How to replace the front brake pads on the 25/3500 Series on GMC Sierra 3500?

Start front pad replacement on the 25/3500 series by checking brake master cylinder fluid level; you can keep the current fluid if the reservoir sits at mid-point between maximum and minimum marks but you need to reduce the fluid if it sits above the midpoint. Insert a caliper compressor tool inside the brake caliper housing and press the two c-clamps tightly to push the pistons completely back. Pull out the brake caliper bolts without pressing the brake pedal as you take both rotors and calipers out. Hold the caliper steady using mechanic's wire without disconnecting the brake hose before you take out the brake pads and remove the old anti-rattle clips. Before adding new parts check the caliper and bracket condition then place the disc brake pads inside properly for 2500 series with wear sensor and 3500 series standards. Secure the caliper to the bracket by installing its bolts and tightening them to 80 ft. Lbs. (108 Nm). Put back the wheel and tire unit then take away the safety stands while lowering the vehicle down. Step on the brake pedal when the engine is off and slowly apply it to about 2/3 of its total range before easing up. Keep performing this action until the pedal feels solid to ensure the brake caliper pistons and pads are correctly seated. Clear brake fluid needs to be added up to the proper mark in the master cylinder tank and pads should be run against rotors to smooth out their surfaces.

OEM GMC Sierra 3500 Brake Pad

Disc Brake Pad Set

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

7 Brake Pads found

View related parts
GMC Sierra 3500 Brake Pads, Front
Part Number: 19432941
$125.81 MSRP: $263.80
You Save: $137.99 (53%)
ADD TO CART
Product Specifications
- Other Name: Pad Kit, Front Disc Brake; Front Pads; Pad Kit, Brake
- Position: Front
- Replaces: 15886468, 18048600, 18044594, 88950732, 18026219, 19210706, 25924485, 88964201, 84292732
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2006 GMC Sierra 3500 | SL, SLE, SLT, WT | 8 Cyl 6.0 L GAS, 8 Cyl 6.6 L DIESEL, 8 Cyl 8.1 L GAS
View related parts
GMC Sierra 3500 Brake Pads
Part Number: 19210705
Product Specifications
- Other Name: Pad Kit, Brake; Disc Brake Hardware Kit; Rear Pads; Front Pads
- Position: Rear
- Replaces: 18041762, 18026217
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2005 GMC Sierra 3500 | Base, SLE, SLT, WT | 8 Cyl 6.0 L CNG, 8 Cyl 6.0 L GAS, 8 Cyl 6.6 L DIESEL, 8 Cyl 8.1 L GAS
View related parts
GMC Sierra 3500 Brake Pads
Part Number: 19133307
Product Specifications
- Other Name: Pad Kit, Brake; Disc Brake Hardware Kit; Rear Pads
- Position: Rear
- Replaces: 18044346
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2001-2006 GMC Sierra 3500 | Base, SL, SLE, SLT, WT | 8 Cyl 6.0 L CNG, 8 Cyl 6.0 L GAS, 8 Cyl 6.6 L DIESEL, 8 Cyl 8.1 L GAS
View related parts
GMC Sierra 3500 Brake Pads, Front
Part Number: 19133306
Product Specifications
- Other Name: Pad Kit, Front Disc Brake; Disc Brake Hardware Kit; Front Pads; Pad Kit, Brake
- Position: Front
- Replaces: 18042334
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2001-2006 GMC Sierra 3500 | Base, SL, SLE, SLT, WT | 8 Cyl 6.0 L CNG, 8 Cyl 6.0 L GAS, 8 Cyl 6.6 L DIESEL, 8 Cyl 8.1 L GAS
View related parts
GMC Sierra 3500 Brake Pads, Front
Part Number: 18048101
Product Specifications
- Other Name: Pad Kit, Front Disc Brake; Disc Brake Hardware Kit; Rear Pads; Front Pads; Pad Kit, Brake
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2006 GMC Sierra 3500 | SL, SLE, SLT, WT | 8 Cyl 6.0 L GAS, 8 Cyl 6.6 L DIESEL, 8 Cyl 8.1 L GAS
View related parts
GMC Sierra 3500 Brake Pads
Part Number: 18045936
Product Specifications
- Other Name: Pad Kit, Brake
- Position: Rear
- Replaces: 18043517, 18044202
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2001-2005 GMC Sierra 3500 | Base, SL, SLE, SLT, WT | 8 Cyl 6.0 L CNG, 8 Cyl 6.0 L GAS, 8 Cyl 6.6 L DIESEL, 8 Cyl 8.1 L GAS
View related parts
GMC Sierra 3500 Brake Pads
Part Number: 18048083
Product Specifications
- Other Name: Pad Kit, Brake; Disc Brake Hardware Kit; Rear Pads
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2006 GMC Sierra 3500 | SL, SLE, SLT, WT | 8 Cyl 6.0 L GAS, 8 Cyl 6.6 L DIESEL, 8 Cyl 8.1 L GAS

GMC Sierra 3500 Brake Pad

Our website offers an extensive catalog of genuine GMC Sierra 3500 Brake Pad at unbeatable prices. Every OEM GMC Sierra 3500 Brake Pad comes with a manufacturer's warranty, an easy return policy, and rapid delivery service. Don't miss out on this great opportunity!

GMC Sierra 3500 Brake Pad Parts Questions & Experts Answers

Brake Pads
19133307
Q: How to replace the front brake pads on the 25/3500 Series on GMC Sierra 3500?
A: Start front pad replacement on the 25/3500 series by checking brake master cylinder fluid level; you can keep the current fluid if the reservoir sits at mid-point between maximum and minimum marks but you need to reduce the fluid if it sits above the midpoint. Insert a caliper compressor tool inside the brake caliper housing and press the two c-clamps tightly to push the pistons completely back. Pull out the brake caliper bolts without pressing the brake pedal as you take both rotors and calipers out. Hold the caliper steady using mechanic's wire without disconnecting the brake hose before you take out the brake pads and remove the old anti-rattle clips. Before adding new parts check the caliper and bracket condition then place the disc brake pads inside properly for 2500 series with wear sensor and 3500 series standards. Secure the caliper to the bracket by installing its bolts and tightening them to 80 ft. Lbs. (108 Nm). Put back the wheel and tire unit then take away the safety stands while lowering the vehicle down. Step on the brake pedal when the engine is off and slowly apply it to about 2/3 of its total range before easing up. Keep performing this action until the pedal feels solid to ensure the brake caliper pistons and pads are correctly seated. Clear brake fluid needs to be added up to the proper mark in the master cylinder tank and pads should be run against rotors to smooth out their surfaces.