and clean and dry all other parts with denatured alcohol after drying with air. Make sure every passage inside the brake caliper housing and the brake caliper bleeder valve has been blown out. The next step is to put in the bleed screw and tighten it to 12 n.m (106 lb in) before fitting the bleed screw cap. Pour brake fluid onto both the new Piston seal and the brake caliper bore groove before putting the seal into place, making sure it does not twist. Apply brake fluid to the brake caliper bore and to the Piston and then install the boot and Piston with the boot fitting snugly into both. Give the additional Piston the same treatment and reassemble it as well. The last step is to secure the brake caliper back to the vehicle.